GOLDEN LIGHTING 4308-OWM Outdoor Wall Light Installation Guide
- June 4, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 4308-OWM Outdoor Wall Light
Dimensions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Assembly Instructions
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
IMPORTANT:
- All installation work should be done by an accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixtures from the wall, including the old mounting strap. 1. Take the mounting strap assembly from the parts bag. Mounting strap (A) contains threaded holes. Two of mounting screws (C) should be attached to the mounting strap (A). You may need to tighten the nuts that hold these screws in place. Pull the house wires through the center of the mounting strap (A). Place mounting strap (A) over the junction box so that mounting screws (C) are horizontal, and in alignment with the hole locations on the fixture’s backplate (D). Secure mounting strap (A) to the junction box with mounting screws (B) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
(PLEASE NOTE: This fixture may be installed with the accent (1) or without the accent (2)) TO INSTALL WITH THE ACCENT, REFER TO DIAGRAM (1): 2. Loosen the screws (M) and remove the lower aluminum cover (L). Remove the nut (H) and place the accent (G) on the iron part (P) of the lamp body. Secure accent (G) with nut (H). Insert glass sheets (I) and (J) into the middle of the aluminum strip (K) of the lamp body. Place the lower aluminum cover (L) on the aluminum strip (K) and fasten it with screws (M). TO INSTALL WITHOUT THE ACCENT, REFER TO DIAGRAM (2): 2. Loosen the screws (M) and remove the lower aluminum cover (L). Insert glass sheets (I) and (J) into the middle of the aluminum strip (K) of the lamp body. Place the lower aluminum cover (L) on the aluminum strip (K) and fasten it with screws (M)
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of the ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Place the fixture’s backplate (D) over mounting screws (C) so that they protrude through the holes in the front of the backplate (D). Thread deco nuts (F) onto mounting screws (C). Twist until the backplate of the fixture is snug against the wall. 5. Install light bulbs (not included) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>