WALI M001U Single Monitor Arm Desk Mount Installation Guide
- June 17, 2024
- WALI
Table of Contents
- INSTALLATION MANUAL
- Single Monitor Desk Mount with Bracket Adapter
- M001U
- Supplied Parts List
- [1] Option A : Clamp Installation
- Option B : Grommet Base Installation
- [4] Option A : For 23’’ monitor
- Option B : For 24’’ monitor
- Option C : For 27’’ monitor
- Option D : Less than 23’’ monitor
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INSTALLATION MANUAL
Single Monitor Desk Mount with Bracket Adapter
M001U
WARNING
If you do not understand these directions, or if you have any doubts about the
safety of the installation, please call a qualified technician. Check
carefully to make sure there are no missing or defective parts. Improper
installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
| | |
---|---|---|---
Pole a (x1) | C-Clamp b (x1)| C-Clamp Brace c (x1)| Swivel Arm d (x1)
| | |
VESA Plate e (x1)| M5x14 Bolt f (x3)| M8x12 Bolt g (x2)| Nut h (x1)
| | |
M10 Bolt i (x1) | Support Plate j (x1)| M10 Washer k (x1) | Spring Washer l
(x1)
| | |
Grommet Base Plate m (x1)| Wire Clip n1 (x1)| Wire Clip n2 (x2)| Allen Key o
(x1)
| | |
Wrench p (x1)| M4x12 Bolt q (x4)| M4x30 Bolt r (x4)| M4 Spacer s (x4)
| | |
---|---|---|---
Bracket ① (x4)| Connector ② (x4)| Cover ③ (x4)| M6X80 A (x4)
|
| |
M6X60 B (x4)| M6X40 C (x4)| (x8) D| (x8) (x1) E
[1] Option A : Clamp Installation
Connect Pole a and C-Clamp Brace c from the bottom using M5x14 Bolt
f and tighten with Allen Key 3mm o.
Select the preferred height according to your desk thickness. Connect C-Clamp
b to C-Clamp Brace c using M8x12 Bolt g and tighten with Allen Key
5mm o. Rotate the hand knob clockwise to fasten for stability.
- Hand Knob
Option B : Grommet Base Installation
1. Place Pole a onto Grommet Base Plate m. Connect them from the bottom using M5x14 f Bolt and tighten with Allen Key 3mm o.
2a. Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount. Position the Pole a on the mounting surface and secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i . Fasten the Bolt using the provided Wrench p.
2b. Self-drilled Grommet Hole Installation
Mark the position of the hole on your mounting surface. Drill a 3/8″ (10mm) diameter hole at the marked position through the mounting surface. Position the Pole a on the mounting surface and secure using the Support Plate j , M10 Washer k , Spring Washer l , and M10 Bolt i. Fasten the Bolt using the provided Wrench p.
[2]
Put the Wire Clip n1 and Swivel Arm d through the Pole a , adjust
the preferred height and tighten using Allen Key 6mm o . Attach the Wire
Clips n2 to the Swivel Arm d.
Optional: For Monitors with VESA Mounting Holes on the Back.
Please skip this step if your monitors do not have mounting holes on the back.
Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten with a screwdriver. (Screwdriver not included).
Step 1 Select Monitor Screws
Only one screw size fits your Monitor
M4x12 M4x30
Hand thread screws into the threaded inserts on the back of your Monitor to determine which screw (M4x12 or M4x30) to use.
Step 2 Select Spacers ( if needed )
NOT NEEDED
- Flat Monitor
NEEDED FOR
- Inset Holes
- Round Monitor
Step 3a Flat Back Monitor
Step 3b Curved or Recessed Back Monitor
[3]
Select the right size of bolt ( A B C ) according to the thickness of your
monitor. Attach the Connector and bolt ( A B C ) to the Bracket. Please do
not over tighten.
[4] Option A : For 23’’ monitor
- Nut
Option B : For 24’’ monitor
1.
- Nut not needed
- Nut
- do not tighen
- tighen
2. Please make sure the bottom brackets hold the monitor firmly. Slide the upper bracket to the side until it is fixed. Finally tighten the Nut for stability.
a tighen
Option C : For 27’’ monitor
1.
- Nut
- Nut not needed
- do not tighen
2. Slide the bottom bracket to the side until it is fixed. Slide the upper bracket to the side until it is fixed. Please make sure the brackets hold the monitor firmly. Finally tighten the Nut for stability.
- Nut
- tighen
Option D : Less than 23’’ monitor
1.
- Nut not needed
- Nut
- do not tighen
2. Slide the brackets until it is fixed. Please make sure the brackets hold the monitor firmly. Tighten the Nut for stability.
Nut
tighen
[5]
Put the assembled TV/Monitor onto the Swivel Arm d and tighten the VESA
Plate e with Nut h for stability. Adjust the tilt angle using Allen
Key 5mm o.
[6]
Tighten the Bolt to fix the connector.
[7] Guide the cable through the Wire Clips ( n1 , n2 ) and store the Allen Keys o in the Wire Clip n1. Manually swivel, tilt, and rotate the monitor for the best viewing angle.
Notice: Please make sure the security nut h is installed before you rotate the monitor.
www.walielectric.com
support@walielectric.com
1-844-SATTLER (18447288537)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>