Thermalright AXP-200R CPU Cooler Installation Manual
- June 15, 2024
- THERMALRIGHT
Table of Contents
Thermalright AXP-200R CPU Cooler
LGA 1151 Spacer Installation
- To use the spacer, install the CPU into the socket as instructed by Intel
- Next, set the Thermalright LGAllSl Spacer on top of the CPU so you can read ‘Thermalright’ on the hinge side of socket.
- Close the load plate and secure it with the bolt
- Job done
Assembly Package
Intel 775/1150/1151/1155/1156/1366
Exploded View
Important! Before proceeding with installation, please check for the most up- to-date instructions at www.thermalright.com
- M3 L17 Screw
- TY-14013R Fan
- Heatsink Body
- Anchoring Mount
- M3 L6 Screw
- Mounting Plate
- Screw Nut
- Intel Washer (small)
- Mylar
- Metal Back Plate
- M3 L10 Screw
Component
- Heatsink Body ×1
- Enhanced Fan Mount ×1
- Metal Back Plate ×1
- Mounting Plate ×1
- Anchoring Mount ×1
- Screw Nut ×4
- LGA2011 Type B Screw Pillars x4
- M3 L10 Screw ×5
- M3 L6 Screw ×7
- Intel Washer (small) ×8
- AMD Washer (big) ×4
- Back Plate Cap ×1
- Chill Factor III ×1
- TY-14013R Fan×1
- M3 L4 Screw ×5
- M3 L17 Screw ×5
- M3 L28 Screw ×5
- Mylar ×1
Installation Instructions
Step 1:
-
Step 1: Backplate Installation
Choose the platform (775/1150/1151/1155/1156/1366) you are in use. Make four M3L10 Screw Pillars go through the Metal Back Plate and the Mylar film from bottom to top. And then place the Metal Back Plate on the table. Put the four Washers (for Intel) around the Screw Pillars. -
Step 2: Back Plate Cap
Note: When installing on a 775 platform, please first insert the Back Plate Cap into the opening on the Back Plate. Make sure you have the Cap facing downwards. (Only for 775).
-
Step 3: Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four holes around the processor socket.Cap the four Screw Cylinders with the four Screw Nuts. Make sure the side with a washer is facing the Back Plate. -
Step 4: Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount on to the Screw Nuts.
-
Step 5: Applying Thermal Paste
Apply the Chill Factor III to the base of the Heatsink and the surface of the CPU evenly.
-
Step 6: Mounting Plate Installation.
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the two M3L6 screws to secure the Mounting Plate. (Screwdriver goes through holes on fins)
-
Step 7A : Fan Installation
Place the included TY-14013R fan onto the heatsink body. And then secure it by screwing on the four M3L17 screws, through the fan mounting holes. -
Step 7B: Fan Installation
Or, if the fan is flipped over to draw air towards the top as shown in Step 7B, then place four washers (for Intel boards) underneath the fan for additional height before securing the fan onto the heatsink body.
-
Step 8: Installation Completed
Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete.
Intel 2011/2011-3/2066
Exploded View
Important! Before proceeding with installation, please check for the most up-to-date instructions at www.thermalright.com
- M3 L17 Screw
- TY-14013R Fan
- Heatsink Body
- Anchoring Mount
- M3 L6 Screw
- Mounting Plate
- LGA 2011 Type B Screw Pillars
Component
- Heatsink Body ×1
- Enhanced Fan Mount ×1
- Metal Back Plate ×1
- Mounting Plate ×1
- Anchoring Mount ×1
- Screw Nut ×4
- LGA2011 Type B Screw Pillars x4
- M3 L10 Screw ×5
- M3 L6 Screw ×7
- Intel Washer (small) ×8
- AMD Washer (big) ×4
- Back Plate Cap ×1
- Chill Factor III ×1
- TY-14013R Fan×1
- M3 L4 Screw ×5
- M3 L17 Screw ×5
- M3 L28 Screw ×5
- Mylar ×1
Installation Instructions
-
Step 1: Screw Pillar Installation
Screw the four LGA2011 Type B Screw Pillars into the Heatsink studs on the ILM Assembly Frame around the processor socket. -
Step 2 : Anchoring Mount Installation
Place the Anchoring Mount onto the four LGA2011 Type B Screw Pillars, secure it by tightening it with 4 M3L6 Screws. -
Step 3: Applying Thermal Paste
Apply the Chill Factor III to the base of the Heatsink and the surface of the CPU evenly.
