Teltonika FMB204 Glossary Water Resistant 2G GPS Tracker Instructions

: June 6, 2024
: teltonika

Teltonika FMB204 Glossary Water Resistant 2G GPS Tracker

Product Information

Model: FMB204
Type: Advanced Tracker
Manufacturer: Teltonika

Product Usage Instructions

Installation:
Follow the installation guide provided in the FMB204 manual to properly install the tracker in your vehicle.
Power On:
Once installed, power the FMB204 tracker by connecting it to a power source according to the manual instructions.
Configuration:
Configure the tracker settings using the manual to set up tracking parameters, reporting intervals, and other preferences.
Tracking:
The FMB204 tracker will now start tracking your vehicle’s location based on the configured settings. Access the tracking data through the provided interface or software.
Maintenance:
Regularly check the tracker’s functionality and ensure it is securely connected to the power source for uninterrupted tracking.

FAQ

Q: How do I reset the FMB204 tracker?
A: To reset the tracker, refer to the manual for specific instructions on performing a reset procedure.
Q: Can I use the FMB204 tracker in multiple vehicles?
A: The FMB204 tracker can be transferred and used in different vehicles, but ensure to reconfigure it according to each vehicle’s requirements.

KNOW YOUR DEVICE

PINOUT

PIN NAME/DESCRIPTION

VCC (6-30) V Power supply (6-30) V DC (+).
GND (-) Ground pin. (6-30) V DC (-)
DIN 1 Digital input, channel 1.
DIN 2 Digital input, channel 2.
DIN 3 Digital input, channel 3.
AIN 1 Analog input, channel 1. Input range: 0-30 V DC.
DOUT 1 Digital output, channel 1. Open collector output. Max. 0,5 A DC.
DOUT 2 Digital output, channel 2. Open collector output. Max. 0,5 A DC.
1WIRE DATA Data for 1–Wire devices.
1WIRE POWER +3,8 V output for 1–Wire devices.

WIRING SCHEME

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD

UNSCREW SCREWS
Unscrew 6 screws counterclockwise that are located on the bottom of the device.
COVER REMOVAL
Remove the cover
MICRO-SIM CARD INSERT
Insert the Micro-SIM card as shown with the PIN request disabled or read our Wiki1 on how to enter it later in Teltonika Configurator2. Make sure that the Micro-SIM card cut-off corner is pointing forward to the slot.
wiki.teltonika-gps.com/view/FMB204_Security_info
wiki.teltonika-gps.com/view/Teltonika_Configurator.
BATTERY CONNECTION
Connect the battery as shown to the device.
ATTACHING COVER BACK
After configuration, see “PC Connection (Windows)1”, attach the device cover back and screw in all screws.
DEVICE IS READY
The device is ready to be mounted.

PC CONNECTION

PC CONNECTION (WINDOWS)

Power-up FMB204 with DC voltage (10 – 30 V) power supply using supplied power cable. LEDs should start blinking, see “LED indications1”.
Connect the device to the computer using a Micro-USB cable or Bluetooth connection:
- Using Micro-USB cable
- You will need to install USB drivers, see “How to install USB drivers (Windows)2”
- Using Bluetooth
- FMB204 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device > Bluetooth. Choose your device named – “FMB204_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.

wiki.teltonika-gps.com/view/FMB204_LED_status

HOW TO INSTALL USB DRIVERS

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here.
Extract and run TeltonikaCOMDriver.exe.
Click Next in the driver installation window.
In the following window click the Install button.
Setup will continue installing the driver and eventually, the confirmation window will appear. Click Finish to complete the setup.

CONFIGURATION

At first, the FMB204 device will have default factory settings set. These settings should be changed according to the user’s needs. The main configuration can be performed via Teltonika Configurator1 software. Get the latest Configurator version from here2. Configurator operates on Microsoft Windows OS and uses the prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS.NET REQUIREMENTS

Operating system
- Windows Vista
- Windows 7
- Windows 8.1
- Windows 10
MS .NET Framework version
MS .NET Framework 4.6.2
Version
32 and 64-bit
Links
www.microsoft.com.

dotnet.microsoft.com/en-us/download/dotnet- framework/net462.

Downloaded Configurator will be in a compressed archive. Extract it and launch Configurator.exe. After launch software language can be changed by clicking ? in the right bottom corner.

The configuration process begins by pressing on the connected device.

After connection to Configurator Status window will be displayed.

Various Status window1 tabs display information about GNSS2, GSM3, I/O4, Maintenance5, etc. FMB204 has one user-editable profile, which can be loaded and saved to the device. After any modification of configuration, the changes need to be saved to the device using the Save to Device button. Main buttons offer the following functionality:

Load from the device – loads configuration from the device.
Save to device – saves the configuration to the device.
Load from file – loads configuration from file.
Save to file – saves the configuration to file.
Update firmware – updates the firmware on the device.
Read records – reads records from the device.
Reboot device – restart device.
Reset configuration – sets device configuration to default.

The most important configurator section is GPRS – where all your server and GPRS settings6 can be configured and Data Acquisition7 – where data acquiring parameters can be configured. More details about FMB204 configuration using Configurator can be found in our Wiki8.

