TROY LIGHTING F2324 MAESTER 16 Wide Woven Abaca Pendant Instruction Manual
- June 1, 2024
- TROY LIGHTING
Table of Contents
HUDSON VALLEY
LIGHTING GROUP
Hudson Valley Lighting । Troy Lighting । Mitzi । Corbett Lighting
F2324 MAESTER 16 Wide Woven Abaca Pendant
WARNING/CAUTION
-
DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
-
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION AND MAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
-
CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER USE. -
UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANY DAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
-
PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
MAESTER F2324
Installation Instructions
| PART(S) | REPLACEMENT PART NAME | NUMBER |
|---|---|---|
| A,B,C,D,E,F,G | HARDWARE KIT | HDW-04 |
| H,I,J | CANOPY ASSEMBLY | CAS-F216 |
| K | CHAIN | CHN-PN1010-SET |
| M | THUMB SCREW | SCR-F2316 |
| O | SHADE | SHD-F2324 |
| P | GLASS | GLS-F2324 |
FIXTURE INSTALLATION
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). This fixture is designed to be mounted on standard round or octagon junction box. The junction box must be securely mounted to the structure of the building.
- Remove the SCREW COLLAR (I) from the COLLAR LOOP (H). Fully thread the NIPPLE (C) onto the COLLAR LOOP (H). Thread the HEX NUT (E) onto the NIPPLE (C) along with TOOTH WASHER (D). Then thread the NIPPLE (C) onto the MOUNTING PLATE (A). Adjust the NIPPLE (C) so that the threads of the COLLAR LOOP (H) extends 1 4″ beyond the CANOPY (J). Secure using HEX NUT (E).
- Place the SHADE (O) on top of the FIXTURE ASSEMBLY (L) then lift the FIXTURE ASSEMBLY (L) making sure that the SHADE (O) is properly hanging.
- Open the end link the of the CHAIN (K) and attach to the FIXTURE ASSEMBLY (L) at the desired height. Slide the SCREW COLLAR (I) and the CANOPY (J) onto the CHAIN (K). Open the link on other end of the CHAIN (K) then attach unto the COLLAR LOOP (H). Feed the wires through the CHAIN (K) , SCREW COLLAR (I), CANOPY (J), COLLAR LOOP (H), NIPPLE (C), and MOUNTING PLATE (A).
- Cut off excess wires, and strip the insulation off the end of the leads.
- Attach the Ground wire to the ground inside the junction box (Generally green or bare copper wire) or the GROUND SCREW (F) on the MOUNTING PLATE (A). NEER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Connect the fixture’s SPT Neutral (SPT WIRE WITH NO WRITINGS) wire lead to the neutral (Generally white) wire in the outlet box. Fasten the wires together with an approved fastener (WIRE NUT) (G). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURE THERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
- Connect the fixture’s SPT hot (SPT WITH WRITNGS) wire lead to the hot (Generally black) wire in the junction box. Fasten the joined wires same as previous step. NEER REERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Push the wires back into the junction box. Lift up the CANOPY (J) up to the ceiling, and screw the SCREW COLLAR (I) onto the COLLAR LOOP (H).
- Screw the BULB (N) up into the SOCKET of the FIXTURE ASSEMBLY (L). THIS FIXTURE IS RATED FOR 25 WATT TYPE A21 LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE
- Carefully lift up the SHADE (O) then attach the GLASS (P) onto the FIXTURE ASSEMBLY (L) and secure using THUMB SCREW (M). Let the SHADE (O) slide down gently.
- Restore power to the OUTLET at the breaker or fuse box.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>