beper P201UTP201 ZEN Water Fountain User Guide
- June 3, 2024
- beper
Table of Contents
beper P201UTP201 ZEN Water Fountain
Precautions
Read the following instructions carefully, since they give you useful safety
information about installation, use and maintenance and help you avoid mishaps
and possible accidents.
Remove the packing and make sure that the appliance is intact, with special
attention to the supply cable.
The elements of the packing (plastic bags, polystyrene, etc) do not
have to be accessible to the children, in order to preserve them from danger
sources. It is recommended not to throw these packing material in the domestic
waste, but to deliver them to the appropriate station of collection or
destruction refusals, asking eventually information to the manager of the
Sanitation Department of your own municipality.
If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
Before connecting the appliance make sure that the mains voltage corresponds
to the data specified on the label.
The appliance can be damaged if the voltage is not correct.
If the plug does not suit the socket, let it be replaced with another suitable
plug by qualified personnel only, which shall also ensure that the section of
the socket cables is suitable for your appliance power absorption.
Generally, the use adaptors multiple plugs and/or extensions is not
recommended; should they be necessary, please use only simple or multiple
adaptors and extensions in compliance with the safety rules in force, making
sure that the capacity absorption limit marked on the simple adaptors and the
extensions and the maximum power limit marked on the multiple adaptor are not
exceeded.
Do not use the appliance if the cable or the plug shows any damages.
Do not use the appliance after a possible irregular working. In this case,
switch it off and do not break it open. Refer to an authorized Beper after-
sale service for repair and require original spare parts only. Failing to
follow these instructions may impair the safety of your appliance.
This appliance is to be destined to its special purpose only. Any other use is
to be considered as improper and thus dangerous. The manufacturer cannot be
responsible for any damages deriving from improper, wrong or incautious use.
This appliance is for household use only.
To protect against electric shock, do not immerse cord, plug or any parts of
the appliance into water or other fluids.
Do not use the appliance near explosives, highly flammable materials, gases or
burning flames.
Do not allow children, disabled people or every people without experience
or technical ability to use the appliance if they are not properly watched
over.
Close supervision is necessary when any appliance used by or near
children.
Some warnings
This appliance cannot be used by children, or persons with reduced physical,
sensitive or intellectual capabilities, or with lack of experience and
knowledge, without supervision or if they are not given instructions and
warnings on the correct and safe use of the device and the potential risks
related to its use.
Do not let children play with this appliance. Any cleaning and/or maintenance
operation cannot be carried out by children without proper surveillance.
Do not immerse the item (except for the pump) and its power cable in water or
other liquids.
This appliance is only intended for domestic use. Do not use outdoors.
Description of product Fig.A
- Decorative ball
- Top cover
- Base
- Pump
- Flow regulation switch
Assembling
Place the base on a flat and stable surface. Fill with water up to the rim, and place the top cover with the pump already installed on to the base, making sure that the pump is fully immersed and the small suction cups are attached to the bottom.
Important: it is better to use distilled water; in the long run, lime stone and mineral residues contained in tap water may, settle inside the pump, preventing its correct operation.
Place the decorative ball on top of the hole where water comes out, and the power cable inside the slot found on the back, making sure non to get the plug wet.
Operation
Make sure that the base is full of water and pump is immersed completely, then
connect the plug to a wall socket.
Water starts running continuously, to turn the appliance off it is necessary
to unplug it from the wall socket.
Note: if water is not running, there might be some air stuck inside the
pump circuit. Disconnect and re-connect the plug two or three times, until
water starts running.
Important: do not connect the plug to a wall socket without filling the
base with water, to avoid damaging the pump.
It is possible to adjust the water flow with the regulation switch found on
the pump; after disconnecting the plug from the wall socket, lift the top
cover to access the pump, by gently pull upwards to detach the small suction
cups, and slide the switch to the right or to the left to place it on the
desired flow level (4 levels available).
Replace the cover back on the base and connect the plug to the wall socket.
Cleaning and maintenance
The appliance doesn’t need any particular maintenance. Clean the outer surface of the top cover and of the base with a soft cloth slightly dampened (disconnect the plug from the wall socket before carrying out any cleaning or maintenance operation).
Technical data
Power: 3W
Power supply: 220-240V~ 50/60Hz
For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.
| The European directive 2011/65/EU on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances must not
be disposed of in the normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimize the recovery and recycling
of the materials they contain, and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on the product reminds you
of your obligation, that when you dispose of the appliance, it must be
separately collected.
---|---
GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original purchase a 24 month guarantee applies to material and production defects. The purchase receipt and the guarantee certificate must be submitted together in case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase (fiscal receipt) indicating the date of purchase and the model of the appliance
For any technical assistance, please contact directly the seller or our head office in order to preserve the appliance’s efficiency and NOT TO void the guarantee. Any intervention on this appliance by non-authorized persons will automatically void the guarantee.
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or production during the period of guarantee, we guarantee repair free of charge on condition that:
- The appliance has been used properly and for the purpose for which it has been intended.
- The appliance has not been tampered with, otherwise it is not maintainable.
- The purchase receipt shall be presented.
- The appliance showing a fair wear and tear shall not be covered by this guarantee.
Therefore, any part that could be accidentally broken or having visible signs
of use in consumable products (such as lamps, batteries, heating elements…)
the aesthetic parts are excluded from the guarantee, and any defect whatsoever
resulting from non-respect of the rules for use, negligence in usage and/or
maintenance of the appliance, carelessness, wrong or improper installation,
damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the
appliance will be replaced free of charge.
In any case, if the part to be replaced for defect, breakage or malfunction is
an accessory and/or a detachable part of the product, Beper reserves the right
to replace only the very part in question and not the entire product
Contact your distributor in your country or after sales department Beper.
E-mail assistenza@beper.com which will forward your enquiries to your distributor.
YOU MIGHT ALSO LIKE
Salt Stone Lamp
Cod.: P201UTP100
Natural Himalayan salt stone
Carved and processed by hand, unique and original shape
Easy mounting, removable lamp holder
Adjustable light intensity, thanks to the dimmer switch
Type E14 Lamp
15W
Aroma Diffuser
Cod.: P205DIF001
Ultrasound technology, safe and silent
Also suitable for essential oils
Adjustable timer with 4 available options:
continuous operation / 30 min / 60 min / 90 min
Auto shut off when water runs out
7 interchangeable colors LED light
BEPER SRL
Via Salieri, 30 – 37050 – Vallese di Oppeano – Verona
Tel. 045/7134674 – Fax 045/6984019
beper.com
Documents / Resources
|
beper P201UTP201 ZEN Water
Fountain
[pdf] User Guide
P201UTP201 ZEN Water Fountain, P201UTP201, ZEN Water Fountain, ZEN Fountain,
Water Fountain, Fountain
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>