TELTONIKA TRB500 Industrial 5G Gateway User Guide

: October 30, 2023
: teltonika

Table of Contents

FRONT VIEW
16 PIN CONNECTOR PINOUT
HARDWARE INSTALLATION
DEVICE CONFIGURATION
TECHNICAL INFORMATION
SAFETY INFORMATION
Documents / Resources

TRB500 Industrial 5G Gateway
User Guidehttps://wiki.teltonika-networks.com/

FRONT VIEW

TELTONIKA TRB500 Industrial 5G Gateway - fig

BACK VIEW

TELTONIKA TRB500 Industrial 5G Gateway - fig 2

16 PIN CONNECTOR PINOUT

+ – 9-30 VDC positive power pin
D1, D2, D3 – Conﬁgurable digital Input/ Output pins. Open collector output, max output 30 V, 300 mA or Digital input where 0-6 V detected as logic low and 8-30 V – logic high.
CTS – RS232 clear data to send pin (output).
RTS – RS232 request data to send pin (input).
R+ – RS485 receiver positive signal pin.
D+ – RS485 driver positive signal pin.
– Negative/ground power pin.
– Ground pins for D1, D2, D3, A, RS232 and RS485.
A – Analog input pin. Analog voltage range 0-30 V.
TX – RS232 transmitted data (input).
RX – RS232 received data (output).
R- – RS485 receiver negative signal.
D- – RS485 driver negative signal.

HARDWARE INSTALLATION

Unscrew two back panel hex bolts and remove the back panel.
Insert your SIM card(s) into the SIM socket(s), which are located on the bottom side of PCB.
Attach the panel and tighten the hex bolts.
Attach the mobile antenna (max torque 0.4 NM / 3.5 liftin).
Connect open PSU leads to 16 pin terminal block:
a) red wire to top row ﬁrst contact (+);
b) black wire to bottom row ﬁrst contact (-).
Connect the 16 pin terminal block to gateway 16 pin connector and plug other end of the power adapter into a power outlet.

DEVICE CONFIGURATION

Power on the device and connect the Ethernet cable to your computer.
Allow the gateway to boot up. This might take up to 60 seconds.
To enter the gateway Web interface (WebUI), type http://192.168.1.1 into the URL ﬁeld of your Internet browser.
Use login information shown in image A when prompted for authentication.
After you log in, you will be prompted to change your password for security reasons. The new password must contain at least 8 characters, including at least one uppercase letter, one lowercase letter and one digit. This step is mandatory, and you will not be able to interact with the gateway WebUI until you change the password.
When you change the gateway password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool used to set up some of the gateway main operating parameters.
Go to the Overview page and pay attention to the Signal Strength indication (image B). To maximize the cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal conditions.

TELTONIKA TRB500 Industrial 5G Gateway - fig 6

TECHNICAL INFORMATION

Radio speciﬁcations

RF technologies	EGPRS, NB-IoT, LTE (Cat-M1), GNSS
Max RF power	33 dBm@GSM, 23 dBm@LTE

**Bundled accessories speciﬁcations***

Power adapter| Input: 0.4 A@100-240 VAC, output: 9 VDC, 1 A, connected to 16 pin terminal block
---|---
Mobile antenna| 698~960 / 1710~2690 MHz, 50 Ω, VSWR < 3, gain 3 dBi, omnidirectional, SMA male connector
GNSS antenna| 1575.42~1602 MHz, 2.2~5 VDC, VSWR < 1.5, gain 28 dB (typ.), RHCP polarization, SMA male connector

SAFETY INFORMATION

TRB255 gateway must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the communication module in prescribed applications and environments.
This sign means that all used electronic and electric equipment should not be mixed with general household waste.
This sign means that product meets the requirements of the applicable EU directives.

www.teltonika-networks.com
©2021 Teltonika Networks

Documents / Resources

| TELTONIKA TRB500 Industrial 5G Gateway [pdf] User Guide
TRB500, TRB255, TRB500 Industrial 5G Gateway, Industrial 5G Gateway, 5G Gateway, Gateway
---|---