MEEC TOOLS 012594 18V Angle Grinder Instruction Manual

MEEC TOOLS 012594 18V Angle Grinder

SAFETY INSTRUCTIONS

WARNING!
Read all warnings, safety instructions and other instructions carefully before use. Failure to follow all the instructions and e safty instructions can result in the risk of electric shock, fire and/or serious personal injury.

WORK AREA

• Keep the work area clean and well lit. Dark and cluttered work areas increase the risk of accidents and injuries.
• Do not use power tools in explosive environments, such as in the vicinity of flammable liquids, gas or dust. Power tools produce sparks that can ignite dust and fumes.
• Keep children and onlookers at a safe distance when using power tools. You can easily lose control of the tool if you are distracted.

ELECTRICAL SAFETY

• The plug on the power tool must match the power point. Neve r modify the plug in any way. Never use an adapter w ith earthed power tools. Unmodified plugs and matching outlets reduce the risk of electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
• Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
• Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the power point. Keep the power cord away from heat, oil, sharp edges and moving parts. Damaged or tangled power cords increase the risk of electric shock.
• Only use an extension cord approved for outdoor use. Cords intended for outdoor use reduce the risk of electric shock.
• If it is absolutely necessary to use power tools in damp conditions, use a power point protected by a residual current device RDC. Using an RCD reduces the risk of electric shock.

PERSONAL SAFETY

• Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use
  power tools if you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when using a
  power tool can result in serious personal
  injury.

• Use personal safety equipment. Wear safety glasses.

• Depending on the type of tool and how it is used, safety equipment such as dust masks, non-slip safety shoes, safety
  helmets and ear protection reduce the risk of personal injury.

• Never saw in asbestos.

• Dust from oak, ash and other types of wood can be carcinogenic. Use a dust mask and ensure there is adequate
  ventilation.

• Avoid accidental starting. Check that the power switch is in the OFF position before plugging in the power cord and/or the battery, or lifting/carrying the tool. Carrying a power tool with your finger on the switch, r o connecting a tool to the mains suppy when the switch is in the ON position increases the risk of accidents and injuries.

• Remove Allen keys/spanners etc. before starting the tool.

• Spanners or the like that are left in a rotating part of the tool can cause personal injury.

• Do not overreach. Always maintain a firm footing and good balance. This will ensure you have better control over the tool in unexpected situations.

• Wear suitable clothing. Do not wear loose-fitting clothing or jewellery.

• Keep your hair, clothing and gloves away from moving parts. Loose-fitting clothing, jewellery and long hair can get caught in moving parts.

• If dust extraction and dust collection equipment is available, this should be connected and used correctly. The use of such devices can reduce the risk of
  dust-related problems.

USING AND LOOKING AFTER POWER TOOLS

• Do not force the power tool. Use the correct power tool for the planned work. The tool does the job better and safer when used at the rate for which it was designed.
• Do not use the tool if it cannot be switched on and off with the power switch. Power tools that cannot be controlled with the power switch are dangerous and must be repaired.
• Unplug the power cord before making any adjustments, changing accessories or putting the power tool away. These safety precautions reduce the risk of accidently starting the power tool.
• Store power tools out of the reach of children when not in use. Never allow children, or anyone who is unfamiliar with the power tool and these instructions,  to use the tool. Power tools are dangerous if used by inexperienced persons.
• Keep the power tool properly maintained. Check that moving parts are properly adjusted and do not jam, and that no parts are incorrectly fitted or damaged. Check for other factors that could affect functionality. If the power tool is damaged, it must be repaired before being used again. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control.
• Use the power tool, accessories and bits etc., in accordance with these instructions, taking into account the actual working conditions and the work that is to be done. It can be dangerous to use power tools for purposes other than those they are intended to be used for.

USING AND MAINTAINING BATTERY-POWERED TOOLS

• Only charge the battery with the charger recommended by the manufacturer. Charging other batteries can result in a risk of personal injury and/or fire.
• Only use batteries recommended by the manufacturer. The use of other batteries can result in a risk of personal injury and/ or fire.
• When the battery is not in use keep it away from metal objects such as paperclips, coins, keys, nails, screws and other small metal objects that can short circuit the terminals. Short circuiting discharges large amounts of energy that can cause a fire and/or burn injuries.
• Failure to handle the battery carefully can cause fluid to leak from the battery. Avoid contact with battery fluid. On contact with battery fluid, rinse immediately with plenty of fresh water. Seek medical attention if you get battery fluid in your eyes. Battery fluid can cause skin irritation and/or burns.

