baby brezza BRZ0103_EU Bottle Washer Pro Instructions

Baby brezza BRZ0103_EU Bottle Washer Pro

Product Information

Specifications:

• Heating Power: 800W
• Drying Power: 180W
• Model: BRZ0103
• Supply Voltage: 220-240V ~ 50/60Hz

Product Usage Instructions

1. Make sure the Intake Filter is placed at the bottom of the sump.
2. Line up the rib on the tube of the Bottom Spray Jets with the slot on the hole in the base.
3. Push the Bottom Spray Jets all the way down on the base.
4. Place the Bottom Rack on the Base, over the Bottom Spray Jets.
5. Fit Center Tube on the Bottom Spray Jets. Use the short tube for short bottles or the tall tube for tall bottles.
6. Line up the rib in the Top Spray jet with the Center Tube and push the Top Spray Jets down.

FAQ

1. What should I do if I encounter a lid warning?
   The lid warning turns on if the start button is pressed without the lid in place, if the lid is opened during operation, or if the lid is not closed completely. Make sure to close and secure the lid properly before starting the operation.

2. How do I address low water in the clean water tank warning?
   If the “Low Water in Clean Water Tank” warning turns on, ensure that the water is filled to the FILL line before pressing the start button to begin the operation.

3. How can I clear the descaling reminder?
   The descaling reminder turns on after 20 uses to remind you to descale the heater plate. Follow the descaling instructions provided in the manual. Press and hold the wash mode button for 5 seconds to clear the descaling reminder.

IMPORTANT:
Only use Baby Brezza Detergent Tablets. Do Not USE any household dishwasher detergent. FREE Baby Brezza Detergent Tablets included!

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions carefully before using your bottle washer.

2. Ensure that the supply voltage marked on the appliance corresponds with your main supply.

3. If there is any visible damage to the appliance, the plug or the supply cord, disconnect the appliance immediately and do not use it.

4. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or a similarly qualified person to avoid a hazard.

5. Do not allow children to touch or use the appliance. The appliance becomes very hot and the steam can cause severe scalding.

6. Do not move the appliance when it is in use because it contains hot liquids.

7. Do not touch the hot surfaces on the appliance.

8. Do not place the appliance on or near hot surfaces, in a heated oven or near a gas or electric heater.

9. Unplug the appliance from the power supply before cleaning or storage.

10. Do not immerse the supply cord, plug or base unit in water or any other liquid.

11. This appliance does not contain any user-serviceable parts inside. Do not dismantle.

12. This appliance is for indoor household use only. Do not use outdoors.

13. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

14. This appliance has a polarized plug (one blade wider than the other). To reduce the risk of electric shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

15. a) A short power cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
    b) Extension cords are available and may be used if care is exercised in their use.
    c) If an extension cord is used: The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance; The longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or pulled on unintentionally (especially by children).

16. Children should be supervised to ensure that they do not play with the appliance.

17. Do not use it for space heating purposes.

18. Always use on a level heat-resistant surface.

19. Always keep the Bottle Washer and its plug out of reach of small children.

20. To disconnect the power cord, turn the appliance off first, then remove the plug from the power outlet.

21. Always unplug from the electric outlet when not in use. Allow to cool before putting on or taking off any parts.

22. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or adjustment.

23. The use of accessory attachments is not recommended by the appliance manufacturer as this may cause injuries.

24. This bottle washer is Intended for use in residential homes, hotels and other similar lodging and offices/office break rooms.

25. Do not open while in use as this product contains boiling water. Beware of escaping steam from the vent holes in the lid.

26. Allow at least 30 minutes between uses and make sure the unit has been cooled down before using again.

27. Steam escaping from the unit can cause burns. Always allow 5 minutes to cool down after the cycle finishes before lifting the lid.

