signify Day Brite LED High Bay Industrial Linear Installation Guide

: June 1, 2024
: signify

Table of Contents

INSTALLATION
SAVE THESE INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

signify Day Brite LED High Bay Industrial Linear Installation Guide

INSTALLATION

WARNINGS AND INSTRUCTIONS FOR LUMINAIRES

IMPORTANT: FOR YOUR PROTECTION, YOU MUST CAREFULLY READ ALL WARNINGS AND INSTRUCTIONS IN THEIR ENTIRETY PRIOR TO INSTALLATION, OPERATION, SERVICE, OR MAINTENANCE. FAILURE TO DO SO CAN RESULT IN DEATH, PERSONAL INJURY AND PROPERTY DAMAGE. If you do not understand these warnings and instructions, or if additional information is desired, please contact the Customer Care Call Center at 800 555-0050.
Installation, service, and maintenance of luminaires must be performed by a qualified professional and in accordance with all federal, state, and local laws, regulations, and electrical codes. This professional should be familiar with the construction and operation of this product and any hazards involved. If not qualified, do not attempt installation, service or maintenance.
To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts, abrasions, and other hazards, please read all warnings and instructions included with the luminaire, on the luminaire’s packaging and affixed to the luminaire itself.
Maintenance of the luminaires should be performed by person(s) familiar with the luminaire’s construction and operation and any hazards involved.

WARNING

RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Disconnect or turn off power before attempting any installation, service or maintenance.
Verify that supply voltage is correct by referencing the luminaire label information.
Make all electrical and ground connections in accordance with the National Electrical Code (NEC) and any other applicable laws, regulations, or codes.
All wiring connections should be capped with UL-approved wire connectors.

WARNING
RISK OF PERSONAL INJURY

Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
Avoid direct eye exposure to the light source while it is on.

WARNING
RISK OF PERSONAL INJURY

Keep combustible materials away from LED/lamp & lens.
Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.

WARNING RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY

Allow LED/lamp & lens to cool before handling.
Do not touch enclosure or light source.
Do not exceed maximum wattage marked on luminaire label.
Follow all manufacturer’s warnings, recommendations, instructions, and restrictions for driver type, burning position, mounting locations and replacement.

CAUTION
RISK OF PRODUCT DAMAGE

Never connect luminaires and/or components under load with supply voltage turned on.
Do not mount or support these luminaires in a manner that can cut the outer jacket or damage whe insulation
Do not restrict fixture ventilation. Allow for some volume of airspace around the luminaire. Avoid covering the luminaire with insulation, foam, or other material that will prevent convection or conduction cooling
Do not exceed luminaire maximum ambient temperature
Do not modify the luminaire
Only use luminaire in its intended application and location.
LED products are polarnity sensitive. Ensure proper polarity before installation.
Electrostatic Discharge (ESD) can damage LED. Personal grounding equipment must be worn during all installation and servicing of the luminaire.
Do not touch individual electrical components as this can cause ESD, shorten LED life, or impact LED performante.
Some components inside the luminaire may not be serviceable, in the unlikely event, your luminaire may require service, stop using it immediately and contact the Customer Care Call Center at 800-555-0050
Always read the luminaire’s complete installation instructions prior to installation for any additional luminaire-specific warnings.
In the case of HID or fluorescent luminaires, regular re-lamping is required to keep the luminaire operating within safe limits.
Do not install damaged products. Handling and installing damaged products can potentially increase the risks mentioned, in case of damage and/or missing parts upon anival of the luminaire, please contact the Customer Care Call Center at 800-555-0050.
These instructions do not purport to cover all details or vanations in equipment nor to provide every possible contingency to meet in connection with installation, speration or maintenance. Should further information be desired, or should particular problems anse which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be refered to the Customer Care Call Center at 800-555-0050.
Please see luminaire specific Installation and Maintenance Instruction for additional warnings or any applicable FCC or regulatory statements. Fallure to follow any of these instructions could void luminaire warranties.