SERVICE
The power tool must only be serviced by qualified personnel using identical spare parts. This will ensure that the power tool remains safe to use.

SAFETY INSTRUCTIONS FOR ANGLE GRINDERS

General safety instructions for all types of grinding. .

• This power tool is intended to be used as a grinder. Read all the safety instructions, other instructions, illustrations and specifications supplied with this power tool. Failure to follow all the instructions below can result in the risk of electric shock, fire and/or serious personal injury.

• This power tool can be used for grinding and steel brushing. Using the tool for any other purpose can be dangerous and cause personal injury.

• This power tool is not intended to be used for polishing.

• Do not use accessories that are not specifically designed and recommended by the tool manufacturer. Just because an accessory can be connected to the power tool does not mean it is safe to use. The rated speed of the accessory must be at least equal to the specified maximum speed of r the power tool. Accessories that r un faster than the spec fied rated speed may break or fly apart.

• The outer diameter and thickness of the accessory must be within the rated capacity of the power tool. Accessories of the wrong size cannot be properly protected and controlled.

• Threaded mounting of accessories must r match the spindle thread on the grinder.

• Fo flange-f tted accessories, the spindle hole must match the control diameter of the flange. Accessories that do not fit the attachments on the tool wiill lbe unbalanced, vibrate excess ve y and can cause you to lose control of the tool.

• Do not use damaged accessories. Before using the tool always check the accessory and make sure, for example, that the edges of grinding discs are not damaged, that there are no cracks or wear on the backing pad, and that the steel brush does not have any loose or damaged bristles. If you drop the power tool or an accessory, check that it is not damaged, or fit an undamaged accessory. After checking and fitting an accessory, position yourself and other people in the vicinity away from the direction of rotation of the accessory and then run the tool at its maximum no-load speed for one minute. Damaged accessories will normally break during this test period.

• Wear safety equipment. Depending on the area of use, you should wear a visor, goggles or safety glasses. When necessary you should wear a dust mask, ear protection, gloves and an apron that can stop shavings and fragments from the workpiece. The eye protection must be able to stop flying debris produced by the tool. The dust or breathing mask must be able to filter out the particles produced by the tool. Prolonged exposure to intense noise can impair hearing.

• Keep onlookers at a safe distance from the work area. Everyone coming into the work area must wear personal safety equipment. Fragments from the workpiece, or from a defective accessory, can fly out and cause personal injury outside the actual work area.

• Hold the tool with the insulated grips if there is a risk of coming into contact with hidden wiring or the power cord to the tool. When cutting accessories come into contact with a live wire, unprotected metal parts on the tool may become charged and give the user an electric shock.

• Position the power cord so that it cannot come into contact with the rotating accessory. If you lose control, the power cord can be cut or get stuck, and your hand or arm could be pulled into the
  rotating accessory.

• Never put down the power tool until the accessory has completely stopped. The rotating accessory can catch on the surface and cause you to lose control of the power tool.

• Do not run the tool while carrying it next to you. Unintentional contact with the rotating accessory can cause it to catch in your clothes and pull it towards your body.

• Clean the ventilation grilles on the tool at regular intervals. The motor fan sucks dust into the tool casing and the accumulation of metal powder can result in the risk of electric shock.

• Do not use the power tool near flammable materials. Sparks can ignite these materials.

• Do not use accessories that require liquid coolants. The use of water or other liquid coolants can cause an electric shock.