28. KEEP CHILDREN AWAY from this bottle washer at all times.

29. To provide continued protection against the risk of electric shock, connect to properly grounded power outlets only.

30. CAUTION: Risk of electric shock, disconnect electric power before servicing.

31. Any servicing should be performed by an authorized service representative. The appliance has no user-serviceable parts.

SAVE THESE INSTRUCTIONS

TECHNICAL DATA

• Model: BRZ0103
• Heating Power: 800W, Drying 180W
• Supply Voltage: 220-240V ~ 50/60Hz

Bottle Washer Pro Parts

Control Panel

LCD Icons

Wash Modes

• Wash & Dry
  One 10-minute wash cycle, three 3-minute rinse cycles, & one 60-minute dry cycle.

• Wash, Sterilize, Dry
  One 10-minute wash cycle, three 3-minute rinse cycles, one 9-minute sterilize cycle, and one 60-minute dry cycle.

• Wash Only
  One 10-minute wash cycle and three 3-minute rinse cycles.

Warnings and reminders

• Lid Warning
  Turns on if the start button is pressed without the lid in place, if the lid is opened during operation, or if the lid is not closed completely.

• Low Water in Clean Water Tank
  Turns on if the water is not filled to the “FILL” line when the start button is pressed.

• Water in Waste Water Tank
  Turns on if there is wastewater in the tank when the start button is pressed or turns on when the waste water tank is full.

• Waste Water Tank Not in Place
  Turns on if the waste water tank is not on the base or not inserted properly when the start button is pressed.

• Clean Water Tank Not in Place
  Turns on if the clean water tank is not on the base or not inserted properly when the start button is pressed.

• Descaling Reminder
  Turns on after 20 uses to remind you to descale the heater plate. Follow the descaling instructions on page 8 to descale. Press and hold the “wash mode” button for 5 seconds to clear the descaling reminder.

Setting up the Bottle Washer Pro

1. Make sure the Intake Filter is placed at the bottom of the sump.
2. Line up the rib on the tube of the Bottom Spray Jets with the slot on the hole in the base.
3. Push the Bottom Spray Jets all the way down on the base.
4. Place the Bottom Rack on the Base, over the Bottom Spray Jets.
5. Fit Center Tube on the Bottom Spray Jets. Use the short tube for short bottles or the tall tube for tall bottles
6. Line up the rib in the Top Spray jet with the Center Tube and push the Top Spray Jets down.
7. Place the Top Rack on the Top Spray Jets, with the straight edge of the Top Rack facing the back of the machine.
8. The Clean Water Tank can be lifted by the handle. The Waste Water Tank can be pulled out with the handle. Easily turn the machine with built-in wheels on the bottom.

Now you’re ready to put bottles & parts in the Bottle Washer Pro®! See the following pages for set-up & use

Visit babybrezza.eu for set-up videos and more tips.

Setting up for Washing, Sterilizing & Drying

1. Fill the Clean Water Tank to the FILL line with clean water. You can leave the Water Tank on base and fill with a pitcher.
   • Or you can remove the Clean Water tank from the Base and fill it at the sink.
   • Make sure the water is filled to the FILL line at the top edge of the clear part of the Clean Water Tank
2. Make sure the Waste Water Tank is empty and pushed into the base.
3. Remove the Lid by grasping the handle and lifting it straight up.
4. Place up to 4 bottles upside down on the Bottom Rack. Vent tubes or other accessories can be placed over the side jets as shown above.
5. Place nipples and accessories right side up on the Top Rack centred over jets.
   • Bottle parts with small pathways are not recommended for use in the Bottle Washer Pro® and should be cleaned thoroughly by hand with brushes supplied by the bottle manufacturer.
   • Large/wide collars and caps may not fit with the bottles & nipples and should be washed separately.

IMPORTANT:
For best results, please rinse milk, other liquids or solids from bottles and accessories before placing them in the Bottle Washer Pro®.