Luminaire Maintenance

Regular luminaire maintenance programs are recommended.
It is recommended to clean the outside of the luminaire and the refractor/lens.
Frequency of cleaning will depend on ambient dirt level and minimurn light output which is acceptable to the user.
If clean water is not sufficient for cleaning, use a neutral, synthetic, non-scratching, and non-abrasive cleaning substance.
Never use alkaline and/or acetous cleaning substances.
Make sure that the cleaning substance is carefully removed by rinsing with lots of clean water.
Signify recommends using a cleaning solution that has a PH between 5 and 8.
Recycle: For information on how to recycle electronic products and components, please visit www.epa.gov.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to port 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and con radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not accur in a particular installation. If this equipment does couse hormful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Wiring Diagram

For dimming wires, use class 1 wiring methods.
Cap dimming wires (separately) if not used.
Cap Emergency wires (separately) if not used

SAVE THESE INSTRUCTIONS

CAUTION: Electrical luminaires are designed for permanent installation in ordinary (non-hazardous) locations in accordance with the National Electrical Code and all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible materials can cause fire and personal contact can cause severe burns

CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL.

Read all instructions before starting installation.
This product must be installed in accordance with the applicable installation codes by a qualified electrician familiar with the construction and operation of the product and the hazards involved.
Disconnect power at circuit breaker of fuse before starting installation.
To avoid injury, wear gloves during installation.
To reduce the risk of electrical shock and product damage, do not install this luminaire during rain or other storms.
Do not test luminaire using an electric generator before installation

Instructions

Chain Mount:(included)
To suspend the highbay luminaire from chains, attach the enclosed vhooks to the holes on the end caps. Attach the chain to a secure, stationary structure, and use the spring clips on the end to attach the chain to the v-hooks. Choose the appropriate knock out, and wire the fixture in accordance with proper code . (Figure 1)

Pendant Mount:(purchase separately)
To pendant mount the highbay luminaire, mount the fixture brackets to 3/4”NPS **(Figure 1).

Once the brackets have been properly secured, attach the fixture using the screws provided (Fixture 2** ).
Assembly Instructions
Choose the appropriate knockout, and wire the fixture in accordance with proper code. Secure the cover plates to the bracket using the screws provided.

Surface Mount:(purchase separately)
To surface mount the highbay luminaire, bolt the fixture brackets to the ceiling or rail (Figure 1).
Assembly Instructions
Once the brackets have been properly secured, attach the luminaire using the screws provided (Figure 2).

Choose the appropriate knockout, and wire the fixture in accordance with proper code.

CAUTION: Electrical luminaires are designed for permanent installation in ordinary (non-hazardous) locations in accordance with the National Electrical Code and all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible materials can cause fire and personal contact can cause severe burns.

Motion Sensor/PIR Sensor: (purchase separately)
To install motion/PIR sensor, remove threaded plug/cover from the sensor receptacle using a flat screwdriver (Figure 1 and 2)
Assembly
Instructions
then mount the sensor on the sensor receptacle (Figure 3).

Wire Guards: (purchased separately)
To attach wire guards to luminaire, aligh the holes on the wireguard with the holes on the end caps and secure using screws provided with the wire guard kit
Assembly Instructions

CCT & Lumens Tunable

Remove switch cover and slide switches to desired lumens and CCT
Default factory setting is 4000K at highest lumens output

For gymnasium or other impact applications.
After mounting the V-hooks, mount the 3 inch screws provided on the same slot for the V-hooks. Position the screws to capture the V-hooks tightly against the top of the slot.
Do not overtight

© 2024 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify. All trademarks are owned by Signify Holding or their respective owners.

Signify North America Corporation 400 Crossing Blvd, Suite 600 Bridgewater, NJ 08807, USA
Signity Canada Ltd. 281 Hillmount Rod Markham. ON. Canada L6C 253 Telephone 800-6-9006