RunCam Hybrid 2 User Manual
- June 7, 2024
- RunCam
Table of Contents
RunCam Hybrid 2
Instruction Diagram
Lens Module Connection Diagram
Micro SD Card
Capacity up to 128GB; U3 recommended (2.7K50/1080P120 requires U3 or above; other solutions require U1 or above)
Please push the shield a little bit up with one hand as shown in above step 1 and then press the SD card(step 2) with another hand to let the card pop out.
Basic Camera Operation
Transmitter Connection Diagram
Warning: Current Input ≥1A (Don’t power by VTx)
FPV Flight Controller Setup
- Joystick Control
- FPV OSD Menu
- FPV camera supports Joystick Control and UART Control. The top left corner of the screen will shortly display the current control mode. The default is Joystick control
mode. You can switch the mode via the below way:
- Short the two camera control pins (TX and RX on board as shown in below picture)
- Then power on, and the camera will auto-switch between the two modes. The mode can be saved after the power is off.
- After switching to the desired mode, please unplug the short-circuit cable.
UART Control works with Flight Controllers: BetaFlight 3.3 or above / ButterFlight 3.4 or above / CleanFlight 2.2 or above
Joystick Control
FPV OSD Menu
- JOYSTICK CTRL: The camera is under Joystick Control and the icon remains for 5 seconds.
- CARD ERROR: Card error or no SD card
- CARD FULL: SD card is full
- 4K 30FPS: Current video resolution, remains for 10 seconds
- Quick Setting (Long press the upper button to enter the menu)
- Press the middle button to switch ON / OFF
- CLR: Clear RUN CAM logo or pilot’s name
- POS: Move to POS to adjust the position
- SHARP VIEW: Turn on, it will increase the image details, but also noise
- WIDESCREEN: Switch image ratio between 16:9 and 4:3.
- SYSTEM: Press the middle button to switch NTSC/PAL. It will work only after you exit the menu and reboot.
- EXIT: Exit and saved.
UART Control
- 1. Flight controller wiring (Take UART3 for example)
- Betaflight 3.3 or above setting
Just need to choose “Camera (RunCam Protocol)” on UART 3 as shown in the below
screenshot.
- UART Control (Operate with your remote controller. Yellow icon to indicate bar operation direction. Black dot means centering control )
- When connected, The buzzer on Flight Controller will beep 3 times; When disconnected, The buzzer on Flight Controller will beep 2 times only; If connected successfully, you can long press the up button to enter the OSD menu, and right button to switch preset scenes, left button to calibrate voltage and down button to reset OSD.
Camera Menu
- MODE (MWB/ATW)
- VIDEO STANDARD (PAL/NTSC)
- IMAGE RATIO (4:3 /16:9)
- EXPOSURE MODE (BLC/ GLOBE)
- MODE (COLOR / BW / EXT / AUTO)
- CONTRAST (MANUAL/AUTO)
- SHARPNESS (MANUAL/AUTO)
- COLOR GAIN (MANUAL/AUTO)
HD Flight Controller Set
Preparation
- Firmware: BetaFlight Firmware (≥3.2.0),CleanFlight Firmware(≥2.1.0) ,
- KISS Firmware (≥1.3-RC30) or INAV Firmware (≥1.7.3).
- Any available UART interface on the Flight Controller
- Connect the RunCam Hybrid with the UART interface of the Flight Controller
Make the Flight Controller recognize the RunCam Hybrid
For example, we connect the RunCam Hybrid to the UART 5 interface on the
Flight Controller: connect the Flight Controller to the computer, then open
the configurator software of the Flight Controller. (Open up the configurator
that matches the firmware you are running, Betaflight Configurator for
Betaflight, Cleanflight Configurator for Cleanflight). In the Peripherals
column of the line UART 5 (on the Ports tab), select Camera (RunCam Protocol)
and click Save And Reboot.
- Instructions on the functions of the camera and assigning transmitter channels to them
- In the Flight Controller Configurator, navigate to the Modes tab. There are new CAMERA WI-FI, CAMERA POWER, and CAMERA CHANGE modes
- Assign any available channel to the function you need, for example:
- CAMERA POWER: start/stop the video. When in the OSD of the camera, this is used to move to the next menu item.
- CAMERA CHANGE MODE: Switch between the recording mode and the QR code setting mode.
- Assign the AUX2 to the CAMERA POWER, range 1900-2100
- Assign the AUX3 to the CAMERA CHANGE MODE, range 1900-2100
Assign the channel to the switch of the controller
Please choose your Model on the controller, then access the MIXER interface
and assign the channel to the switch of the controller. Take opentx 2.2.0 for
example, assign the channels CH5, CH6 and CH7 to SA, SB and SD
respectively
Test
Power the Flight Controller and the RunCam Hybrid
- Set the SA to the bottom, and the camera starts/stops the video
- Set the SD to the bottom, and
- the camera switches among the two modes: video and OSD setting mode
Technical Support
Please visit:https://support.runcam.com
Parameter
Documents / Resources
|
RunCam RunCam Hybrid
2
[pdf] User Manual
RunCam Hybrid 2, RunCam
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>