ADDITIONAL SAFETY INSTRUCTIONS

Kickback and other warnings
Kickback is a sudden reaction when a rotating disc, backing pad, brush or other accessory jams or catches on something. Jamming or catching wi 11 ca use the rotating accessory to block suddenly, which in turn can force the power tool in the opposite direction to the rotating accessory. For example, if a grinding disc pinches or sticks in the workpiece, the edge of the disc that goes in at the sticking point could dig into the material and cause the disc to recoil and kick back. The disc can jump either towards or away from the user, depending on the direction of rotation of the disc when it jams. Grinding discs can also break in these situations. Kickback is a result of the incorrect use of the power tool, and/or incorrect procedures and working conditions. Kickback can be avoided by observing the safety measures described below:

• Keep a firm grip on the tool and position your body and arm so you can resist the force of a sudden kickback. Always use the support handle, if there is one, for maximum control of the kickback or torque response when starting the tool. The user can control torque response and kickback if the appropriate precautions are taken.
• Never put your hands near the rotating accessory. Kickback can cause the accessory to touch your hand.
• Keep your body away from the area where the power tool will go if there is a kickback. Kickback forces the tool in the opposite direction to the rotation of the disc.
• Take extra care when working on corners and sharp edges, etc. Avoid letting the accessory bounce or catching. Corners, sharp edges and bouncing can cause the rotating accessory to catch and cause the user to lose control of the tool, or cause it to kick back.

SAFETY INSTRUCTIONS SPECIFIC TO GRINDING AND ABRASIVE CUTTING

• Use only the types of disc recommended for your power tool and the specific protection designed for your chosen disc. Discs that the tool is not designed for cannot be properly protected and are therefore not safe.
• The grinding surface on discs with a recessed centre must be fitted below the plane of the protective flange.
• An incorrectly fitted disc that projects through the plane of the protective flange cannot be properly protected.
• The guard must be firmly fixed to the power tool and positioned for maximum safety, so that the smallest possible part of the disc is exposed to the user.
• The guard helps to protect the user against broken-off fragments of disc, accidental contact with the disc, and sparks that could set fire to clothing.
• Discs must only be used for the recommended applications. For example: Do not grind with the side of a cutting disc. Abrasive cutting discs are intended for grinding with the outer edges. If lateral forces are applied to these discs, they can shatter.
• Always use undamaged disc flanges of the right size and shape for the disc you have chosen. Correct disc flanges support the disc and therefore reduce the risk of the disc breaking. Flanges for cutting discs can differ from flanges for grinding discs.
• Do not use worn down discs from a larger power tool. Discs from larger power tools are not suitable for the higher speeds of small tools and can shatter.

SAFETY INSTRUCTIONS FOR BONDED GRINDING DISCS
Grinding discs can break and are sensitive to impact and pressure. For this reason take the following precautions when handling grinding discs:

• Do not drop grinding discs or subject them to knock and blows.
• Do not use damaged grinding discs or discs that have been dropped.
• Avoid damaging the centre hole.
• Do not subject grinding discs to heavy weights; do not put anything on top of them.
• Store grinding discs flat, or upright in a dry and frost-free place.
• When possible keep grinding discs in their original packaging, or in special containers or on special shelves.

VIBRATION AND NOISE ATTENUATION
To reduce the effects of noise and vibrations you should limit the time in use, use the low-vibration and low-noise modes, and wear personal safety equipment. Observe the following to minimise the risk of exposure to vibrations and loud noise:

• Only use the power tool for the purpose it was designed for, and in accordance with these instructions.
• Make sure that the power tool is in good condition and well maintained.
• Use the right accessories for the power tool and make sure they are in good condition.
• Keep a firm grip on the handles/gripping surface.
• Maintain the power tool in accordance with these instructions and make sure it is well lubricated (where applicable).
• Plan the work schedule to spread the use of tools with heavy vibrations over a longer period.

EMERGENCY MODE
Familiarise yourself with the use of this power tool with the help of these instructions. Commit the safety instructions to memory and follow them to the letter. This will help you to avoid risks and dangerous situations.

• Always pay attention when using this power tool, so that you can detect and handle risks at an early stage. Prompt action can prevent serious personal injury and material damage.
  Switch off the power tool and unplug it from the power supply in the event of a fault. Make sure the power tool is checked by a qualified professional, and if necessary repaired, before using it again.

OTHER RISKS
Even if you use this power tool in accordance with all the safety instructions, there is still a risk of personal injury and other damage. The following hazards related to the design and construction of this power tool can occur:

• Effects on health from vibration if the tool is used for long periods, or is not handled and maintained correctly.
• Personal injury and material damage as a result of defective accessories and hitting hidden objects when using the tool.
• Risk of personal injury and material damage as a result of ejected objects.
• Damage to lungs (if an effective face mask is not worn).
• Damage to ears (if effective ear protection is not worn).

