kikka boo i-TRAVEL Car Seat Instruction Manual

kikka boo i-TRAVEL Car Seat Instruction Manual

IMPORTANT! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

WARNING IMPORTANT- READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

Important safety instructions!
WARNING!
Under no circumstances should the safety seat be installed in the front seat of the car opposite the direction of travel if the car is equipped with an active airbag.
WARNING! This car seat is designed to offer the optimal safety in all installation modes described in this manual. WARNING! This is a i-Size booster seat Enhanced Child Restraint System(100-135cm). It is approved according to Regulation ECE R129, for use primarily in” i-Size seating positions”as indicated by vehicle manufacturers in the vehide user’s manual. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer. WARNING! This is a specific vehide booster seat Enhanced Child Restraint System (135-150cm). It is approved according to UN Regulation No. 129/03, for use in specific vehicle indicated in the applicable vehicle list. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
WARNING! This is an “i-Size Universal”child restraint system, it is approved to regulation No. 129 series of amendments, for general use in vehicles and it will fit most, but not at all, car seats. If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
WARNING! A correct fit is likely if the vehicle manufacturer has declared in the vehicle handbook that the vehide is capable of accepting an” i-Size Universal”child restraint system for this age group.
WARNING! Ensure that the part of any abdominal belt or strap should rest as low as possible over the child’s hips, on both sides.
WARNING! Please read the instructions carefully, as incorrect installation could result in serious injury. If any injuries should occur as a result of incorrect installation, the manufacturer will accept no liability.
WARNING! The product has been approved according to the strictest European safety standards (ECE R129) and is suitable for the height range between 100 and 150 cm.
WARNING! Please never use the safety seat without its cover or without the harness protectors.
WARNING! Fastening a child dressed in outerwear could reduce the efficiency of the restraint system.
WARNING! Make sure to protect the child safety seat from direct sunlight as it could heat up and hurt the child. WARNING! Child seats or hamess accessories that are damaged or have been used incorrectly must be replaced. WARNING! Do not leave heavy objects inside the car, as these may injure the child in the event of an accident. WARNING! Make sure that the buckle is correctly fastened so that the child can be quickly freed in case of emergency. WARNING! The safety seat’s rigid and plastic elements should be positioned and installed so that they cannot be trapped by a moving seat or a door during everyday use of the vehicle.
WARNING! Do not disassemble, modify, or add any piece to the child seat or harness, as this would seriously affect its basic functioning and the safety that the child seat provides.

WARNING! The safety seat must remain installed in the vehicle with the safety belt, even if the child is not seated in the child seat. The child must never be left unattended while seated in the safety seat, not even outside the vehicle.
WARNING! Keep the safety seat away from corrosive products.
WARNING! Do not use anchor points that are not listed in the instruction manual and indicated on the seat.
WARNING! The seat should be replaced after undergoing the violent stresses associated with an accident.
WARNING! The manufacturer guarantees the quality of its products, but not the quality of second-hand products or products belonging to other companies.
WARNING! Instruction illustrations are for informational purposes only. The child restraint system may contain small differences compared to the photographs or images in the instruction manual. These variations do not affect its certification under ECE Regulation R129.
WARNING! Ensure that any strap or belt that holds the child is not bent or twisted and keeps tightened. Act under the same criteria with the vehicle belts that serve as a restraint for the chair.
WARNING! Take advice from your vehicle manual to check compatibility with “i-Size”child restraint systems.
WARNING! Fitting the child with warm clothing into this safety seat may reduce the effectiveness of the restraint system.

Only suitable if the approved vehicles are fitted with 3 point safety belts, approved to UN/ECE Regulation Nº16 or other equivalent standards. 1. Car belt Diagonal belt. 2. Car belt Lap belt

The vehide rear seat is the safest position for kids under 12 years. This child seat must be installed with forward facing Rearward facing and side ward facing is strictly prohibited. Do not install the child safety seat at the front seat with airbag.

