Origin21 0328V4822BLU 48 Kellen Vanity with Top

Product Specifications

• Brand: ORIGIN21
• Model: TJ-0328V4822BLU / TJ-0328V4822BR
• Item Numbers: 5501915 / 5530622
• Product Name: 48 KELLEN VANITY WITH TOP

Product Usage Instructions

Preparation:
Before beginning assembly, ensure all parts are present by comparing with the package contents list. Do not proceed if any part is missing or damaged.

Estimated Installation Time: 75 minutes (allow 24 hours for silicone caulk to dry)

Tools Required (not included):

• Wood stud finder
• Phillips screwdriver
• Utility knife or scissors
• Silicone caulk
• Power drill with drill bit

Helpful Tools (not included):

• Measuring tape
• Level

Assembly Instructions:

Locate the wood studs and pre-drilling holes for screws
Use a wood stud finder to locate the wood studs behind the walls. Mark the installation location for the cleats on wood studs.
Ensure cleats are level before installing.

Installing the wall hanging cleats
Attach the wall hanging cleats to the wall using provided screws. Ensure cleats are level.

Hanging the vanity
With the help of another person, carefully hang the vanity onto the wall- hanging cleats.

Reinforcing the vanity to the wall
Open the doors of the vanity and use the provided screws to reinforce it to the wall where wood studs are located.

ORIGIN21 and logo design are trademarks or registered trademarks of LF, LLC.
All rights reserved.

ITEM #5501915

5530622

MODEL #TJ-0328V4822BLU

TJ-0328V4822BR

ATTACH YOUR RECEIPT HERE Serial Number
Purchase Date

Thank you for purchasing this ORIGIN21 product.
Questions, problems, missing parts?
Before returning, contact us on:
888-251-1026, 8 a.m. – 8 p.m., EST, Monday-Sunday or ascs@lowes.com.

PACKAGE CONTENTS

HARDWARE CONTENTS (not shown actual size)

Ø5×60 mm Screw
Qty. 12+2 extra

SAFETY INSTRUCTION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• Unpacking requires two adults and several steps are more easily handled with two adults.

CAUTION

• DO NOT try to pry off top from vanity, as damage to top or vanity may occur. Follow these instructions closely, take your time, and use care while assembling this vanity.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Installation Time: 75 minutes (24 hours for silicone caulk to dry).
Tools Required for Assembly (not included): Wood stud finder, Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with drill bit.
Helpful Tools (not included): Measuring tape, level.

ASSEMBLY INSTRUCTIONS

Locate the wood studs and pre-drilling holes for screws

• Use a wood stud finder to locate the wood studs behind the walls.
• The vanity could be moved right and left as long as the wall hang cleat could be attached to wood studs.
• Use a pencil to mark the installation location for the cleats (F) on wood studs only. Use a level to ensure the cleats (F) will be level before installing to the wall.
• Pre-drill Ø4x48mm deep holes for 1st and 3rd screw rows, and Ø4x30mm deep holes for 2nd and 4th screw rows.
• Note:
  • Pre-drill holes for screw on wood studs only. Don’t need to screw with other holes of wall hanging cleats which not aligned to wood studs.
  • Make sure that the hangers and vanity back frame do not block any water sources and drain pipes.

Installing the wall hanging cleats
With the beveled edges facing up, attach the two wall hanging cleats (F) to the wall with the 1st and 3rd screw rows using the 6 screws (AA) provided. Use a level to ensure the cleats (F) is level.

Hardware Used

AA Ø5×60 mm Screw x6

Hanging the vanity

• With help from another person, carefully hang the vanity (A) onto the wall hanging cleats.

Reinforcing the vanity to the wall

• Open the doors.
• Use 6 screws (AA) provided to reinforce the vanity to the wall where the wood studs located.

Hardware Used

AA Ø5×60 mm Screw x6

Installing the sink template

• Place two of the sink templates (E) on the vanity top (B).
• Align hole in sink template (E) with two of the holes in the vanity top (B).
• Make sure the sink template (E) is flush with the back edge of vanity top (B).

