EUROM 385793 Air Cooler Instruction Manual
- June 5, 2024
- EUROM
Table of Contents
EUROM 385793 Air Cooler
Thank you
Thank you very much for choosing for a EUROM device. You have made a good
choice! We hope you will be satisfied about its functioning.
To get maximum profit from your product, it is important to read this manual
attentive and totally before use, and to understand what is written. Read
especially the safety instructions: they are there to protect you and your
environment.
Keep the manual in a safe place for future reference. Store also the package:
that is the best protection for your product in times of no-use. And if you at
any time pass the appliance on, pass on the manual and package too.
We wish you a lot of fun with the Air cooler!
Eurom
Kokosstraat 20
8281 JC Genemuiden (NL)
info@eurom.nl
www.eurom.nl
This manual has been complied with the utmost care. Nevertheless, we reserve
the right to optimize this manual at any time and to adjust it technically.
The image used may differ.
Instruction (Symbol statement) topping up the water tank
- Switch off humidification and cooling function
- Switch off the on and off button
- Remove the plug from the socket
- Allow the device to rest for 5 minutes
- Fill the tank with a maximum of 2.25 liters of water
- If desired, plug in again and switch on ventilation, cooling and humidification function.
Read the instructions for use for the cleaning instructions.
Technical data
| Supply voltage | 220-240V~50Hz |
|---|---|
| Input power | 65 Watt |
| Capacity water tank | 2,25 liter |
| Dimensions | 19 x 32 x 67,5 cm |
| Weight | 6 kg |
General safety instructions
-
Read this instruction booklet carefully and completely before use.
-
Check your device (incl. Cable and plug) for visible damage before use. Do not use a damaged device, but offer it to your supplier for replacement.
-
Remove the plug from the wall socket and immediately switch off the air cooler when you hear strange noises, smell or see smoke.
-
This device is intended for normal household use only indoors.
Use this device only for the purpose for which it was designed (cooling / ventilating a household space) and in the manner described in this booklet. -
This device is not suitable for use in wet or damp areas such as bathrooms, washrooms, etc. Do not place it in the vicinity of a tap, bathtub, shower, swimming pool, wash basin or similar, make sure it can never fall into water and prevent water enters the device. Should the device ever fall into water, first remove the plug from the socket! Stop using an internally wet device but offer it for repair. Never immerse the device, cord or plug in water or other liquid and never touch the device with wet hands.
-
Connection voltage and frequency (220-240V ~ 50Hz) stated on the device must correspond to that of the socket to be used. The electrical installation must be protected with an earth leakage circuit breaker (max. 30 mA).
-
Fully unwind the electrical cable before plugging in and ensure that it does not get hot anywhere. Do not route the cable under carpet, do not cover it with mats, runners or similar. and keep the cable outside the walking route. Make sure that you do not step on it and that no furniture is placed on it. Do not route the cable around sharp corners and do not wind it too tightly after use!
-
The use of an extension cord is not recommended. If the use of an extension cord is unavoidable, ensure that there is an undamaged, approved extension cord of sufficient thickness. Always unwind the cord completely to prevent overheating!
-
Do not store or use the device:
- In places where it can get wet or fall into water
- Near highly flammable, explosive or gaseous substances. A spark from the switch could do that ignite.
- Near acids, alkali, oil and other substances that can cause corrosion.
-
Always place the device on a dry, stable, horizontal and level surface.
-
Do not place the device directly under a power outlet.
-
Do not place objects on the device or sit on them.
-
Ensure that the air supply and air discharge are not obstructed by blockages. Do not place anything on or over the device and do not place the device too close to walls, curtains, furniture, etc. Impediment of the air supply and air discharge can affect the operation and service life!
-
Keep the suction and discharge grille clean and dust-free and ensure a minimum of 30 to 50 cm free space around the air cooler.
-
To avoid moisture in the electrical part, do not touch, move or move the device and do not tilt it. If water accidentally enters the electrical part, immediately remove the plug from the socket and remove the water as well as possible. Allow the device to dry for at least 24 hours. Keep an eye on the device when you start using it again. If abnormal behavior or noise is detected, immediately unplug the power cord and have the device checked / repaired by a qualified electrician.
-
Replace the water regularly, especially in hot weather, to prevent contamination. Remove the remaining water from the device in case of frost!
-
Do not fill the water tank above the “MAX” level; for “cooling”, the water must be above the “MIN” level. Ensure that the plug does not get wet or fall into the water tank. Never use a cooling function without sufficient water in the water tank. Use only cold water, not warm or warm water.
-
Do not use the “cooling” function in a confined space that is too small.
-
Always remove the plug from the wall socket when the device is not in use.
-
Do not leave a working air cooler in a room unattended.