WARNING!
This power tool produces an electromagnetic field during use. This field can in some circumstances affect active or passive medical implants. To reduce the risk of serious or life-threatening injury, persons with medical implants are therefore advised to consult their doctor and the manufacturer of the implant before using this power tool.

Symbols
The following symbols can be of importance for how you should use your power tool. Make sure you understand the symbols and their significance.

TECHNICAL DATA

• Battery voltage 18 V DC
• Speed, no load 8000 rpm
• Outer diameter of disc 115 mm
• Hole diameter 22 mm
• Spindle M14
• Weight 1.82 kg
• Sound power level, LwA_ 89.5 dB(A), K=3 dB
• Sound pressure level, LpA 78.5 dB(A), K=3 dB
• Vibration level, ah,AG 7.54 m/s, K=1.5 m/s*

Always wear ear protection.
The declared values for vibration and noise, which have been measured according to a standardised test method, can be used to compare different tools with each other and for a preliminary assessment of exposure. The measurement values have been determined in accordance with EN 60745-2-3.

WARNING!
The actual vibration and noise level when using tools may differ from the specified maximum value, depending on how the tool is used and the material. It is therefore necessary to determine which safety precautions are required to protect the user, based on an estimate of exposure in actual operating conditions (taking into account all stages of the work cycle, e.g. the time when the tool is switched off and when it is idling, in addition to the start- up time).

DESCRIPTION

1. Inner flange disc
2. Outer flange disc
3. Guard
4. Handle
5. Spanner
6. Grinding/cutting disc
7. spindle lock button
8. Spindle

ASSEMBLY

IMPORTANT:
Switch off and unplug the tool from the mains before working on the tool.

GUARD
Fit the guard (3) as shown in the diagrams. Adjust the clamping force of the locking arm by tightening the hex screw out or in when the locking arm is unloaded.

HANDLE
The extra handle (4) is mounted on the left or right side, or a lternative ly on the top of the tool. Choose the position that provides the most comfortable and safest handling.

CiRINDINCi/CUTTINCi DISC

1. Place the inner flange disc (1) over the spindle with the locking edges (A) facing down and make sure that the edges of the disc and spindle (8) lock w ith each other. The flange disc must not rotate freely, but must follow the rotation of the spindle.
2. Put the grinding or cutting disc on the inner flange disc and align the hole to the shoulder.
3. Now fit the outer flange disc (2) and tighten with the spanner (5). Press and hold in the button for the spindle lock (7) to prevent the spindle from rotating during the tightening.
4. After fitting or replacing the disc the angle grinder should be test-run at low speed for a few minutes, without applying the disc against an object. If the disc is damaged it must be replaced immediately.

USE

APPLICATIONS
This angle grinder can be used to grind steel, stone and ceramic objects. Never attempt to grind wood or soft metals such as lead. Such materials will quickly “clog” the grinding disc and make it unusable.

BEFORE USE
Make sure before use that the grinding/cutting disc, power cable and the rest of the tool is undamaged. The guard must be mounted in such a way that it prevents particles from reaching the user. Never cover the ventilation holes when the tool is in use. This can damage the motor and reduce the functionality of the tool.

GRINDING

NOTE:
Do not switch on or off the power switch when the product is in contact with the workpiece. This reduces the life span of the power switch and can damage the workpiece.

1. Tilt the product at an angle of 70° to 15° for easy handling and smooth grinding.
2. Place the disc against the workpiece with a light and firm pressure for maximum grinding. It is never necessary to use the angle grinder with extreme force. The weight of the angle grinder provides sufficient pressure.
3. Too much pressure will eventually overload the motor, slow down grinding, dangerously over tension the disc and break it.
4. Move the angle grinder smoothly back and forth over the workpiece.

MAINTENANCE

WARNING!
Always make sure that the tool is switched off and unplugged from the mains before doing any checks or maintenance. Always make sure that the tool is switched off and unplugged from the mains before doing any checks or maintenance.

• The body and motor holder are essential parts of the power tool. Carefully check that they are not damaged or exposed to oil or water.
• Check at regular intervals all fasteners and screws, and make sure that they are properly tightened. Tighten any loose screws immediately. Failure to do this can result in serious injury.
• You should allow an authorised service centre to clean and lubricate this tool at least once a year.
• Make sure that the tool is clean and free from dust after use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>