EUROM LO80 Perfect Construction Dryer Instruction Manual

: June 3, 2024
: EUROM

Table of Contents

Symbol statement
Technical details
Important safety instructions
Eurom dehumidifier
Construction of the device
- Control panel
Starting and operating
Cleaning
Error messages and problem solutions
Disposal
Attachments
CE–declaration
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EUROM LO80 Perfect Construction Dryer Instruction Manual

Thank you

Thank you very much for choosing for a EUROM device. You have made a good choice! We hope you will be satisfied about its functioning.
To get maximum profit from your product, it is important to read this manual attentive and totally before use, and to understand what is written. Read especially the safety instructions: they are there to protect you and your environment.
Keep the manual in a safe place for future reference. Store also the package: that is the best protection for your product in times of no-use. And if you at any time pass the appliance on, pass on the manual and package too.

We wish you a lot of fun with the LO80!

This manual has been complied with the utmost care. Nevertheless, we reserve the right to optimize this manual at any time and to adjust it technically. The image used may differ.

Symbol statement

This appliance is filled with flammable Propane gas R290. Follow stricktly the manufacturer’s instruction concerning use and repairs!
Before using the machine, carefully read this entire instruction manual.
Do not install, operate or store the device in a room smaller than 14m².

Technical details

Connected power	220-240V~50Hz
Day dehumidification max.	80 L (30°C RH80%)
Output capacity	945 W
Cooling fluid	R290/0,30 kg
Power usage	4,2 A
Insolation class	IPX0
Dimensions	48 x 54 x 97 cm
Weight	53,5 kg

Important safety instructions

General

Please make sure the power supply is 220-240V~50Hz before operation.
Please do not plug or unplug to startup or shut off the device, but use the On/Offbutton.
Please do not cut off the power by pulling the wire, but take the plug in your hand.
Please be careful when moving the device, do not mangle the wire.
Please do not put finger, stick or other object into the grid.
Please prohibit child to climb, stand or sit on the device, or to touch it.
Please unplug the device before cleaning or maintenance.
If possible, do not use an extension cord, as this poses the risk of overheating and fire. If the use of an extension cord is unavoidable, then make sure it is an undamaged, approved extension cord with a minimum diameter of 3 x 1.5 mm² and a minimum permissible power of 1000 Watt/6 Amp. To prevent overheating, always fully extend the cord!
Do not use any relay, timer, dimmer or adapter. Otherwise, it might result in fire, radiation, or electric shock.
Do not use the device in sunshine, wind or rain; it is only to use indoors).
Do not use in places where chemicals or similar can be stored. Volatile substances can damage the device and cause leakage.
Keep clean the plug and plug it into the socket properly. If the plug is not properly plugged in, the result may be a shock or fire. Never touch device or plug with wet hands!
To prolong the life of the filter, pack it in a plastic bag when the device is not used for a longer time.
Do not place the equipment nearby a stove or heater; otherwise the weak parts may melt down and fire may be the result.
When problems arise (for example a strange smell) switch the device off immediately and unplug it from the wall outlet. Otherwise, a fire, an electric shock or malfunction may result.
Do not damage the electric cable and replace it never yourself. Do not place heavy objects on the cable and don’t lead it around sharp corners. Keep it away from heat sources. Don’t use a damaged electrical cable any more!
When the device is used continuously, arrange a suitable drain. Do not use the device at temperatures around or below freezing point.
Make sure that the machine is always in a stable and perfectly horizontal position.
Otherwise, water may enter into the device and get through to essential elements, with fire, shock, etc. to possible result.
Do not use the device near water or in spaces such as bathrooms and laundry rooms. If the device is too damp, fire or electric shock may occur.
When you don’t use the device for an extended period of time, disconnect the plug from the socket.
Repairs to the appliance, cord and plug must only be carried out by qualified technicians.

Safety in relation to coolant R290

This device contains the coolant R290. R290 is a coolant that complies with the relevant European Directives. Never perforate the coolant circuit. R290 is flammable (GWP 3)!
This device must be used and stored in a room that does not contain sources of ignition, such as open flames or gas and electrical devices in operation.
Do not perforate any of the components of the cooling circuit and do not set light to the device
If the device is installed, working or stored in an un-ventilated you must take measures to prevent fire or explosions caused by leaked coolant. Ensure that there are absolutely no sources of ignition (such as fire, heaters, sparking electrical equipment, lit cigarettes, etc.) in the same room!
The device must be stored in such a way that mechanical defects are prevented.
Do not install, operate or store the device in a room smaller than 14m².
R290 is odourless, which means that you cannot smell leaks!
Persons working on the cooling circuit must be in possession of the correct qualifications that state the person in question is competent to use coolant in accordance with a special evaluation that is recognised by the sector association.
The repairs must be executed on the grounds of the recommendations of the manufacturer of the device. Maintenance and repairs that require the assistance of other qualified persons must be executed under supervision of someone who is specialised in the use of flammable coolant.
Disassembly and recycling of the device must be performed by a certified technician.

