NINGBO DD7600 Series Handheld Emitter Instruction Manual
- May 15, 2024
- Ningbo
Table of Contents
DD7600 Series
Handheld Emitter Instruction
Version: A/03
Instruction Of Buttons
Technical specification
| Battery: 3V (AAA battery x2) | Battery life: >2 years |
|---|---|
| Working temperature: -10°C~+50°C | Radio range: 150 meters outdoor, 35 meters |
indoor
Radio frequency: 433.92MHz| Dimension: 144mm×45mm×14.8mm
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Warning
- Emitter couldn’t expose to moisture or be striked heavily, or else the emitter life will be affected.
- If the emitter is not so sensitive or the radio range becomes shorter, pls check whether to change the battery.
- It’s forbidden to use different type battery to avoid any dangerous risk.
- Dispose of used batteries properly.
Jog / Tilt Mode
Note: 1,The Jog up and Jog down buttons only control the channel where
the current transmitter is located,Release the button to send code.
2, This function is available in all series of transmitters. Following 2/3/4
only apply to emitters without LCD display
Enable / Disable Sun Detection
Note: 1, Press and hold the JOG DOWN button until the LED is on, the
operation is valid within 6 seconds, and press STOP button to exit the setting
directly.
2, The motor needs to be paired with wind-rain-sun sensor and only when the
motor has a limit, the sun detection function can be enabled and disabled.
Lock / Unlock Combo Button Operation
Note: 1,Both setting buttons (P2) can be operated.
2, The factory default is unlock status, repeat same operation to switch
status circulaly.
3, When the combo buttons are locked, if you press the combo buttons, the
emitter won’t send any signal and LED won’t flash.
Multi-limit Positions
(only valid for DD7660AH)
Note: 1, This operation takes 3rd limits(also as preferred position) as
an example, the operation of the 4th and 5th limit is same as the 3rd limit.
2, When the limit is set successfully, the motor will jog once.
3, The 4th and 5th limits can only be operated with the motor that supports
4th and 5th limits. Following 5/6/7/8/9/10 only apply to emitter with LCD
display
Enable / Disable Sun Detevction
Note: The motor needs to be paired with wind-rain-sun sensor and only
when the motor has a limit, the sun detection function can be enabled and
disabled. Lock / Unlock Combo Button Operation
Note: 1, Both setting buttons (P2) can be operated.
2, The factory default is unlock status, repeat same operation to switch
status circulaly.
3, Under lock status, the combo buttons don’t work; Under unlock status, the
combo buttons will work normally.
Set Number Of Channels
Note: In the setting status, press UP or DOWN button to exit quickly. Repeat the same process if you want to adjust the Max. channels.
Battery Check Function
Note: 1, Only the paired motor can check the battery and the current
channel can only check one paired motor.
2, Only the motors which are paired by long pressing STOP button for 2S will
have the battery check function.
Motor Percentage Running
Multi-limit Positions
(only valid for DD7662AH)
Note: This operation takes 3rd limits(also as preferred position) as an
example, the operation of the 4th and 5th limit is same as the 3rd limit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>