kikka boo i-Felix Car Seat Instruction Manual

kikka boo i-Felix Car Seat

Specifications

• Model: i-FELIX car seat
• Size: i-Size
• Height Range: 40-150cm

Installation

Follow these steps to install the child restraint system:
Ensure the car seat has ISOFIX anchorages, top tether points,  and a lap and 3-point belt.

1. Do not install in front seats unless specific conditions are met (as outlined in the manual).
2. Secure the child restraint system according to the provided instructions.

Buckle and Strap Adjustment
Properly buckle and adjust the straps for optimal safety and comfort:

1. Buckle using the provided steps to ensure a secure fit.
2. Adjust the length of the straps for a snug but comfortable fit.
3. Check and adjust the strap tightness each time the child is placed in the seat.

ISOFIX Adjustment and Seat Angle
Make sure to correctly adjust the ISOFIX and seat angle for proper installation and comfort:

1. Press the red ISOFIX release button to adjust the ISOFIX position.
2. Use the red angle adjusting lever to set the desired seat angle= for comfort.

FAQ
Q: Can I install this car seat in the front seat?
A: The car seat should not be installed in the front seat unless specific conditions are met. Refer to the manual for more details.

 IMPORTANT! KEEP FOR FUTURE REFERENCE!

The instructions for use must be kept for the entire life of the universal child restraint system.
WARNING!

1. This car seat provides optimal safety in all installation positions for which it was designed.

2. This is an i-Size Enhanced Child Restraint System (40-105cm). It is approved pursuant to European Regulation 129 ( ECE R129 ), for use in i-Size compatible car seats as indicated by manufacturers in the car owner’s manual. If you have questions, please consult either the Enhanced Child Restraint System manufacturer or the distributor.

3.  This is an i-Size booster Enhanced Child Restraint System (100-135cm). It is approved according to ECE R129, for use in i-Size compatible seats, as indicated by the manufacturer in the car owner’s manual. If you have questions, please consult either the Enhanced Child Restraint System manufacturer or the distributer.

4. This is a booster seat for specific cars (135-150cm) and is an Enhanced Child Restraint System. It is approved according to European Regulation R129, for use in specific
   cars detailed in the applicable vehicle list. If you have questions, please consult either the Enhanced Child Restraint System manufacturer or the retailer.

5. This is an ‘i-Size Universal’ child restraint system, approved pursuant to European ECE R129, for its general use in cars, although it is not suitable for all cars.

6. It should be installed in cars for which the manufacturer states in its car owner’s manual that the vehicle is suitable for an ‘i-Size Universal’ child restraint system for this age range.

7. The product has been approved pursuant to European regulation ECE R129 and can be used for heights between 40 and 150 cm and maximum weight 36 kg.

8. Make sure that the buckle is correctly fastened before starting to drive.

9. Any straps holding the restraint to the vehicle should be tight, that any support-leg should be in contact with the vehicle floor, that any straps or impact shields restraining the child should be adjusted to the child’s body, and that straps should not be twisted.

10. Ensure that any strap or belt that holds the child is not folded or twisted and remains tightened.

11. Ensure that the abdominal belt or strap rests as low as possible over the child’s hips, on both sides.

12. In the event of an accident, even if there are no apparent damages, the seat may be unsafe. The seat should be replaced after being subjected to the sudden and strong stresses associated with an accident.

13. Instructions illustrations are for informational purposes only. The child restraint system may contain small differences compared to the photographs or images in the instructions manual. These variations do not affect its approval by Regulation ECE R129.

14. Under no circumstances should the car seat be installed in the car’s passenger seat opposite the direction of travel if there is an active airbag.

15. Please read the instructions carefully, as incorrect installation could result in serious injury. In this case, the manufacturer shall not be held liable.

16. Ensure that all the locking devices are engaged before use.

17.  It is dangerous to undertake any changes or additions to the safety seat with approval from the competent authority. It is dangerous to not strictly follow the installation instruc-tions provided by the child car set manufacturer.

18. Please never use the safety seat without its cover or without the harness protectors.

19. Make sure to protect the child safety seat from direct sunlight as it could heat up and hurt the child.

20. The car seat should remain permanently installed in the vehicle, even when the child is not in it. Never leave the child unattended when sitting in the car seat, even when the seat is outside the vehicle.

21. Make sure that any luggage or objects that could cause injuries in the event of an accident are fastened securely.

22. The cover of the child restraint system should not be replaced with another, unless recommended by the manufacturer, because it is an integral part of the system for securing children!

23. It should be installed in cars for which the manufacturer states in its car owner’s manual that the vehicle is suitable for an ‘i-Size Universal’ child restraint system for this age range.

24. Security is only guaranteed if the child restraint is fitted in accordance with these instructions.

25. For the i-Size enhanced child restraint system, the user must read the instructions manual of the vehicle’s manufacturer.

26. Don’t use in forward facing before the child reaches the age of 15 months.

27. Do no use rearward facing child seat in seating positions where an active frontal airbag installed. Death or serious injury can occur.