- Step 4: Mounting Plate Installation.
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the two M3L6 screws to secure the Mounting Plate. (Screwdrive goes through holes on fins)
-
Step 5A : Fan Installation
Place the included TY-14013R fan onto the heatsink body. And then secure it by screwing on the four M3L17 screws, through the fan mounting holes. -
Step 5B: Fan Installation
Or, if the fan is flipped over to draw air towards the top as shown in Step 5B, then place four washers (for Intel boards) underneath the fan for additional height before securing the fan onto the heatsink body. -
Step 6: Installation Completed
Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete.
AM4/AM2/AM2+/AM3/AM3+/FM1/FM2/FM2+
Exploded View
Important! Before proceeding with installation, please check for the most up- to-date instructions at www.thermalright.com
- M3 L17 Screw
- TY-14013R Fan
- Heatsink Body
- Anchoring Mount
- M3 L6 Screw
- Mounting Plate
- Screw Nut
- Back Plate Cap
- AMD Washer (big)
- Mylar
- Metal Back Plate
- M3 L10 Screw
Component
- Heatsink Body ×1
- Enhanced Fan Mount ×1
- Metal Back Plate ×1
- Mounting Plate ×1
- Anchoring Mount ×1
- Screw Nut ×4
- LGA2011 Type B Screw Pillars x4
- M3 L10 Screw ×5
- M3 L6 Screw ×7
- Intel Washer (small) ×8
- AMD Washer (big) ×4
- Back Plate Cap ×1
- Chill Factor III ×1
- TY-14013R Fan×1
- M3 L4 Screw ×5
- M3 L17 Screw ×5
- M3 L28 Screw ×5
- Mylar ×1
Installation Instructions
-
Step 1: Backplate Installation
Choose the platform (AMD) you are in use. Make four M3L10 Screw Pillars go through the Metal Back Plate and the Mylar film from the bottom to the top. And then place the Metal Back Plate on the table. Put the four Washers (for AMD) around the Screw Pillars. -
Step 2: Back Plate Cap
Note: When installing on a 939 platform, please first insert the Back Plate Cap into the opening on the Backplate. Make sure you have the Cap facing downwards. (Only for 939). -
Step 3: Place the motherboard on top of the Back Plate.
See the four Screw Cylinders go through the four holes around the processor socket. Cap the four Screw Cylinders with the four Screw Nuts. Make sure the side with a washer is facing the Back Plate. -
Step 4: Anchoring Mount Installation
Place the Anchoring Mount on the Screw Nuts. Use the four M3L6 Screws to fix the Anchoring Mount onto the Screw Nuts. -
Step 5: Applying Thermal Paste
Apply the Chill Factor III to the base of the Heatsink and the surface of the CPU evenly. -
Step 6: Mounting Plate Installation.
Place the Heatsink Body on top of the CPU. Make the Mounting Plate go through the Heatsink Body. Then use the two M3L6 screws to secure the Mounting Plate. (Screwdriver goes through holes on fins)
-
Step 7A : Fan Installation
Place the included TY-14013R fan onto the heatsink body. And then secure it by screwing on the four M3L17 screws, through the fan mounting holes. -
Step 7B: Fan Installation
Or, if the fan is flipped over to draw air towards the top as shown in Step 7B, then place four washers (for Intel boards) underneath the fan for additional height before securing the fan onto the heatsink body. -
Step 8: Installation Completed
Plug in the fan connector to the CPU PWM Fan socket on the motherboard. Installation complete.
Technical Spec
Heatsink Specifications
- Dimension: Length 153mm x Width 140mm x Height 60mm
- Weight: 470g (Heatsink only)
- Heatpipe: 6mm heatpipe * 6 units
- Copper Base: C1100 Pure copper nickel plated
Fan Specification
- Dimension: L150mm x H140mm x W13mm
- Weight: 90g
- Fan speed: 700~1300RPM
- Fan noise: 21.7~30.6dBA (Test distance 1.0M)
- Airflow: 35.18~64.52 CFM
- Connector: 4 Pin (PWM Fan connector)
The Ultimate Cooling Solutions!
