Baby Brezza Formula Pro FRP0045 Food Maker Instruction

Baby Brezza Formula Pro FRP0045 Food Maker Instruction

Silicone Scraper instructions

The silicone scroper should be washed before first use. You can leave It Installed In the Locking Cover when washing. but if you need to remow or replace ii, follow the installation below.

• To Remove: Gently pull the scraper from the top to remove and slide out of slot in Locking Cover.
• To install: Align scraper with slot in Locking Cover and push gently into slot.
• While pulling from the bottom side, push on the top side to seat the first barb.
• Continue pushing down along the top of scraper while gently pulling to seat all barbs
• When the Scraper is fit properly, the top will sit flush with the Locking Cover. Check for proper fit by comparing to drawing above.
• Check the direction of the scraper when fit in the locking cover. When viewed from the bottom of the Locking Cover, the Silicone Scraper should fit underneath without protruding as shown in the illustration above.

A FAILURE TO SET UP AND CLEAN THE FORMULA PRO® CORRECTLY WILL RESULT IN IMPROPER FORMULA DISPENSING.

READ THE INSTRUCTION
MANUAL and CAREFULLY follow the step-by-step directions for cleaning, set up and use.

Instructions for safe use

• The appliance must not be immersed.
• Household use only.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are aged from 8 years and above and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
• Children should be supervised to ensure that they do not play with the appliance.

This marking indicates that products should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or Contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

A WARNING:
For infants less than 6 months old, always use bottled water suitable for infant formula preparation. Tap water and/or unsterilized baby bottles can potentially lead to adverse effects for the health of your baby. Only prepare one bottle at a time, feed immediately and follow all instructions carefully. Do not keep leftover formula mix. Always hold baby while feeding. Leaving baby unattended may cause choking. Tap water should be boiled before use to sterilize it.

TECHNICAL DATA

• Supply voltage: 220V-240V 50/60Hz
• Model: FRP0045
• Heater Power: 500W
• Motor Power: 20W

Formula Pro® Controls & Indicator Lights

Formula Pro® Components

Powder Container set up

wash: Funnel, Funnel Cover, Inside of WaterTank,and all Powder Container parts (see page 2). After washing, make sure all Powder Container parts are COMPLETELY DRY before assembly.

Set up the Measuring Wheel to work with your powder type.

1. Press upper & lower halves of Measuring Wheel together so your powder’s setting numbet’ shows through window on the Upper Measuring Wheel. You have now assembled your Measuring Wheel. Set up the Powder Container and parts.
   Correct assembly is critical to accurate powder dispensing

2. Place Powder Container on Base with “MIN” & “MAX” lines facing front.

3. Place assembled Measuring Wheel In Powder Container.

4. Don’t add powder yet.
   Follow the steps on the next page to run an intemal cleaning cycle BEFORE using the Formula Pro<D with powder.

5. Locking Cover should look like this when assembled properly. Make sure the front edge of Locking Cover is under the tab in the Powder Container.

6. Place Stirring Wheel In Powder Container, align with axle and push down so it touches the Locking Cover.

Clean internal parts – before first use – without powder

After setting up the powder container, run a cleaning cycle to rinse internal parts.

1. Place Powder Container Lid on Powder Container as shown.
2. Turn Powder Container Lid Clockwise to lock into place.
3. Plug in machine and turn power switch to on position.
4. Fill water tank to MAX line with distilled water.
5. Place 300ml or larger container to catch water.
6. The Formula Pro® will stop after dispensing 300ml of water. Dispose of the water captured in the container.

Your Formula Pro® is now ready to use with powder.

Follow the steps on pages 5 and 6 to prepare bottle with the Formula Pro®

Always use a clean and sterilized bottle, nipple or other feeding equipment. Wash and dry hands before handling sterilized bottles. Make each bottle as needed,and do not store mixed formula for later use.

Bottle Preparation

Follow the steps on these pages to prepare bottles with the Formula Pro®

Pour powder loosely and evenly into Powder Container. Never fill past1he MAX line. Never pack powder in 1he Powder Container or overfill. Powder can be spread evenly with the 3 anns on 1he Powder Container Lid before closing.