28. It is important to ensure that any lap strap is worn low down, so that the pelvis is firmly engaged.

29. The instruction must be retained on the child restraint for its life period.

30. The hard components or plastic parts of safety device for children should be deployed and installed in way that during everyday use of the vehicle not be jammed by the movable seats or doors. Prevent harness/vehicle belt from getting trapped between car doors or rubbing against sharp parts of the seat or body.

31. All belts that fix the restraint system to the vehicle must be tightened , all belts retaining the child must be adjusted according to the child’s body. Twisting of the belts shall not be allowed.

32. Don’t use another support point of contact except the ones described in the instructions and marked on the child restraint system.

33. If the child restraint system offers alternative support point of contact and you consider that using that alternative route is not satisfactory, please contact the manufacturer of the child restraint system.

34. Install the car seat in the seating positions indicated in this instruction.

35. Do not use the car seat in the house. It is not designed for home use and should only be used in the vehicle.

36. Before you set any mobile or adjustable part of the child seat, you need to remove your child from the child seat.

37. Check regularly the belts for wearing by paying special attention to the fixing points, the safety guards and the adjusting devices.

38. Do not leave the buckle partially closed, it must be locked when all parts are engaged. You must be able to remove the child from the seat immediately in case of emergency. You have to teach the child not to play with the buckle.

39. Keep the child’s chair at a safe place away from children when not in use. Avoid placing heavy objects on the chair. Prevent contact of your vehicle chair with corrosive substances, for example acid from the battery.

Do NOT install in front seats except in these specific cases:

1. When the car does not have back seats.
2. When all back seats are occupied by children less than or equal to 135 cm tall.
3. When it is not possible to install all child restraints in the back seats.
   In seats with: ISOFIX anchorages and Top Tether anchor points and 3-point belt (car’s seat belt).

ATTENTION
The child seat must only be used in this seat IF it has ISOFIX anchorages, top tether points a lap and 3 points belt: diagonal (A) and abdominal (B).

PARTS

1. Headrest; 2. 3-point safety belt guide; 3. Shoulder strap guide; 4. Shoulder straps; 5. Seat cushion 6. Shoulder pad; 7. Buckle; 8. Shoulder strap adjusting belt; 9. Base; 10. Adjusting button for rotation; 11. Adjusting lever for rotation; 12. Reclining adjuster; 13. Crotch pad; 14. Backrest; 15. Side protector (3 options); 16. Headrest adjusting lever; 17. Top tether; 18. Connective band of strap sleeve; 19. Shoulder straps; 20. Harness strap hook; 21. Shoulder straps adjusting belt; 22. ISOFIX release button; 23. ISOFIX locking display window;

 OPTIONS FOR SIDE PROTECTORS

1. Base with rotate button
2. Base with rotate handle
3. Without side preotectors.

USAGE METHOD

1. Adjust the headrest: Depending on the height of the child , the head is adjusted in 12 positions. As shown, adjust the headrest to the appropriate height by adjusting the red headrest lever up and down.
   Important: after loosening the headrest by adjusting the red lever, check that the headrest is locked in a safe and suitable position by pulling up or down the headrest.

2.  Check the height of the straps: Check that the height of the shoulder strap is suitable for your child: straps should pass through the strap holes that are equal to the child’ s shoulder or slightly higher than the child’ s shoulder position.
   The height of the shoulder strap of this product can be adjusted up and down together with the headrest. When using, adjust the height of the headrest to adjust the shoulder strap to the suitable height.

3. Buckle using – Step 1: Connect two buckle tongues.

4.  Buckle using – Step 2: Insert them together into the buckle. If you hear “click”, it means that the buckle is locked. Pull up the buckle tongues, and check that the buckle is locked tightly.

5. uckle using – Step 3: To unlock the shoulder strap, press the red button and separate the two buckle tongues.

6. Adjust the length of the straps – Tighten the straps:
   Pull the straps outward until the straps are completely tightened. Tighten the straps as much as possible without causing discomfort to the child. The lap belt is as low as possible and should be located near the crotch rather than the abdomen.

WARNING! Loosen straps are dangerous. So every time the child is placed in the child safety seat, check that the seat belt silver adjuster can be used normally, and then pull the straps, tighten the straps, and do not twist the straps.

Adjust the length of the straps – Loosen the straps:
The shoulder strap can be loosened by pressing the silver adjuster (hidden under the cover of the seat).
Action: press the silver adjuster down while the other hand holds the two straps to the right front of the child to loosen the straps.

Adjust ISOFIX
Press the red ISOFIX release button and push the ISOFIX out to the outermost so that the ISOFIX can be installed.
If you want to retract the ISOFIX, you can pull the ISOFIX back by pressing the red ISOFIX release button.

installation of child safety seat

1. Step 1: first pull the ISOFIX to the outermost end, then insert the ISOFIX to the anchor on your car. When you hear “click”, it indictates that the ISOFIX is totally locked. Note: At this time, the ISOFIX lock display window appears green.
2. Step 2: Push the seat against the back of the car until the two are perfectly tightly aligned. If you want to release the ISOFIX chuck, you can unlock the ISOFIX chuck by pressing the red release button of it.
3. Step 3: Use a 3-point safety belt to install the child safety seat.

