Sinum R-S1 Room Regulator Instruction Manual

: June 1, 2024
: Sinum

Table of Contents

Sinum R-S1 Room Regulator
Introduction
Opis
How To Register The Device In The Sinum System
How To Identify The Device In The Sinum System
Operation
Menu
Technical Data
Important Notes
EU Declaration of Conformity
Service
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sinum R-S1 Room Regulator

Sinum-R-S1-Room-Regulator-Product

Introduction

The R-S1 room regulator is equipped with a temperature and air humidity sensor.
Current measurements are displayed on the device and sent to the Sinum Central device, where they can be freely used to create various automation.
Communication with the Sinum Central device is done by wire. The regulator is mounted to an electrical box with a diameter of 60 mm.

Opis

Registration button
Main button
Navigation buttons
SBUS communication connector
Terminating resistor

$Sinum-R-S1-Room-Regulator-Fig- $1$$ $Sinum-R-S1 -Room-Regulator-Fig- $2$$

How To Register The Device In The Sinum System

The device should be connected to the Sinum central device using the SBUS connector 4 , and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > + > Add device. Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.

INFO: When registering the regulator, the humidity sensor will also be registered automatically.

How To Identify The Device In The Sinum System

To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab and hold the registration button on the device for 3-4 seconds. The device used will be highlighted on the screen.

Operation

Heating/cooling control * (icon ) is possible after assigning the controller in the Sinum Central device to a virtual thermostat. On the display, the icon can have different meanings:
- the icon is on permanently – heating of the room (heating mode)
- the icon is blinking – room cooling (cooling mode)
- no icon – no need for heating/cooling
Changing the preset temperature with the + and – buttons and confirming with the Menu button . The set temperature will be permanent. If the regulator is assigned to a virtual thermostat, after changing the temperature, use the + and – to specify the time range of the set temperature [0 ÷ 24h, Con (permanently) or Off (inactive change)], and confirm with the Menu button .
Controller connection – the system has a terminating connection. The position of the regulator on the transmission line with the Sinum Central is determined by the position of the terminating switch 5. Set to ON position (regulator at the end of the line) or position 1 (regulator in the middle of the line).
option available depending on the program version

Hold down the Menu button until the appears option. change options with + and – , confirm with Menu button. Options available:

– temperature sensor calibration,
– activation/deactivation of the button lock; to unlock, hold down the + and – buttons simultaneously for 3 seconds,
– device registration,
– software information,
– factory reset,
– exit from the Menu,

Technical Data

Power supply	24V DC ±10%
Max. power consumption	0,2W
Operation temperature	5 ÷ 50°C

Important Notes

TECH Controllers is not responsible for any damages resulting from improper use of the system. The range depends on the conditions in which the device is used and the structure and materials used in the object construction. The manufacturer reserves the right to improve devices and update software and related documentation.

The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.

The product may not be disposed of in household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.

EU Declaration of Conformity

Tech Sterowniki II Sp. z o.o. , ul. Biała Droga 34, Wieprz (34-122) Hereby, we declare under our sole responsibility that the room regulator R-S1 is compliant with Directive:

2014/35/UE
2014/30/UE
2009/125/WE
2017/2102/UE

For compliance assessment, harmonized standards were used:

PN-EN IEC 60730-2-9:2019-06
PN-EN 60730-1:2016-10
EN IEC 63000:2018 RoHS

Wieprz, 01.07.2023

The full text of the EU Declaration of Conformity and the user manual are available after scanning the QR code or at www.tech- controllers.com/manuals.

www.techsterowniki.pl/manuals
Wyprodukowano w Polsce

www.tech-controllers.com/manuals
Made in Poland

$Sinum-R-S1-Room-Regulator-Fig- $14$$