HALO IB518183ML 4 Inch Round & Square LED Directional Fixture Fitting Instruction Manual

HALO IB518183ML 4 Inch Round & Square LED Directional Fixture Fitting

Specifications

• Model: IB518183ML
• Dimming Compatibility: 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers
• Color Temperature Options: 2700K, 3000K, 3500K, 4000K, 5000K
• Installation: Directly into ceiling without separate JBOX or recessed housings

Product Usage Instructions

Safety Instructions Before attempting installation, ensure compliance with local electrical codes and turn off power supply at the fuse box or circuit breaker.

Wear gloves to handle sharp edges during installation.

Dimming The Halo HLA is compatible with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Refer to the manufacturer for specific dimmer compatibility and application details.

Installation Method The HLA models can be installed directly into the ceiling without the need for separate JBOX or recessed housings.

Wiring Instructions

1. Cut an opening in the ceiling using the provided template.
2. Insert supply wires through the strain reliefs in the provided jbox.
3. Connect ground wires and black/white leads as instructed using provided wire nuts.
4. Secure the supply wire to the jbox and close the cover before installation into the ceiling.

FAQ

Q: What should I do if I encounter difficulties during installation?

A: If you face challenges during installation, it is recommended to contact a qualified electrician for assistance to ensure safety and proper installation.

Q: Can I use the product with any dimmer?

A: The Halo HLA is designed to work with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. It is essential to consult the dimmer manufacturer for specific compatibility details.

Q: How do I select the desired color temperature?

A: The product comes with a selector switch offering options for color temperature (2700K, 3000K, 3500K, 4000K, 5000K). Simply choose your preferred setting using the switch.

IB518183ML

HLA4 – 4” Round & Square LED Directional Fixture Fitting

Packaging Contents

ITEMS REQUIRED
(Purchase separately)

Gloves

Selector Switch (2700K, 3000K, 3500K, 4000K, 5000K) Choose your favorite correlated color temperature (CCT) from 5 options using the switch

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

• Heed all warnings, including below warnings AND those included on product.
• HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.

WARNING

Read and follow these instructions.

• Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS.
  If uncertain, consult an electrician.

• Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

• Risk of Fire/Electric Shock – LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.

  • Install this kit only in the luminaires that have the construction features shown in the photographs and/or drawings.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION

Edges may be Sharp – Wear gloves while handling.

• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.

• Fixture should be installed by persons with experience in household wiring or by a qualified electrician.
  The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • this device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation.

• Only those open holes indicated in the photographs and /or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
  SAVE THESE INSTRUCTIONS AND WARNINGS.

DIMMING

Halo HLA is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. Note some dimmers require a neutral in the wallbox.) For the latest Halo HLA product information, please refer to specifications online at
www.cooperlighting.com.

DETERMINING WHICH INSTALLATION METHOD TO USE

The HLA models can be installed directly into a ceiling without requiring separate JBOX or recessed housings.

WARNING

Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

WIRING

1. Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1). Make sure the opening is not larger than the outer flange of the LED module. A hole saw is recommended.
2. Open the cover of the provided jbox and insert the supply wires through the preferred strain reliefs in the provided jbox (Fig. 3a). Connect the bare copper (ground) wire from the jbox to the ground wire of the supply connection using the provided wire nut (see Fig. 3b).
3. Connect the black/white leads from the output of the driver to the appropriate supply side wiring using the provided wire nuts.
4. Close the cover after properly securing the supply wire to the provided jbox on the rear of the LED module.
5. Module is ready to install into ceiling.
   (See MOUNTING section for specific instructions).

MOUNTING

1. Connect the remote driver box to the light fixture. (Fig. 2a)
2. Place remote driver box thru the cut-out hole and mount according to local code as required. (Fig. 2b)
3. Bundle any excess wire and place into ceiling above the module according to local code as required.
4. Rotate both mousetrap springs upward to allow passage through the cutout in the ceiling (Fig.4).
5. Continue to press the module through the cutout in the ceiling until the perimeter flange of the module is flush against the ceiling.
6. The springs will rotate back into position and hold the LED module tight the ceiling.

Note: For use with new construction mounting frame, insert jbox into ceiling hole and slide box into position (see Fig. 2C).

AIMING

1. Tilt the fixture towards a desired target (Fig. 5)

REMOVAL

CAUTION
Risk of pinching –
Do not place hands or fingers under springs during removal of the LED module.

1. Simply and slowly pull down firmly on LED module until mousetrap springs release from the ceiling. Reach through the ceiling to hold mousetrap springs up and away from the ceiling as you continue to pull the module from it’s opening.
2. Disconnect wiring.

5-YEAR LIMITED WARRANTY

• THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
• Cooper Lighting Solutions (“CLS”) warrants to customers that, for a period of five years from the date of purchase, CLS products will be free from defects in materials and workmanship. The obligation of CLS under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product. A purchaser’s receipt or other proof of date of original purchase acceptable to CLS. This is required before warranty performance shall be rendered.
  This warranty does not apply to CLS products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by CLS which have been supplied, installed, and/or used in conjunction with CLS products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:

• IN NO EVENT SHALL CLS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF CLS FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF CLS PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF CLS PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

• All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused.
  CLS is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

• Reproductions of this document without prior written approval of CLS are strictly prohibited.

Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269 www.cooperlighting.com

© 2020 Cooper Lighting Solutions All Rights Reserved
Printed in USA

Cooper Lighting Solutions is a registered trademark.
All trademarks are property of their respective owners.

HLA4 Round Ceiling Template

HLA Series Instructions
www.cooperlighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>