Sinum PS-08m 230 DIN Rail Relay Blue User Manual

: June 16, 2024
: Sinum

Table of Contents

PS-08m 230 DIN Rail Relay Blue
Description
Manual mode
How to register the device in the sinum system
How to identify the device in the Sinum system
Technical data
EU Declaration of conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Sinum PS 08m 230 DIN Rail Relay Blue - cover

PS-08m 230
www.sinum.eu

PS-08m 230 DIN Rail Relay Blue

Service

tel: +48 33 875 93 80 www.tech-controllers.com
support.sinum@techsterowniki.pl

Sinum PS 08m 230 DIN Rail Relay Blue - qr 1

www.techsterowniki.pl/manuals

www.tech-controllers.com/manuals

Made in Poland

The PS-08m 230V module is an electronic device dedicated for underfloor heating system. It is equipped with 8 independent voltage relays enabling the user to control 8 independent devices. It is designed to be mounted on a DIN rail.
Communication with the Sinum central device is done by wire.

Description

– Power supply
– Communication
1-8 – Current status of the voltage output (ON/OFF)

Manual mode

In order to switch to the manual operation mode, press the manual operation button 1 . The registration button 2 is used to switch between the controlled outputs in the manual mode. Using the button 1 (pressing it once), the user forces a change of the status (ON / OFF) – if the process has been successful, it is confirmed by a light signal from the LED labelled 1-8. When the manual mode is on, it is impossible to control the contact via the website or the application. To disable the manual mode, press the button 1 again and hold it for 1-2 seconds. Once the manual mode has been switched off, all the output status LEDs go off and resume the state set in the Sinum application.

How to register the device in the sinum system

The device should be connected to the Sinum central device using the SBUS connector 3 , and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > > Add device. Then briefly press the registration button 2 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room.
For control underfloor heating system, virtual thermostats must be created.

How to identify the device in the Sinum system

To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > > Identification Mode tab and hold the manual operation button 1 on the device for 3-4 seconds. The device used will be highlighted on the screen.

Technical data

Power supply	230V ±10% /50Hz
Max. power consumption	4,5W
Potential contacts 1-8 max. output load	0,5A
Operation temperature	5°C ÷ 50°C
Acceptable ambient relative humidity	<80% REL.H

Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The range depends on the conditions in which the device is used and the structure and materials used in the object construction. The manufacturer reserves the right to improve devices, update software and related documentation.
The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website.
Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.

The product may not be disposed of to household waste containers.
The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled.

EU Declaration of conformity

Tech Sterowniki II Sp. z o.o. ul. Biała Droga 34, Wieprz (34-122)
Hereby, we declare under our sole responsibility that the modul PS-08m 230 is compliant with Directive :