QUICK SMS CONFIGURATION

The default configuration has optimal parameters present to ensure the best performance of track quality and data usage.

Quickly set up your device by sending this SMS command to it:

Note:
Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

2001 – APN
2002 – APN username (if there are no APN usernames, an empty field should be left)
2003 – APN password (if there are no APN passwords, empty field should be left)
SERVER SETTINGS:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS

MOVEMENT AND IGNITION DETECTION:

THE DEVICE MAKES A RECORD OF MOVING IF ONE OF THESE EVENTS HAPPEN:

After successful SMS configuration, the FMB204 device will synchronize time and update records to the configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator1 or SMS parameters2.

MOUNTING RECOMMENDATIONS

CONNECTING WIRES

Wires should be fastened to the other wires or non-moving parts. Try to avoid heat emitting and moving objects near the wires.
The connections should not be seen very clearly. If factory isolation was removed while connecting wires, it should be applied again.
If the wires are placed in the exterior or in places where they can be damaged or exposed to heat, humidity, dirt, etc., additional isolation should be applied.
Wires cannot be connected to the board computers or control units.

CONNECTING POWER SOURCE

Be sure that after the car computer falls asleep, power is still available on the chosen wire. Depending on the car, this may happen in a 5 to 30-minute period.
When the module is connected, measure the voltage again to make sure it did not decrease.
It is recommended to connect to the main power cable in the fuse box.
Use 3A, 125V external fuse.

CONNECTING IGNITION WIRE

Be sure to check if it is a real ignition wire i. e. power does not disappear after starting the engine.
Check if this is not an ACC wire (when the key is in the first position, most of the vehicle electronics are available).
Check if power is still available when you turn off any of vehicles devices.
The ignition is connected to the ignition relay output. As an alternative, any other relay, that has power output when ignition is on, may be chosen.

CONNECTING GROUND WIRE

The ground wire is connected to the vehicle frame or metal parts that are fixed to the frame.
If the wire is fixed with the bolt, the loop must be connected to the end of the wire.
For better contact scrub paint from the spot where the op is going to be connected.

LED INDICATIONS

NAVIGATION LED INDICATIONS

BEHAVIOUR/MEANING

Permanently switched on GNSS signal is not received
Blinking every second in Normal mode, GNSS is working
Off
- GNSS is turned off because:
- The device is not working or the Device is in sleep mode
Blinking fast constantly Device firmware is being flashed

STATUS LED INDICATIONS

BEHAVIOUR/MEANING

Blinking every second in Normal mode
Blinking every two seconds Sleep mode
Blinking fast for a short time Modem activity
Off Device is not working or Device is in boot mode

BASIC CHARACTERISTICS

MODULE

Name Teltonika TM2500
Technology GSM, GPRS, GNSS, BLUETOOTH

GNSS

GNSS GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver 33 channel
Tracking sensitivity -165 dBM
Accuracy < 3 m
Hot start < 1 s
Warm start < 25 s
Cold start < 35 s

CELLUAR

Technology GSM
2G bands Quad-band 850 / 900 / 1800 / 1900 MHz
Data transfer GPRS Multi-Slot Class 12 (up to 240 kbps), GPRS Mobile Station Class B
Data support SMS (text/data)

POWER

Input voltage range 6-30 V DC with overvoltage protection
Back-up battery 1800 mAh Li-Ion battery 3.7 V (6.66 Wh)
Internal fuse 3 A, 125 V
- At 12V < 2.1 mA (Ultra Deep Sleep1)
- At 12V < 3.9 mA (Deep Sleep1)
- At 12V < 4.2 mA (Online Deep Sleep1)
Power consumption
- At 12V < 15.7 mA (GPS Sleep1)
- At 12V < 28.3 mA (nominal with no load)
- At 12V < 1.5 A Max. (with full load/Peak)

BLUETOOTH

Specification 4.0 + LE
Supported peripherals
- Temperature and Humidity sensor2, Headset3, OBDII dongle4,
- Inateck Barcode Scanner

INTERFACE

Digital Inputs 3
Digital Outputs 2
Analog Inputs 1
1-Wire DATA 1
1-Wire POWER 1
GNSS antenna Internal High Gain
GSM antenna Internal High Gain
USB 2.0 Micro-USB
LED indication 2 status LED lights
SIM Micro-SIM
Memory 128MB internal flash memory

PHYSICAL SPECIFICATION

Dimensions 72,5 x 73 x 27,3 mm (L x W x H)
Weight 205 g

OPERATING ENVIRONMENT

Operating temperature (without battery) -40 °C to +85 °C
Storage temperature (without battery) -40 °C to +85 °C
Battery Charging temperature 0 °C to +45 °C
Battery Discharge temperature -20 °C to +60 °C
Battery storage temperature
- -20 °C to +60 °C for 1 month
- -20 °C to +30 °C for 12 month
Operating humidity 5% to 95% non-condensing
Ingress Protection Rating IP67

