Polybird P-31 4 Glider Chair Instruction Manual

Table of Contents

Polybird-P-31-4-Glider-Chair-PRODUCT-IMAGE

Specifications:

Product Name : Glider P-31
- Tools Required : 7/16 Wrench, 1/2 Wrench, Hex Key, Screwdriver (not provided)
Hardware Included : AA x4 1/4 x 2 1/4 Wafer Bolt, BB x2 1/4 x 1
- 3/4 Wafer Bolt, CC x4 2 1/2 Screw, DD x8 1 1/2 Screw, FF x4 5/16 x
- 2 1/2 Wafer Bolt, GG x6 1/4 Flange Nut, HH x4 5/16 Lock Nut

Step 1: Seat Assembly
- Attach seat (B) to arms C and D using four 1/4 x 2 1/4 wafer bolts (AA) and two 1/4 x 1 3/4 wafer bolts (BB). Add a 1/4 flange nut (GG) to each bolt.
Step 2: Seat Back Assembly
Attach seat back (A) to the assembly from step 1 using four 2 1/2 screws (CC) and two 1 1/2 screws (DD). Insert six 1 screws (EE) under arm rests.
Step 3: Glider Base Assembly
Assemble the glider base by attaching base pieces G & H to F & E using three 1 1/2 screws (DD) in each corner.
Step 4: Chair Assembly
Lift the chair assembly from step 2 over the base assembly from step 3. Attach the chair to the base by inserting a 5/16 x 2 1/2w afer bolt (FF) through the leg and metal support on the base, finishing with a lock nut (HH).
- Note: Wait until the whole piece is assembled before tightening the bolts completely.
- We hope you enjoy your new piece of furniture for years to come!

Frequently Asked Questions (FAQ)

Q: What should I do if I am missing a hardware piece?
A: If you are missing any hardware pieces, please contact our customer support for assistance in acquiring the necessary parts.
Q: Can I disassemble the glider P-31 once it is fully assembled?
A: While it is possible to disassemble the glider P-31, it is recommended to seek professional assistance to ensure proper disassembly and reassembly without causing damage to the product.

$Polybird-P-31-4-Glider-Chair- $6$$

Note before starting: wait until the whole piece is assembled to tighten the bolts completely.

$Polybird-P-31-4-Glider-Chair- $2$$

Attach seat (B) to arms C and D using four 1/4” x 2 1/4” wafer bolts (AA), one for each front leg and one for each top hole in the back legs, working from the outside in. Then use two 1/4” x 1 3/4” wafer bolts (BB), one for each bottom hole in the back legs. Add a 1/4” flange nut (GG) to each bolt, as shown. $Polybird-P-31-4-Glider-Chair- $3$$
Attach seat back (A) to assembly from step 1 by inserting four 2 1/2” screws (CC) through the back brace at the seat and two 1 1/2” screws (DD) in the middle, as shown. Then insert six 1” screws (EE) under arm rests. $Polybird-P-31-4-Glider-Chair- $4$$
Assemble glider base. Attach base pieces G & H to F & E using three 1 1/2” screws (DD) in each corner, as shown. $Polybird-P-31-4-Glider-Chair- $5$$
Lift chair assembly from step 2 over base assembly from step 3. Attach chair to base working from the outside in: Insert a 5/16” x 2 1/2” wafer bolt (FF) through leg and then through metal support on base, finish with a lock nut (HH). Repeat for each of the 4 corners of the chair.
We hope you enjoy your new piece of furniture for years to come!