NINGBO SP3598 BT Tumbler Speaker Instruction Manual

: June 4, 2024
: Ningbo

Table of Contents

NINGBO SP3598 BT Tumbler Speaker
FUNCTION PANELS
CHARGING
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NINGBO SP3598 BT Tumbler Speaker

FUNCTION PANELS

Box Includes: Tumbler Bluetooth* Speaker USB Type-C Charging Cable Instruction Manual

NINGBO-SP3598-BT-Tumbler-Speaker-fig-1- Bluetooth CONNECTION

Power the speaker on by long-pressing the power button for 2-3 seconds. The LED light will start to flash blue which indicates that you are now in Bluetooth pairing mode.
From your device’s Bluetooth menu, select “MV _SP3598” speaker.
When paired successfully, the device will confirm the connection has been made. Remember to turn the speaker off after each use.

Note : The speaker will reconnect automatically if your device has been paired previously. Depending on your device’s type and configuration, manual reconnection may be required each time.

CHARGING

It is recommended that the battery in the speaker be fully charged before initial use. This will take about 2 hours.
Using a USB-C cable (included), insert the USB-C jack into the port on the speaker and then plug the USB connecter into USB port on the power source.
While charging the LED indicator light will flash blue. Charge the device until the LED light turns off. Always disconnect the cable when charging is finished.

TROUBLESHOOTING

No power
Recharge your speaker using the USB Type-C cable. If the problem persists, try using another Type-C cable.

No response from the unit

Ensure your Bluetooth device supports an A2DP, AVRCP, or HFP profile.
Check if both devices are paired and connected to each other. Restart the device and try to reconnect.

FCC Disclaimer:
This device Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including Interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or on experienced radio/TV technician for help or assistance.

This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RS5 standard(s).

Operation is subject to thefollowing two conditions;

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Electronic and electrical device disposal
This symbol indicates that electrical and electronic device is to be collected separately. This product is designated for separate collection at an appropriate collection point. Do not dispose of as household waste.

If the device use batteries, they must be removed from the device and disposed in a appropriate collection center.
If the batteries cannot be removed, do not attempt to do it yourself since it must be done by a qualified professional.
Separate collection and recycling helps conserve natural resources and prevent negative consequence for human health and the environment that might result from incorrect disposal.
• For more information, contact the retailer or the local authorities in charge of waste management.