NINGBO LA-RC04 Remote Control Socket User Manual
- June 1, 2024
- Ningbo
Table of Contents
NINGBO LA-RC04 Remote Control Socket User Manual
SPECIFICATION
Model: LA-RC04
Remote control socket
Voltage: 125VAC, 60Hz
Max. load: 15A Resistive or General purpose, 10A/1250W Tungsten, 1/2HP
Remote
battery: 1PC CR2032 3V
Radio frequency: 433.92MHz
Operation distance: about 80 feet in open area.
For indoor use only.
OPERATION
-
Put battery in the remote.
Open battery cover of the remote and put 1PC CR2032 3V battery in it. Then press button of remote once to check whether it can work. If LED indicator turns on, it means this remote works well. -
Plug the timer into a GFCI protected receptacle. Press the remote control socket ON/OFF switch, and the power indicator light will light up.
-
Pairing with remote (remote function)
a. Press hold ON/OFF Switch for at least 5 seconds, Power indicator light of the Remote Control Socket is slowly flash. Enter into learning mode.(Please note: The timer will exit learning mode after 20 seconds without any operation).
b. Press ON button of the remote once to pair with the timer. Once successfully, LED indicator of the timer stops flash and keeps on.
c. Now you can turn on/off Remote Control Socket. Power indicator light of the timer turns on, it means power is on. In contrast, power is off. -
Clear the pairing
a. Press hold ON/OFF Switch for at least 5 seconds, Power indicator light of the Remote Control Socket is slowly flash, Enter into learning mode. Please note: The timer will exit learning mode after 20 seconds without any operation.
b. Press On/Off switch of the Remote Control Socket once to clear the pairing. Once successfully, LED indicator of the Remote Control Socket stop flashing
WARNINGS
Risk of Electric Shock
– Keep children away.
– Do not plug two or more timers together.
– Always ensure the plug of any appliance is fully inserted into the timer
outlet.
– If cleaning of the timer is required, remove from mains power and wipe timer
with a dry cloth.
– Do not immerse timer in water or any other liquid. Risk of Fire
– Don’t plug in an appliance where the load exceeds rated capacity.
– Do not use with extension cords.
– Do not use to control appliances that contain heating elements (cooking
appliances, heaters, irons, etc.).
CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help. The device
has been evaluated to meet general RF exposure requirement. The device can be
used in portable exposure condition without restriction.
ISED RSS Warning: This device complies with Innovation, Science and Economic
Development Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may
cause undesired operation of the device.
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. The device has been evaluated to meet general RF
exposure requirement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>