Golden Lighting 1945-SF Axel 4 Light Semi-Flush Ceiling Fixture Installation Guide
- June 4, 2024
- GOLDEN LIGHTING
Table of Contents
Golden Lighting 1945-SF Axel 4 Light Semi-Flush Ceiling Fixture
Product Information
Specifications:
- Model : 1945-SF
- Height : 8′
- Width : 30
- Weight : 5’9
- Voltage: 36
- Wattage : 28
Product Usage Instructions
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24 inches of island. Fixtures should hang at least 30 inches above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30 inches above the table. Use a fixture that is 12 inches narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors. -
Tips for Best Lighting:
To ensure the best lighting in your space, remember to layer your lighting for both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help meet your layered lighting needs.
Install the lights with dimmers to control the level of light output at any given moment.
Thank You for Choosing Us for Your Lighting Needs
-
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop. -
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table. -
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Assembly Instructions
How to Identify the Fixture’s Wires
Hot : Smooth, Black, or Transparent with Black Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by an accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap assembly from the parts bag.
Mounting strap (B) contains several threaded holes. Two sets of mounting
screws (A & C) should be attached to mounting strap (B). You may need to
tighten nuts (D) that hold mounting screws (A) in place. If the screws are not
attached, please hold canopy (F) up to mounting strap (B). Line up the holes
in canopy (F) with the holes in mounting strap (B) and insert mounting screws
(A) into mounting strap (B) so that mounting screws (A) protrude through the
holes in canopy (F). Mounting screws (A) are long, so please test the canopy
against the mounting strap to see how far you should insert the screws. Remove
the canopy and tighten nuts (D) onto mounting screws (A) to hold the screws in
place. 2. Place mounting strap (B) over the junction box and secure in place
with mounting screws (C). Tighten the screws securely with a screwdriver. Pull
house wires through the center of mounting strap (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting strap
and wrap the fixture’s ground wire around the ground screw. Use a screwdriver
to tighten the top of ground screw (E) onto the wires and into the mounting
bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Lift canopy (F) up to the mounting strap (B) so that the holes in the mounting
strap (B) line up with the holes in the canopy (F) and mounting screws (A)
protrude from the holes in the canopy (F). 5. Thread the decorative nuts (G)
onto the exposed threads of mounting screws (A) until canopy (F) is snug
against the ceiling. 6. Adjust the angle of rods (H) using Allen key (J) at
the notches depicted near the distributor. Unscrew the nut using the Allen key
(J) to loosen and adjust the position of the light. Tighten nut using Allen
key (J) to lock the position of the light and rods (H) in place. Install light
bulbs (not provided) into sockets (I) in accordance with the fixture’s
specifications. Do not exceed the maximum recommended wattage. Your
installation is now complete. Turn on the power and test the fixture.
FAQs
How do I identify the fixture’s wires?
The fixture wires are labeled as Hot, Neutral, and Ground. Match these with
the corresponding House Wires labeled as Hot, Neutral, and Ground.
What if I need replacement parts?
Contact the place of purchase for customer service to arrange for replacement
parts.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>