Adding Detergent and Starting a Wash Cycle

1. Place 1 Baby Brezza Detergent Tablet in the detergent tray. It is OK if it falls out of the tray and into the sump.

2. IMPORTANT
   Do Not Use liquid detergent, household dishwasher detergent or pods. Only use Baby Brezza Detergent Tablets

3. Carefully place the Lid on the Base and make sure it is closed completely.

4. Press and hold the “Power” button for 3 seconds to turn on the Bottle Washer Pro®.

5. Touch the “wash mode” button to choose a wash cycle. See page 3 for details.

6. Press the “Start/Pause” button to start the Bottle Washer Pro®.

   • The machine will start by draining the sump to make sure it starts with clean water, then it will begin filling the sump and heating the water.
   • The LCD will show the icon for each cycle and display a timer countdown When the last cycle is completed, the Bottle Washer Pro® will automatically shut off.

Pausing the Machine:

• You can pause the machine at any time by pressing the “Start/Pause” button.
• Be careful, the Lid may be hot to the touch & steam may escape when you remove the lid.
• The machine will turn off after 20 min if not restarted. You can restart the machine by pressing “Start/Pause” again – we recommend restarting the machine to complete the cycle and drain the sump.

Starting a Sterilize and Dry Only Mode Without Washing

• Sterilize & Dry: Touch the Sterilize-Dry button 1 time, then press the Start/Pause button to start.
• Dry Only: Touch the Sterilize-Dry button 2 times, then press the Start/Pause button to start.
• Sterilize Only: Touch the Sterilize-Dry button 3 times, then press the Start/Pause button to start.

The Bottle Washer Pro® will shut off automatically after finishing the Sterilize and Dry cycles.

The Bottle Washer Pro® uses HOT WATER, STEAM & HOT AIR to wash, sterilize & dry bottles and accessories. USE CAUTION when handling bottles after washing, sterilizing and/or drying.

Empty the Waste Water Tank after Wash/Dry cycle is complete

Water in the Waste Water Tank will be HOT. Always allow cooling time before handling the Waste Water Tank.

• Grip the handle on the back of the Waste Water tank and carefully remove it by sliding it back.
• Gently lift the lid and carefully pour waste water into the sink.
• Rinse and Dry Waste water tank. Then insert it fully into the base of the Bottle Washer Pro®.

Cleaning the Bottle Washer Pro

• Always unplug the Bottle Washer Pro® before cleaning.
• Do not immerse the base or power cord in water or other liquids.
• Do not clean the base under a water faucet.
• Use a soft damp cloth to clean the base and control panel.
• Never use solvents, cleaning products, or abrasive pads to clean the plastic parts of the machine as they may damage the appliance and surface of the base.
• The top cover, bottom rack, and top rack can be cleaned in hot soapy water.
• To clean the intake filter, lift it with the handle and wipe any residue from the mesh.
• If Spray Jets become blocked, disassemble the top and bottom spray jets and centre tube, poke spray jet holes with a toothpick or small brush and rinse with warm soapy water.
• NEVER PLACE PARTS IN THE DISHWASHER, MICROWAVE OR STERILIZER.

Descaling the Bottle Washer

The Descaling Reminder will turn on after 20 washes to remind you to descale the heater plate. Press & hold the “Wash Mode” button for 5 seconds to clear the descaling reminder.

NOTE:
If you have hard water, you may need to descale more often.

Descaling Instructions:

• To remove the mineral scale from the heating plate, pour a mixture of 300ml white vinegar and 300ml water into the sump. Let the mixture sit overnight.
• Fill the Clean Water Tank to FILL line with distilled water and run one “Wash Only” cycle to rinse the system, then dispose of the wastewater.
• The stainless steel heating plate can be gently scrubbed with a scouring pad to remove any remaining mineral scale.