   You can install this position
 Unable to install the position
 Do not install the child safety seat at the front seat with air bag.
 Only with the three point safety belt you can put the seat in this location.

IMPORTANT! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

SAFETY NOTICE
Check whether the safety seat is installed correctly. Proper installation is crucial to ensure the safety of children. The fixing of the safety seat must follow the instructions on the belting stickers located on both sides of the seat or the instructions in the manual (See Fig.2.1) Move the front seat as far forward as possible to ensure that the baby’s legs have a comfortable space for movement (See Fig.2.2)



CHILD SEAT USED AS FSIZE BOOSTER SEAT
USE CAR BELT+ISOFIX INSTALLATION APPLICABLE TO VEHICLES EQUIPPED WITH ISOFIX SYSTEM THAT MEETS THE REQUIREMENTS OF ECE R14 1). Find the ISOFIX foxed anchor point on the car, and dip the two guide sleeves to the two ISOFIX fixed anchor points of the car to facilitate subsequent installation. 2). Press and hold the ISOFIX unlock button while sliding outwards to adjust the SOAX connectors on both sides of the safety seat to the longest state 3).Connect the ISOFIX connector of the safety seat to the ISOFIX anchor point of the car until you hear a “click” sound.Tip: For the location of the ISOAX fixed anchor point, please check your car’s user manual or contact your car manufacturer or local dealer. 3.2.
USE THREE-POINT SEAT BELTS TO SECURE CHILDREN

1. Adjust the length of the safety belt guide hook. The shoulder belt of the car safety belt must pass through the guide hook and the top of the armrest, and the waist belt must pass through the guide groove.
2. Let the child sit on the safety seat and adjust the length of the safety belt guide hook according to the baby’s height.
3. Pull out the car three-point safety belt, the shoulder belt of the safety belt passes through the guide hook and the top of the armrest, the abdominal belt of the safety belt passes through the guide grooves on both sides of the safety seat, and is fixed to the car buckle, and you hear “Click” sound to ensure that the buckle is firmly locked.
4. Recycle and tighten the car seat belt, and adjust the tightness of the car seat belt according to the size of the child, and it must not be tumed over or twisted. Please make sure that the position of the seat belt waistband is as low as possible, so that the child’s pelvis can be better fixed.

USE THREE-POINT SEAT BELT INSTALLATION APPLICABLE TO VEHICLES EQUIPPED WITH ISOFIX SYSTEM THAT MEETS THE REQUIREMENTS OF ECE R14

1. Ensure that the ISOFIX connector of the safety seat is retracted into the base, and place the safety seat on both sides of the rear row.
2. Let the child sit on the safety seat and adjust the length of the safety belt guide hook according to the baby’s height.
3. Pull out the car three-point safety belt, the shoulder belt of the safety belt passes through the guide hook and the top of the armrest, the abdominal belt of the safety belt passes through the guide grooves on both sides of the safety seat, and is fixed to the car buckde, and you hear “Click” sound to ensure that the buckle is firmly locked.4). Recyde and tighten the car seat belt, and adjust the tightness of the car seat belt according to the size of the child, and it must not be turned over or twisted. Please make sure that the position of the seat belt waistband is as low as possible, so that the child’s pelvis can be better fixed.

CHILD SEAT USED AS UNIVERSAL BOOSTER SEAT

INSTALLATION METHOD
Applicable to vehicles equipped with ISOFIX system that meets the requirements of ECE R14 SOFIX+3 point safety belt.

1. Find the ISOFIX fixed anchorage point on the car, and dip the two guide sleeves to the two ISOFIX fixed anchorage points of the car to facilitate subsequent installation.
2. Press and hold the ISOFIX unlock button while sliding outwards to adjust the ISOFIX connectors on both sides of the anchorage seat to the longest state.
3. Connect the ISOFIX connector of the anchorage seat to the ISOFIX anchorage point of the car until you hear a “dick” sound. Tip: For the location of the ISOFIX fixed anchorage point, please check your car’s user manual or contact your car manufacturer or local dealer.