Temperature Indicator Lights

About water temperature

The heat« in the Water Tank will warm the watef and keep it warm as long as the machine Is powet’ed on. ff you reflll the WaterTankwlth cool or room temperature water and need to use the machine right away, !he machine can be used while water Is hea1fng (flashing yellow light). ff you run the machine with cool or room temperature water, before the water Is wann and ready, always make sure formula Is mixed properly and check for dumps.

For quickest warming time, always fill the water tank with room temperature or cool water. Flashing green & yellow lights mean the water poured into in the Water Tank is too hot or too cold. The machine will not work while the green & yellow lights flash. If you don’t want to wait long for the water to heat, do not fill with water stored in the refrigerator.

Never fill the Water Tank with hot water. If you boil water before using it in the machine, let the water cool to body or room temperature before pouring it into the Water Tank.

Never remove Water Tank, Funnel or Powder Container while machine is in operation. Always hold the bottle when feeding baby. Never prop the bottle up and leave your baby to feed unsupervised After baby stops feeding from bottle, discard any leftover formula mixture.

Daily Cleaning – EXTREMELY IMPORTANT!

Unplug the appliance before cleaning. Do not use abrasive pads to clean the machine. The Funnel,Funnel Cover and underside of Powder Container MUST BE CLEANED once per day (if machine is used daily). Follow these steps to clean the Formula P~ parts every day.

1. Remove Funnel & Funnel Cover by pulling out and down.
2. Remove Funnel CDver from Funnel by lifting up on Funnel Cover.
3. wash and rinse runners runner cover thoroughly. Funnel and Funnel Cover are top-rack dishwasher safe and are also sate form.
4. Wipe die hole die on the underside of Lll before Powder Container. With the Funnel removed and Powder Container attached to machine, wipe any dry formula powder from the hole on the underside of the Powder Container & Funnel Compartment in a circular motion with a DRY paper towel or DRY soft doth.

Monthly Cleaning

The Powder Container paru, Water tank and Base should be cleaned once a month.

1. The Powder Container and Powder Container Parts should be cleaned once a month by emptying any remaining powder (powder can be saved for refill) and cleaned with mild detergent and soft cloth or sponge. NEVER PLACE POWDER CONTAINER IN DISHWASHER.
2. The Water Tank should be cleaned once a month with mild detergent and soft cloth or sponge. Rinse inside of Water Tank thoroughly before refilling with clean, purified water. Wipe the outside of the Water Tank with a damp clean cloth. Never immerse Water Tank or get the electronics in the base of the Water Tank wet. If the electronics in the base of the Water Tank get wet, allow to air dry thoroughly before placing back on base. Never place Water Tank in dishwasher.
3. The machine Base should be wiped with a damp, soft cloth or sponge and dried immediately. Never submerge the base or plug in water or other liquids. Dry machine Base after cleaning.

User Tips

• Always make sure powder level is above the top of the Stirring Wheel. You will know it’s time to refill the Powder Container when any of the four horizontal arms of the Stirring Wheel are visible through the powder. Do not use the machine when the powder level is below the MIN line marked on the Powder Container.
• To easily separate the Upper Measuring Wheel from the Lower Measuring Wheel, press the raised center area while holding the outside edge as shown in photo at right.
• Do not remove the Water Tank from the base to refill. Simply lift the Water Tank Lid at the front and pour water in. Make sure to keep water above “MIN” line. Refill Water Tank regularly with room temperature water and keep machine powered on. This way, the water will always be warm and ready to serve.
• If the powder forms a cone shape mound when refilling the Powder Container, use the 3 arms on the bottom of the Powder Container Lid to gently level the powder before closing. Always keep the powder level below the MAX line and never pack powder in the Powder Container.

The Formula Pro can be used at any time during the water heating cycle, but not all powders mix well with cool or room temperature water. Always check for clumps & shake or stir the closed bottle gently to mix the powder completely with the water.

Troubleshooting

If you can not remedy problems with the machine by using the troubleshooting chart above,
please contact Customer Service at:
PHONE : +2711 430 5600
E-MAIL: babybrezza@artemisbrands.co.za

Baby Brezza Formula Pro FRP0045 Food Maker Instruction

Download PDF:Baby Brezza Formula Pro FRP0045 Food Maker Instruction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>