Replacing the HEPA filter

Replacing the HEPA filter – Recommended every 3 months

• First, turn the Bottle Washer on its side to access the HEPA filter which is located on the bottom of the Bottle Washer Pro®. NOTE: some residual water may spill from the sump
• Remove the filter cover by pressing the filter cover tab and lift it up.
• Remove the HEPA filter by pulling the filter tab and throwing away the used filter.
• Install the new HEPA filter with the tab facing up.
• Replace the filter cover by inserting tabs and clicking the latch in place.

Replacement HEPA filters can be purchased atbabybrezza.com

Tips for best use

• Always load nipples facing up so water does not collect inside.
• When placing bottles, accessories or other items in the washer, make sure that water can run off the items and will not collect in product indentations. For example: don’t place bottles or cups right side up or they will fill with water.
• Some bottles have concave bases which will collect water. It is normal to see a small amount of water on the bottom of bottles even after drying. You can tilt the bottle so the water runs off in the Bottle Washer Pro® and let air dry.
• Some nipples may collect water around the outside flange and will not dry completely. You can tilt them so the water runs off and let the air dry.
• Always use Baby Brezza detergent tablets – see page 6 and visit babybrezza.com for more info.
• DO NOT USE any type of liquid, powder or pod detergent for your household dishwasher. These detergents are not properly sized or configured for the Bottle Washer Pro and will create too much foam and leave detergent residue on your products
• If you need to discharge all water from the sump, press and hold the “Wash Mode” and “Sterilize/Dry” buttons for 3 seconds and the discharge pump will pump water from the sump to the waste water tank.

Troubleshooting

Condition

| Possible Cause|

Remedy

---|---|---
Bottle Washer will not start.| The unit is unplugged.| Make sure the plug is securely inserted into the power outlet.
The unit is not turned on.| Touch the power button on the control panel.
Not enough water in the clean water tank.| Add water to the FILL line of the water tank.
Mineral Scale or Discoloring on Heating Plate| Mineral-rich water is used persistently.| Clean the heater plate after each use.
Bottles not rinsed before placed in Bottle Washer causing milk residue to burn on heating plate| Rinse all bottles & accessories before placing them in the Bottle Washer Pro®
| The clean Water Tank is not properly assembled on the base.| Make sure the Clean Water Tank is seated on the base.
| The Waste Water Tank is not properly assembled on base.| Make sure the Waste Water Tank is seated on the base.
| Clean Water Tank is low or empty.| Refill the Clean Water Tank to the FILL line.
| Waste Water Tank is full or holds too much water.| Empty Waste Water Tank.
| Washer Lid is not completely closed or not seated properly.| Make sure the lid is seated completely on the base.
| Descaling is necessary.| Follow the instructions on page 8 to describe the heating plate. Press and hold the “wash mode” button for 5 seconds to clear the descaling reminder
Spray Jets have low pressure| Spray Jets are physically blocked by items in the wash chamber.| Make sure bottles/accessories are centred over Spray Jets and are not blocking holes on jets. Make sure the top and bottom racks are placed correctly on the base.
Spray Jet holes are blocked with debris.| Clean jets with a brush, small pointed tool or toothpick. See the cleaning detail on page 8.
The Spray Jet fixture is not properly assembled.| Make sure all fittings on spray jet fixtures are assembled properly.
The Spray Jet fixture is broken or cracked.| Inspect spray arms for damage and Contact Baby Brezza Customer Care for replacement parts.

If you can not remedy problems by using the troubleshooting chart above, do not return your bottle washer to the store. Please contact Baby Brezza Customer Service (see back page for contact information)

ACTIVATE YOUR WARRANTY

Scan here

babybrezza.eu

Benefits:
Faster customer support, extended customer service hours & more.

Customer Service
If you are experiencing problems with your BabyBrezza Formula Pro Advanced, visit babybrezza.eu to locate your local customer service representative.

babybrezza.eu
© 2023 Baby Brezza Enterprises LLC.

References

• Baby Brezza | Baby Products & Essentials that Make Parenting Easier
• Baby Brezza Europe | Time-Saving Baby Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>