TELTONIKA RUTX09 Cellular IoT Router User Guide

: October 30, 2023
: teltonika

Table of Contents

FRONT VIEW
BACK VIEW
HARDWARE INSTALLATION
TECHNICAL INFORMATION
SAFETY INFORMATION
Documents / Resources

RUTX09 Cellular IoT Router
User Guide TELTONIKA RUTX09 Cellular IoT Router - qr
code https://wiki.teltonika.lt

FRONT VIEW

TELTONIKA RUTX09 Cellular IoT Router - fig

BACK VIEW

TELTONIKA RUTX09 Cellular IoT Router - fig 2

POWER SOCKET PINOUT

TELTONIKA RUTX09 Cellular IoT Router - fig 3

HARDWARE INSTALLATION

Pull out the SIM needle from the front panel of the router.
Push the SIM holder button with the SIM needle.
Pull out the SIM holder.
Insert your SIM card into the SIM holder.
Slide the SIM holder back into the router.
Attach mobile antennas.
Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter into a power outlet.
Connect to the using an Ethernet cable (connected to LAN port).

TELTONIKA RUTX09 Cellular IoT Router - fig 4

LOGIN TO DEVICE

To enter the router’s Web interface (Webeye), type http://192.168.1.1 into the URL ﬁeld of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you login, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory and you will not be able to interact with the router’s WebUI before you change the password.
When you change the router’s password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool used to setup some of the router’s main operating parameters.
Go to the Status > Network page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TELTONIKA RUTX09 Cellular IoT Router - fig 5

TECHNICAL INFORMATION

Radio speciﬁcations

RF technologies	GSM, GPRS, EDGE, UMTS/HSPA+, LTE, GNSS, WiFi
Max RF power	33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

**Bundled antennas speciﬁcations***

GSM/WCDMA/LTE antenna| 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain 3 dBi, omnidirectional, SMA male connector
---|---
GNSS antenna| 1575.42~1602 MHz, 2.2~5 VDC, VSWR < 1.5, active total gain 28 dB (typ.), RHCP polarization, SMA male connector

SAFETY INFORMATION

RUTX09 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.
Hereby, TELTONIKA declares that this RUTX09 is in compliance with the essential requirements and other relevant provisions of Directive CE/RED.
Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to conﬁgure it. More information on https://wiki.teltonika.lt
For more information visit www.teltonika.com
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
Hereby, Tectonic declares that the radio equipment type RUTX09 is in compliance with Directives: 2014/53/EU, 2014/35/EU, 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address: https://teltonika.It/product/rutx09/

www.teltonika.It
©2019 Tectonic