TROY LIGHTING B4913 Corning Tall Wall Sconce Instruction Manual

TROY LIGHTING B4913 Corning Tall Wall Sconce

Product Specifications:

• Brand: Hudson Valley Lighting
• Model: Corning B4918
• Max Wattage: 8 watts (Type B lamp)

Product Usage Instructions

Fixture Installation:

1. Determines the location for the lamp and mark hole locations for wall anchors.
2. Drill holes for wall anchors and install them.
3. Attach the mounting plate onto the junction box using mounting screws.
4. Securely attach the ground wire to the ground inside the outlet box or grounding screw on the mounting plate.
5. Connect the white fixture lead to the neutral wire and fasten with a wire nut and electrical tape.
6. Connect the black fixture leads to the hot wire and secure the connection.
7. Apply weatherproof caulking or silicone sealant around the inside edge of the back to prevent water entry.
8. Attach the fixture assembly to the mounting plate using fixture mounting screws.
9. Install the glass by pushing the clip to hold it in place.
10. Screw the recommended type B bulb into the socket of the fixture, ensuring not to exceed the maximum wattage.
11. Restore power at the breaker or fuse box.

Frequently Asked Questions (FAQ):

• Q: What is the maximum wattage for the bulb in this fixture?
  A: The fixture is rated for a maximum of 8 watts with a Type B lamp. Do not exceed this recommended wattage to avoid damage.

• Q: How should I prevent water from entering the outlet box?
  A: Apply a bead of weatherproof caulking or silicone sealant around the inside edge of the back of the fixture to create a water-tight seal. Do not plug the drain hole.

• Q: Why is it crucial to correctly connect the ground wire and other wires during installation?
  A: Failure to follow proper wiring instructions could result in serious injury or death due to potential short circuits or electrical hazards. Always ensure proper connections according to the provided guidelines.

WARNING/CAUTION

• DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
• TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURES MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY-TRAINED TECHNICIAN.
• CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM. WASH HANDS AFTER USE.
• UNPACK THE FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE BEFORE INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
• PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.

FIXTURE INSTALLATION

1. Determine the location for the lamp. Using the mounting plate as a template, mark the location of the holes for the WALL ANCHOR (F).

2. Drill the appropriate size holes for the WALL ANCHOR (F). (the holes should be slightly smaller than the size of the anchors.) Install the wall anchors to the hole.

3. Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on a standard junction box. The junction box must be securely mounted to the structure of the building. Screw in the WOOD SCREW (E) to the WALL ANCHOR (F).

4. Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bare copper wire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEVER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH

5. Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connection seals the end of the fastener. MAKE SURE
   THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT- CIRCUIT

6. Connect the black fixture to the hot (Generally black) wire in the junction box. Fasten the joined wires the same as the previous step. NEVER REVERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH

7. To prevent water from flowing into the outlet box, put a bead of weatherproof caulking or silicone sealant around the inside edge of the back. DO NOT PLUG THE DRAIN HOLE (K)

8. Attach the FIXTURE ASSEMBLY (H) to the MOUNTING PLATE (A) and secure with the FIXTURE MOUNTING SCREWS (G).

9. Install the GLASS (J) to the fixture. pushing the clip to hold the glass.

10. Screw the BULB (I) into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR A MAX WATT TYPE B LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE

11. Restore power to the outlet at the breaker or fuse box.

REPLACEMENT PART NAME

www.hvlgroup.com

References

• Hudson Valley Lighting Group

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>