-
Never put a finger, pen, stick or anything else through the openings of the device. Prevent foreign objects from entering the device through the openings. This can cause injury, an electric shock, fire or damage.
-
Do not spray any agents (anti-insect, cleaning or whatever) on or in the air cooler; this can cause physical complaints (in particular with children!) or damage to parts.Do not turn on the appliance if you have discovered damage to the appliance, cord or plug, if the appliance is malfunctioning, if it has been dropped or if there are signs of any other defect. Return the complete product to the vendor or to a certified electrician for inspection and/or repair. Always ask for original parts.
-
Do not knock or shake on a working device! Always switch the device off and remove the plug from the socket when:
- want to top up water
- want to clean the device
- want to carry out maintenance on the device
- moved the device.
-
Do not operate the device automatically by using. a time clock
- i.d. Always check for safe conditions before use! Do not connect the air cooler to a dimmer.
-
Do not use the air cooler at temperatures above 40 degrees Celsius, near heating equipment and in dusty areas.
-
Ensure proper supervision when this device is used in the presence of children, incapacitated persons or pets. This device can be used by children 8 years of age and older and persons with reduced physical, sensory or mental skills or lack of experience and knowledge when supervised or when they have received instructions on how to use the device safely. and understand the dangers involved. Children must not play with the device. Cleaning and user maintenance must not be carried out by children without supervision.
-
Remove the water and dry the tank when you are not going to use the device for a long time, before winter storage or before you transport it. This is to prevent moisture evaporation and odors.
-
Prevent the device from constantly blowing on small children, patients or people who have difficulty moving.
-
Do not operate the device if you notice any damage to the device, electrical cable or plug, or if it malfunctions, has been dropped or otherwise malfunctions. Return the complete device to your supplier or an authorized electrician for inspection and / or repair. Always ask for original parts.
-
The device (incl. Electrical cable and plug) may only be opened and / or repaired by authorized and qualified persons. If the electrical cable or plug is damaged, it must be replaced by a qualified person. Never carry out repairs yourself.
-
Use the device only for the purpose for which it was designed and in the manner described in this booklet.
Deviations from 29, 30 & 31 can cause damage, fire and / or personal injury. They invalidate the warranty and the supplier, importer and / or manufacturer accept no liability for the consequences!
Description
- Operation panel
- Air outlet
- Handle
- Back cover
- Front panel
- Back cover
- Water reservoir
- Water gauge
- Electrical cable with plug
- Water reservoir clip
- Air inlet
The Air-cooler evaporates water with heat that is removed from the room and
sends the cool, humid air back into the room: a process that can be compared
to wind blowing across water.
The Air cooler has the following functions:
Cooling: cools air by evaporating water, even in a damp or windy space.
Air humidification: the evaporated water humidifies air in the room.
Air cleansing: a functioning unit filters fine particulates, fibers etc.
and also air pollution and nicotine from the air and thus helps create a clean
and healthy environment.
Ionization: removing ions from the air makes it extra clean and also
increases the oxygen level; this is beneficial for heart and lung functions,
resistance to disease, sleep and so on.
Swiveling : the cooled air can be emitted horizontally over a 120° angle.
The vertical direction can be set manually.
Fan: the fan can be set at a range of ventilation types and speeds.
Remote control: the unit can be operated using the remote control from 6
meters away and within an angle of 120°.
The device is energy efficient and only uses water for cooling purposes: it
uses no chemical agents and is therefore environmentally-friendly. The unit is
easy to clean.
Installation and preparation
- Place the unit straight, on a sturdy, flat and horizontal surface. Ensure there is sufficient space at the front (air outlet) and sides (air inlet). The back of the unit may rest against a wall, if necessary.
- Check whether the socket that you wish to use provides the required voltage, as detailed on the specification plate.
- Pull the water reservoir roughly 10 cm backwards and fill with clean water; do not exceed the ‘MAX’ level! It is recommended that the tank is filled with ice-cold water and to add any ice cubes or a frozen cooling for even better performance.
- If you have not used the unit for some time, refresh any remaining water.
- If you wish to use the humidification function, ensure there is sufficient water in the reservoir.
Note: If you want to fill the water reservoir, always switch off the appliance and wait a few minutes. See further at Installation and Preparations.
Operation
Insert the plug into the socket. The unit is now ready for use.
- Start the unit by pressing the ON/OFF button. Pressing it again will stop the unit.
- By pushing the Cool button, you start the cooling function. The pump circulates water from the reservoir via the water curtain, where it partially evaporates, thus ensuring cooling. By pushing this button again, the function is disabled again.
- Pressing on the Speed button allows you to choose a ventilation speed; you select a different speed each time you press: L (low) – M (medium) – H (high). The corresponding light will then come on.