Adjust the angle of the child safety seat
The seat angle can be adjusted by pressing the red angle adjusting lever. It is convenient to adjust the suitable angle and increase comfort when using.

Rotating adjustment of the child car seat

Note: There are two optional bases for this product. One is the base with an adjusting lever, the other one is with a button.

1. Option 1: Base with an adjusting lever: As show in the figure, pull the red adjusting lever to rotate the child car seat in 360°.
2. Option 2: Base with a button. As shown in the figure, press the red button to rotate the child car seat in 360°.

 INSTALLATION AND USE OF THE CHILD SAFETY SEAT

Installation of the child safety seat (height 40-105cm)
This product is suitable for children in height 40-105cm, Rearward facing installation.

1. Step 1: First adjust the seat to the most inclined gear, and then rotate the seat body 180 degrees on the car seat.
2. Step 2: Secure the seat to the car seat with ISOFIX, make sure the ISOFIX is locked, the display window appears green, and then slowly push the seat onto the back of the car seat until it fits completely.
3. Step 3: Loosen the buckle and shoulder strap, put the child in the child’s seat, and then buckle and pull the shoulder strap. Check the shoulder strap and head height. Note: all seat belts should not be twisted.
4. Step 4: Use the adjusting buckle on the top tether to adjust the top tether to the appropriate length. The top tether of the seat is passed through the side of the head of the seat. The top tether is attached to the corresponding hook on the car (the attachment point suggested in the manufacturer’s manual), finally tighten the top tether when the top tether is secured, its regulator is shown as green.

Installation of the child safety seat (height 76-105cm)
This product is suitable for children in height 76-105cm, Forward installation

1. Step 1: Use ISOFIX to secure the seat to the car seat, make sure the ISOFIX is locked, the display window appears green, and then push the seat slowly to the back of the car seat until fully fitted.
2. Step 2: Pull out the top tether as shown in the figure.Use the adjustment buckle on the top tether to adjust the top tether to the appropriate length. As shown in the figure, hang the top tether on the corresponding hook of the car (the node recommended in the
3. carmaker’s manual). Finally, the top tether is tightened, and when the top tether is fixed, the regulator shows green.
4. Step 3: First loosen the pull-out buckle and shoulder strap, put the child into the child seat, and then buckle the pull-out buckle to tighten the shoulder strap. Check shoulder strap and head height. Note: All seat belts must not be distorted. Its regulator shows green.

Installation of the child safety seat (Height: 100-150cm)

This product is suitable for children height: 100-150cm, Forward installation
Remove the harness system and buckle, hide the whole buckle in the hole on the base which is under the cover.

1. Step 1: Adjust the child safety seat to the most upright position.
2. Step 2: Insert the ISOFIX to the isofix connector on you car. Make sure that the ISOFIX display window is green. Then push the child safety seat to the backrest of your car seat until it is fully fitted.
3. Step 3: Place your child into the child safety seat and fix your child with 3-point safety belt. Note: All seat belts shall not be twisted.

Removal of seat belts and buckles

1. Step 1: Loosen the belt system.
2. Step 2: Pull the belt system out of their metal brackets on the back side of the child car seat, guide these through the child car seat to the front side.
3. Step 3: Remove the seat cushion and remove shoulder pads.
4. Step 4: Separate the buckle tongues from the buckle. Turn over the seat cover, then through the shoulder belts of each side from the cover opening. Remove the crotch pad, through the buckle from the cover opening to the back.Take the tongues from the belts then insert to the buckle.
5. Step 5: Fold the belt on the sides. Hide the buckle with its tongues in the hole on the base.

REMOVAL AND INSTALLATION OF THE FABRIC COVER

• Remove shoulder straps and shoulder covers;
• Release the buckle first, then remove the crotch pad and seat cushion.
• Unbutton the headrest and base, respectively, and remove the sleeve. Note: if you need to install the cover again, please operate in reverse order of removal.

MAINTENANCE AND CLEANING

ROUTINE MAINTENANCE

• During daily use, child safety seat’s wear and tear should be checked regularly. In the event of an accident, the seat needs to be replaced.
• When not using child safety seats, place them in a dry, ventilated place to avoid damp and mildew.
• If dust is found on the surface of the child safety seat, dry the seat belt and plastic parts with a damp sponge and then dry by ventilation.
• If you drop food or drink onto your seat belt, remove it and rinse it with warm water, then dry by ventilation.

Produced for Kikka Group Ltd., Vasil Levski 121, Plovdiv, Bulgaria. Made in China. Complies with EN R129.

Kika Group Ltd. Vasil Levski 121
4000 Plovdiv, Bulgaria office@kikkaboo.com +359 32 51 51 51

KikkaBoo España S.L.
Pol. ind., Los Álamos s/n, Fase II, Nave 17 18230 Atarfe (Granada), España oficina@kikkaboo.com
+34 919 148 299
www.kikkaboo.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>