Appling silicone caulk

• Apply a thin bead of silicone caulk (not included) onto the vanity top (B) close to the edge of the sink cut out as pictured.

Installing the sink

• Gently lower two sinks (D) onto the vanity top (B),ensuring the sink over-flow holes is positioned at the front of vanity base (A).
• If needed, immediately use water to clean up any excess silicone caulk.

Adjusting the doors up or down (step 8 - > 10) (optional)

• Loosen screws (a) on both hinges.

Adjusting door up or down.

Retightening screws (a).

Adjusting the doors left or right (optional)
Turn screws (b) on both hinges.

Adjusting the doors in or out (step 12 - > 14) (optional)

• Loosen screws (c) on both hinges.

Adjusting the doors in or out.

Retightening screws (c).

Applying silicon to the Backsplash (step 15 - > 17)
Apply silicone to the unpolished back side and bottom of the Backsplash (C). Place the Backsplash (C) on the vanity (A). Be sure to align the Backsplash (C) with the top (B) of the vanity (A).

Removing silicon to the Backsplash
Gently remove excess glue from the connecting area.

Needing time for silicon to be dried
Let the vanity and backsplash sit for 24 hour before use.

Installing the faucet (not included in the package)

Note: Make sure the thread of the faucet (L) is long enough to fix to the vanity top and connect the water system.

• Installing the faucet base on your own faucet instruction.

Removing top – reinstalling/replacing top (step 19 - > 22) (optional)

lf you need to remove the top for any purpose, do so in the following manner:

• Open the doors.

Note: When vanity top is preinstalled.

Removing the top
Use a screwdriver (not provided) to unscrew these 18 wood screws (d), and place them face up onto a scratch free surface such as a foam sheet that came in the packaging.

Placing the top on the vanity

• Place the top on the vanity. Make sure it averages each side and is flush with the back.

Re-installing or replacing the top
Use a screwdriver to secure (d) these 18 wood screws.

CARE AND MAINTENANCE

• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product. You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local supplier.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g. granite, marble, engineered stone). Stone tops will vary from product to product. Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster or similar item to protect the surface if placing any soap or fragranced products on the stone.
• If soap or fragranced products come in contact with the stone top, rinse the surface with water and dry using a soft non-abrasive cloth.
• WARNING: Must use cleaning agents safe for stone. check your cleaning agents use restrictions before using on any stone. Damage to the stone may result. Vanity manufacturer not responsible for damage caused by improper cleaning agents or soaps used. Warranty will not cover damage caused by the use of improper soaps or cleaning agents.
• DO NOT use products to clean the stone top that contain acetone, lemon, vinegar or other acids as these may cause damage to the stone surface.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home store. Follow the manufacturer’s directions on how to apply.

WARRANTY

The manufacturer warrants this item against defects in materials and workmanship for a period of one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser. This warranty does not apply to any damage on the product by accident, misuse, or modified, improper installation or by affixing accessories not produced by the manufacturer. The manufacturer is not accountable whatsoever for product installation during the warranty period. There is no further expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential or special damages arising at or in connection with product use or performance except as may otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

REPLACEMENT PARTS LIST

For replacement parts, call our customer service department at 888-251-1026, 8 a.m. – 8 p.m., EST, Monday – Sunday. You may also contact us at ascs@lowes.com.

NOTE: G (1), H (1) for Item TJ-0328V4822BLU
G (2), H (2) for Item TJ-0328V4822BR

Frequently Asked Questions (FAQ)

Can I assemble the vanity alone?

It is recommended to have assistance when hanging the vanity to ensure safety and ease of installation.

What should I do if a part is missing or damaged?

Do not attempt to assemble the product. Contact customer support for assistance.

Do I need to use silicone caulk during assembly?

Yes, silicone caulk is required for installation. Allow it to dry for 24 hours before using the vanity.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>