- Pressing on the Mode button allows you to select a method of ventilation; you can set the speed using the ‘speed’ button.
- Normal – gives a regular breeze
- Natural – gives a natural, irregular breeze
- Sleep – gives a natural, irregular breeze that switches to low speed, irrespective of the fan speed setting, after half an hour.
- The Swing button makes the breeze swivel from left to right horizontally; the corresponding light will come on. Pressing it again switches this function off. By adjusting the horizontal panels manually, you can adjust the vertical outlet direction.
- Pressing the Humidify button when the unit is on will switch on the humidification function; the corresponding light will then come on. Pressing it again switches this function off.
- Pressing the Ion button will switch the anion generator on; the corresponding light will come on. Pressing it again switches this function off.
- Pressing the Timer allows you to set the required time: each press on the button gives a further half hour, until max. 7.5 hours. Pressing it again switches this function off. The lights indicate the set time.
When using the stove for the first time, the honeycomb filter might give off an odor. This disappears eventually. To accelerate this process, rinse the honeycomb filter with clean water before using it and dry it before placing it back. You might have to repeat this several times.
Remote control
Install 2 AAA batteries in the section at the back of the remote control. You
can now operate the unit from a distance of max. 6 meters. The buttons on the
remote control correspond with those on the operating panel. The receiver is
positioned on the top left hand side of the operating panel; always point the
remote control in this direction.
Remove the batteries if the device is not going to be used for some time.
Cleaning and maintenance
Switch off the equipment and remove the plug from the socket before cleaning or carrying out maintenance work.
- Wipe the outside of the equipment regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays, cleaners or abrasives, waxes, polishes or chemical solutions! Ensure that the operating panel does not get wet.
- Use a vacuum cleaner to carefully remove any dust and dirt from the grills and ensure that the air intake and outlet openings are clean. Be careful not to touch or damage any internal parts during cleaning!
- In order to avoid the creation of odors and ensure the unit works properly, it must be cleaned internally once every two weeks.
- Remove the front panel by loosening the two attachment pins and lifting the panel upwards, off the 2 upper attachment points. Remove the filter and the honeycomb filter from the unit.
- Wash the filter in warm water with a mild, soapy solution; use a soft brush if necessary. Rinse with clean water and leave to dry.
- Wash the honeycomb filter with clean water and a soft brush if necessary. Leave to dry.
- Empty the water tank and clean with water, a mild soapy solution and a soft brush if necessary. Rinse with clean water and leave to dry.
1 = front panel 2 = filter 3 = honeycomb-filter
- At the end of the season, store the cleaned and dried heater in the original packaging if possible. Store it upright in a cool, dry and dust-free place.
Never let water sit in the water tank or casing for longer than a few days.
Change it/throw it away; rinse the tank and let the aircooler dry if you are
not planning to use it for a while.
Problems and solutions
The device does not work
- No electricity. Check to ensure the plug is in the socket and that the socket is live.
- Is the ON/OFF button pressed in?
- An internal electrical component is broken. Consult your supplier or an electrician.
The unit will not switch off
- Is the ON/OFF button pressed in?
- An internal electrical component is broken; consult your supplier or an electrician.
Peculiar sounds
-
Something is not positioned correctly inside the machine. Remove the filters and the water reservoir and install correctly.
-
A swivel wheel is broken/missing; consult your supplier.
-
There is an internal problem; consult your supplier.
The unit humidifies too much or too little -
Filters are blocked by dirt; clean filters
-
Technical breakdown; consult your supplier.
For other breakdowns, you must consult your supplier.
Removal
In the EU this symbol indicates that this product may not be disposed of as ordinary household waste. Old equipment contains valuable materials, suitable for recycling. These materials should be made suitable for reuse in order to prevent any adverse effects to health and the environment caused by unregulated waste collection. Therefore, please make sure that you bring old equipment to a designated collection point. Alternatively, contact the original supplier, who can make sure that as many of the components as possible can be recycled.
CE – Declaration
Eurom bv., Genemuiden-NL hereby declares that the electrical air cooler, brand
EUROM, type AIRCOOLER complies with the LVD guideline 2014/35/EU and the EMC
guideline 2014/30/EU and meets the following standards:
EN 60335-1:2012+A11:2014+A13:2017
EN 60335-2-80:2003+A1:2004+A2:2009
EN 60335-2-98:2003+A1:2005+A2:2008
EN 62233:2008
EN 55014-1:2017
EN 55014-2:2015 EN 61000-3-2:2014
EN 61000-3-3:2013
RoHS 2011/65/EU &(EU)2015/863
Genemuiden, 07-10-2021
W.J. Bakker, alg.dir.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>