ISOFIX+3 POINT SAFETY BELT

1. Adjust the length of the safety belt guide hook. The shoulder belt of the car safety belt must pass through the guide hook and the top of the armrest, and the waist belt must pass through the guide groove.
2. Let the child sit on the safety seat and adjust the length of the safety belt guide hook according to the baby’s height.
3. Pull out the car three-point safety belt, the shoulder belt of the safety belt passes through the guide hook and the top of the armrest, the abdominal belt of the safety belt passes through the guide grooves on both sides of the safety seat, and is fixed to the car buckle, and you hear “Cick” sound to ensure that the buckle is firmly locked
4. Recycle and tighten the car seat belt, and adjust the tightness of the car seat belt according to the size of the child, and it must not be turned over or twisted. Please make sure that the position of the seat belt waistband is as low as possible, so that the child’s pelvis can be better fixed.

APPLICABLE TO VEHICLES EQUIPPED WITH ISOFIX SYSTEM THAT MEETS THE REQUIREMENTS OF ECE R143 POINT SAFETY BELT

1. Ensure that the ISOFIX connector of the safety seat is retracted into the base, and place the safety seat on both sides of the rear row.
2. Let the child sit on the safety seat and adjust the length of the safety belt guide hook according to the baby’s height.
3. Pull out the car three-point safety belt, the shoulder belt of the safety belt passes through the guide hook and the top of the armrest, the abdominal belt of the safety belt passes through the guide grooves on both sides of the safety seat, and is fixed to the car buckle, and you hear “Click” sound to ensure that the buckle is firmly locked.
4. Recycle and tighten the car seat belt, and adjust the tightness of the car seat belt according to the size of the child, and it must not be turned over or twisted. Please make sure that the position of the seat belt waistband is as low as possible, so that the child’s pelvis can be better fixed.

DETACHING FROM CAR SEAT (Fig. 5.1. 1).

1. Press and hold the ISOFIX unlock switch on both sides at the same time. At this time, the ISOFIX lock indicator turns red, which means it is unlocked.
2. Pull the safety seat outwards to remove the safety seat. 5.2. HEADREST HEIGHT ADJUSTMENT Pull up the handle of the seat headrest to adjust it up and down, release the handle to lock the head sition. Note: Please ensure that the seat headrest is locked.

5.3. DETACHING FROM CAR SEAT

1. Press and hold the ISOFIX unlock switch on both sides at the same time. At this time, the ISOFIX lock indicator turns red, which means it is unlocked
2. Pull the safety seat outwards to remove the safety seat.

INSTALLATION AND DISASSEMBLY OF THE SEAT BACK AND BASE
After laying down the seat, press the base with one hand and pull up the back of the chair with the other to separate the back of the chair from the base. Press the back of the chair downward to insert the back of the chair into the connecting shaft to combine the back of the chair with the base.

CARE AND MAINTENANCE

1. In daily use, check periodically the child seat. The child seat should be replaced after an accident.
2. Please keep this child seat in dry and ventilated place to avoid damp moldy.
3. If the child seat becomes dusty, dean the seat belt and the plastic pieces by swiping them with a damp sponge and let it dry naturally.
4. If food or drink drop accidently on the buckle,disassemble the seat belt from the child seat and rinse it gently by warm water. Leave it dry naturally.
5. For deaning the entire child seat fabric cover,please refer to the Washing instructions Never use any solvant, chemical detergent or lubricant on any part of your child seat Remove and assemble the fabric cover 1. Firstly,remove the crotch pad and buckle of the child seat, and then remove the shoulder straps and comfortable cushion.
   Remove the fabric cover of the child seat. To install the fabric cover, please operate follow the above instructions in reverse order. Hand wash, water temperature below 30°C. Do not bleach. Drydean, any solvent except trichloroethylene. Do not tumble dry. Do not iron

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>