Eurom dehumidifier

The Eurom dehumidifiers are designed to reduce the air humidity in a room and, as a result, raise levels of comfort and improve the conditions for the storage of goods.
The dehumidifier combines a practical design with top quality and simple controls. This makes it ideal for use in industrial, scientific and medical environments such as (underground) storage spaces, rooms that house technological equipment, archives and so on for the purposes of protecting computers, medicines, books etc. against moisture, erosion and mildew.

Construction of the device

Push bar
Control panel (display)
Filter
Air inlet
Air outlet (back side)
Wheel
Access to water collection tank + element

The water collection tank is equipped with a water discharge pipe, to which a 1/2 “hose must be connected via the side (by means of a hose clamp). Place the end of the hose in a well, drain or other waste water outlet. Ensure that the hose runs downwards without knicks.

Control panel

ON/OFF button
Humidity up button
Humidity down button
Humidity display
In operation symbol
Water collection tank full symbol
Defrosting symbol
Fan
Hour meter

Starting and operating

Make sure that the socket to which you want to connect the dehumidifier has the same voltage as stated on the rating plate: 220-240V ~ 50Hz.
Plug it into the socket; the device beeps.
Press the on / off button. The display shows the “operating symbol” and the current humidity. When the “in operation symbol” flashes, the humidity is lower than the set humidity.
Press the humidity up or humidity down button to set the percentage of the humidity.
Each time you press the humidity up and humidity down buttons, you set the desired humidity to 1% higher or lower. If the set humidity is more than 3% lower than the current humidity, the device starts operating until the current value is 3% lower than the set humidity. Then the device turns off.
If you set the humidity to less than 30%, the device will continuously dehumidify. The display will then show “CO”.
The appliance is equipped with an hour meter, which counts how many hours your appliance has worked in total (in units of 10 minutes).
Press the ON/OFF button again in order to switch the device off. The device will come to a halt and the display goes out.

Note:

If the set humidity is higher than the actual humidity, the device will not come on.
If you are dehumidifying, the fan motor and the compressor will run for at least three minutes before the compressor starts. The compressor may not be restarted within three minutes of switching the device off. It is, therefore, possible that the motor will not immediately respond to being turned off or on!
When the temperature is low, keep an eye on whether the device needs to defrost.
When defrosting, the relevant light will come on and the fan will run but the compressor will automatically switch off.
The devices have an automatic memory that automatically stores the settings and also saves if the power supply fails or is interrupted. Once the power supply has been restored, the device will start to work according to the previously entered settings.
The display will show a humidity level of 30% to 90%.
Remove the plug from the socket if you do not plan to use the device for an extended period.
If the water collecting tank is full, the light will come on and the compressor and fan will automatically shut down. You will also hear a beep. If you do not drain the water collection tank, the beep will be repeated every 5 minutes. Only once the water collection tank has been emptied can the device be used again.
You can install a continuous drain by removing the water collection tank, taking the rubber bung out on the side of the water collection tank and connecting a hose to this outlet. Then replace the water collection tank and run the hose from the device (downwards) to a suitable drainage point.
In order to avoid damaging the compressor, never place the dehumidifier on a slope of over 45°.
The device works between 5°C and 32°C.
When being used, the compressor will emit heat which can increase the ambient temperature by between 1 and 3°C. This is perfectly normal.
If the indoor temperature is lower than 10°C and air humidity is pretty low, you will not need to use the device.
Ensure that there is at least 10 cm of free space between the air inlet and the outlet opening and any solid objects, e.g. a wall.
Try to ensure that the room is as well sealed as possible in order to improve the dehumidification result.

Cleaning

Too much dust on the filter will impact upon the device’s ability to dehumidify. Clean the filter regularly (at least once a month); if the device is placed in a dusty environment, you should clean it weekly or even daily. To do so, open the front panel and take the filter (1) out. Remove the loose dust by carefully knocking the filter. Then vacuum the filter gently or wash it in lukewarm water with a little, mild soap. Leave to dry thoroughly before repositioning in the device (follow the above instructions in reverse order). Never use the dehumidifier without a filter! If also the element (2) is dirty, you can clean it carefully with a brush, see fig. The housing and the water reservoir can be cleaned with a damp cloth and a mild cleaning agent. Never use corrosive or abrasive products as these could damage the finish. Always remove the plug from the socket before carrying out any cleaning work!
Cleaning Induction

Error messages and problem solutions

Error messages
The following error messages could appear on the display:

E1: Problem in the humidity sensor
E2: Problem with the sensor for defrosting pipes

Problems and solutions The device does not work

Device is switched off – switch it on
Power failure – wait until power is restored
Plug not (correctly) inserted into socket – reinsert plug
Water reservoir full – drain it

The device is not dehumidifying very effectively

Filter blocked by dirt – clean filter
Obstacle in air inlet or outlet – remove blockage
Door or window open – close the door or window and shade the sun
Coolant leakage – contact a service department

Water leak

Device tips over – place on a stable and horizontal surface
Drain is blocked – remove blockage

Peculiar sounds

Device is not stable – place it on a stable and horizontal surface
Filter is blocked – clean filter

When you switch the device on or off, the circulation of the coolant can make a certain amount of noise; this is perfectly normal.
The air that is emitted from the air outlet may well be warm; this is perfectly normal.
If you cannot resolve the issue with the above instructions, please contact your supplier or a recognised repair company. Never open the device yourself!