Contact Information
- Website: www.thermalright.com
- Telephone (TEL): +886-2-2915-5005
- Fax (FAX): +886-2-2915-5123
- Email: sales@thermalright.com
FREQUENTLY ASKED QUESTIONS
What CPU sockets is the Thermalright AXP-200R compatible with?
The Thermalright AXP-200R CPU Cooler is compatible with Intel sockets 775, 1150, 1151, 1155, 1156, 1366, 2011, 2011-3, 2066, as well as AMD sockets AM4, AM2, AM2+, AM3, AM3+, FM1, FM2, and FM2+.
What is included in the package when I purchase the AXP-200R CPU Cooler?
The package includes the Heatsink Body, Enhanced Fan Mount, Metal Back Plate, Mounting Plate, Anchoring Mount, Screw Nut, LGA2011 Type B Screw Pillars (for Intel sockets), various screws, washers (for Intel and AMD), Back Plate Cap, Chill Factor III thermal paste, TY-14013R Fan, and more.
What is the maximum TDP (Thermal Design Power) that the AXP-200R CPU Cooler can handle?
The AXP-200R CPU Cooler is designed to handle CPUs with a TDP of up to 180 watts, making it suitable for a wide range of processors.
Does the AXP-200R CPU Cooler come with pre-applied thermal paste, or do I need to apply it myself?
The AXP-200R CPU Cooler does not come with pre-applied thermal paste. You will need to apply thermal paste (Chill Factor III) to the base of the heatsink and the surface of the CPU during installation.
What is the maximum height clearance for RAM modules when using the AXP-200R CPU Cooler?
The AXP-200R CPU Cooler is designed with RAM clearance in mind. It typically provides enough clearance for standard-height RAM modules. However, it's advisable to check the height of your RAM modules and compare it with the cooler's specifications to ensure compatibility.
Is the AXP-200R CPU Cooler compatible with small form factor (SFF) cases?
Yes, the AXP-200R CPU Cooler is designed to be compact and is suitable for small form factor (SFF) cases. Its dimensions are L153mm x W140mm x H60mm, making it a good choice for systems with limited space.
Can I use the AXP-200R CPU Cooler with both Intel and AMD platforms?
Yes, the AXP-200R CPU Cooler is versatile and compatible with both Intel and AMD platforms. It includes mounting hardware and instructions for installation on various Intel and AMD sockets, as outlined in the provided instructions.
What is the recommended fan speed for optimal cooling performance with the AXP-200R CPU Cooler?
he AXP-200R CPU Cooler comes with a TY-14013R fan, and its fan speed is adjustable in the range of 700~1300 RPM. The recommended fan speed may vary depending on your specific system and cooling needs. You can adjust the fan speed through your motherboard's BIOS or software to find the optimal balance between cooling performance and noise level.
Can I use third-party thermal paste with the AXP-200R CPU Cooler, or is it recommended to use the included Chill Factor III paste?
While the AXP-200R CPU Cooler includes Chill Factor III thermal paste, you can use third-party thermal paste if you prefer. However, using the included paste is recommended for best results, as it is specifically designed for Thermalright coolers.
Is the AXP-200R CPU Cooler compatible with RGB or LED lighting?
The AXP-200R CPU Cooler does not come with built-in RGB or LED lighting. However, you can typically add RGB or LED lighting elements to your system separately, such as by using RGB fans or LED strips, if you wish to add lighting effects.
Can I use the AXP-200R CPU Cooler for overclocking my CPU?
The AXP-200R CPU Cooler is designed to provide efficient cooling for a wide range of CPUs, including some higher-end models. While it can handle moderately overclocked CPUs, its primary focus is on providing reliable cooling for stock and mildly overclocked configurations. If you plan on heavy overclocking, you may want to consider a larger and more robust cooler.
Does the AXP-200R CPU Cooler come with a warranty for the included fan?
The AXP-200R CPU Cooler includes a TY-14013R fan. The warranty for the fan may vary, and it's typically covered by the fan manufacturer's warranty. Be sure to check the fan's warranty terms and conditions, which may differ from the warranty for the cooler itself.
REFERENCE:Thermalright AXP-200R CPU Cooler Installation Manual- device.report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>