TECH Sinum R-S2 Przewodowy Regulator Temperatury R-S2 User Manual

: June 13, 2024
: TECH Sinum

Table of Contents

TECH Sinum R-S2 Przewodowy Regulator Temperatury
Opis
How to register the device in the sinus system
How to identify the device in the Sinum system
Operation
Menu
Technical data
EU Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TECH Sinum R-S2 Przewodowy Regulator Temperatury

The R-S2 room regulator is equipped with a temperature and air humidity sensor. Current measurements are displayed on the device and sent to the Sinum Central device, where they can be freely used to create various automation. Communication with the Sinum Central device is done by wire. The regulator is mounted to an electrical box with a diameter of 60 mm.

Opis

Registration button
Main button
Navigation buttons
SBUS communication connector
Terminating resistor

How to register the device in the sinus system

The device should be connected to the Sinum central device using the SBUS connector 4, and then enter the address of the Sinum central device in the browser and log in to the device. In the main panel, click the Settings > Devices > SBUS devices > + > Add device. Then briefly press the registration button 1 on the device. After a properly completed registration process, an appropriate message will appear on the screen. Additionally, the user can name the device and assign it to a specific room. INFO: When registering the regulator, the humidity sensor will also be registered automatically.

How to identify the device in the Sinum system

To identify the device in the Sinum Central, activate the Identification Mode in the Settings > Devices > SBUS Devices > + > Identification Mode tab and hold the registration button on the device for 3-4 seconds. The device used will be highlighted on the screen.

Operation

Heating/cooling control * (icon ) is possible after assigning the controller in the Sinum Central device to a virtual thermostat. On the display, the icon can have different meanings:
- The icon is on permanently – heating of the room (heating mode)
- The icon is blinking – room cooling (cooling mode)
- No icon – no need for heating/cooling
Changing the preset temperature with the buttons and confirming with the Main button
The set temperature will be permanent. If the regulator is assigned to a virtual thermostat, after changing the temperature, use the and to specify the time range of the set temperature [0 ÷ 24h, Con (permanently) or Off (inactive change)], confirm with the Main button
Button lock – pressing the Main button will activate the function ;
Use the or to select „yes” or „no” (automatic lock on/off). Confirm with the Main button or wait approx. 5 sec. Holding simultaneously until the padlock icon disappears unlocks the buttons .
Controller connection – the system has a terminating connection. The position of the regulator on the transmission line with the Sinum Central is determined by the position of the terminating switch 5 set to ON position (regulator at the end of the line) or position 1 (regulator in the middle of the line).

option available depending on the program version

Technical data

Power supply 24V DC ±10%
Max. power consumption 0,2W
Operation temperature5 ÷ 50°C

Notes
TECH Controllers is not responsible for any damages resulting from improper use of the system. The manufacturer reserves the right to improve devices, update software and related documentation. The graphics are provided for illustration purposes only and may differ slightly from the actual look. The diagrams serve as examples. All changes are updated on an ongoing basis on the manufacturer’s website. Before using the device for the first time, read the following regulations carefully. Not obeying these instructions may lead to personal injuries or controller damage. The device should be installed by a qualified person. It is not intended to be operated by children. It is a live electrical device. Make sure the device is disconnected from the mains before performing any activities involving the power supply (plugging cables, installing the device etc.). The device is not water resistant.

The product may not be disposed of in household waste containers. The user is obliged to transfer their used equipment to a collection point where all electric and electronic components will be recycled

EU Declaration of Conformity

Tech Sterowniki II Sp. z o.o. , ul. Biała Droga 34, Wieprz (34-122) Hereby, we declare under our sole responsibility that the room regulator R-S2 is compliant with Directive :

2014/35/UE
2014/30/UE
2009/125/WE
2017/2102/UE

For compliance assessment, harmonized standards were used

PN-EN IEC 60730-2-9:2019-06
PN-EN 60730-1:2016-10

EN IEC 63000:2018 RoHS

The full text of the EU Declaration of Conformity and the user manual are available after scanning the QR code or at www.tech- controllers.com/manuals

Made in Poland
tel: +48 33 875 93 80 www.tech-controllers.com
support.sinum@techsterowniki.pl