FEATURES

Sensors Accelerometer
Green Driving, Over Speeding detection, Jamming detection, GNSS Fuel Counter, DOUT Control Via Call, Excessive Idling detection,
Scenarios
Immobilizer, iButton Read Notification, Unplug detection, Towing detection, Crash detection, Auto Geofence, Manual Geofence, Trip5
Sleep modes
GPS Sleep, Online Deep Sleep, Deep Sleep, Ultra Deep Sleep6.
Configuration and firmware update FOTA Web7, FOTA, Teltonika Configurator8 (USB, Bluetooth), FMBT mobile application (Configuration)
SMS Configuration, Events, DOUT control, Debug
GPRS commands Configuration, DOUT control, Debug
Time Synchronization GPS, NITZ, NTP
Fuel monitoring LLS (Analog), OBDII dongle10
Ignition detection Digital Input 1, Accelerometer, External Power Voltage, Engine RPM (OBDII dongle)

Links

ELECTRICAL CHARACTERISTICS

SAFETY INFORMATION

This message contains information on how to operate FMB204 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +6..+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of the device’s operation.
When connecting wires to the vehicle, the appropriate jumpers of the vehicle power supply should be disconnected.
Before unmounting the device from the vehicle, wires must be disconnected. The device is designed to be mounted in a zone of limited access, which is inaccessible to the operator. All related devices must meet the requirements of EN 62368-1 standard. The device FMB204 is not designed as a navigational device for boats.
Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply
All wireless data-transferring devices produce interference that may affect other devices that are placed nearby.
The device must be connected only by qualified personnel.
The device must be firmly fastened in a predefined location.
The programming must be performed using a PC with an autonomic power supply.
Installation and/or handling during a lightning storm is prohibited.
The device is susceptible to water and humidity if the device housing is not properly closed.
Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling centre or dispose of them in the battery recycle bin found in stores.

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User‘s Manual before you start using the device. The full User‘s Manual version can be found in our Wiki1.
- 1 wiki.teltonika-gps.com/index.php?title=FMB204
Hereby, Teltonika declares under our sole responsibility that the above-described product conforms with the relevant Community harmonization: European Directive 2014/53/EU (RED).
REACH addresses the production and use of chemical substances and their potential impacts on both human health and the environment. Its 849 pages took seven years to pass, and it has been described as the most complex legislation in the Union’s history and the most important in 20 years. It is the strictest law to date regulating chemical substances and will affect industries throughout the world.
The RoHS1 is a directive regulating the manufacture, import and distribution of Electronics and Electrical Equipment (EEE) within the EU, which bans from use of 10 different hazardous materials (to date).
The Declaration EAC and the Certificate EAC in conformity with the technical regulation TR CU of the EurAsEC Customs Union are EAC certification documents issued by independent organizations. Such organizations perform their function through laboratories accredited to the public agencies in charge of the supervision of metrology and standardization in the three countries of the EAC Customs Union, joining at the moment the certification system: Russia, Belarus, Kazakhstan, Armenia and Kyrgyzstan.
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
E-Mark and e-Mark are the European conformity marks issued by the transport sector, indicating that the products comply with relevant laws and regulations or directives. Vehicles and related products need to go through the E-Mark certification process to be legally sold in Europe.

DECLARATION OF IMEI ASSIGNMENT
The IMEI number is used by a GSM network to identify valid devices and therefore can be used to stop a stolen phone from accessing that network. For example, if a mobile phone is stolen, the owner can call their network provider and instruct them to blacklist the phone using its IMEI number. This renders the phone useless on that network and sometimes other networks too, whether or not the phone’s subscriber identity module (SIM) is changed.

DECLARATION OF DEVICE OPERATION TEMPERATURE
An operating temperature is the temperature at which an electrical or mechanical device operates. The device will operate effectively within a specified temperature range which varies based on the device function and application context and ranges from the minimum operating temperature to the maximum operating temperature (or peak operating temperature). Outside this range of safe operating temperatures, the device may fail.

CHECK ALL CERTIFICATES
All the newest certificates may be found in our Wiki2.

2 wiki.teltonika-gps.com/view/FMB204Certification&_Approvals.

WARRANTY

We guarantee our products a 24-month warranty1 period.
All batteries carry a 6-month warranty period.
Post-warranty repair service for products is not provided.

If a product stops operating within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
Replaced with a different product fulfilling the same functionality in case of EOL for the original product

Additional agreements for an extended warranty period can be agreed upon separately.

WARRANTY DISCLAIMER

Customers are only allowed to return products as a result of the product being defective, due to order assembly or manufacturing fault.
Products are intended to be used by personnel with training and experience.
Warranty does not cover defects or malfunctions caused by accidents, misuse, abuse, catastrophes, improper maintenance or inadequate installation – not following operating instructions (including failure to heed warnings) or use with equipment with which it is not intended to be used.
The warranty does not apply to any consequential damages.
Warranty is not applicable for supplementary product equipment (e.g. PSU, power cables, antennas) unless the accessory is defective on arrival.
More information on what is RMA1.

wiki.teltonika-gps.com/view/RMA_guidelines.