BEGA 84 759 Bollard Tube With PIR And Light Sensor Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 84 759 Bollard Tube With PIR And Light Sensor
Product Information
Specifications
- Model: 84 759
- Type: Mounting Plate
- QR-Code: 655 200
Product Usage Instructions
Safety
The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning should only be carried out by a qualified electrician to avoid damage due to improper use or installation. Any modifications should be done by authorized personnel.
Installation
- Open the connection box.
- Lead the mains supply cable into the connection box.
- Connect the phase to the L1 marked terminal, the neutral wire to the N marked terminal, and the earth conductor to the PE marked terminal.
Circuit Variants
The luminaire can be configured and controlled individually. Forwarding of the switching signal to additional luminaires can be achieved via the relay contact L’.
Commissioning
The power supply must be connected for the commissioning of the luminaire. The brightness sensor will need up to 10 minutes after activation of the power supply to calibrate correctly. Factory settings include Mode: PIR and light, PIR sensitivity: 100%, Shut-down delay: 5 minutes, Brightness threshold: 32.
Control of the Luminaire (on/off)
The luminaire can be controlled for on/off functionality.
FAQ
Q: Can the luminaire be controlled via smartphone?
A: Yes, the integrated PIR motion and light sensor can be configured via smartphone or tablet using the free BEGA Tool app. The default values can be reinstated at any time via the app.
Q: What should I do if the light sensor responds with a delay?
A: The integrated light sensor operates with a time delay to prevent responses to short-term brightness fluctuations. Manual darkening of the sensor will not result in an immediate response.
Bollard tube with PIR and light sensor
Instructions for use
Application
Bollard tube ø 140 mm with integral passive infrared motion sensor and light
sensor.
For usage in the modular system bollard range. The integrated passive infrared
motion and light sensor responds to heat emission in the dark and therefore
activates in case of human or animal movement in the vicinity of the
luminaire. Programming can be carried out using a smartphone or tablet via the
free BEGA Tool app.
Safety
- The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
- The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.
EU Declaration of Conformity
BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 84 759
complies with Directive 2014/53/EU (RED). The complete text of the EU
Declaration of Conformity is available at the following Internet address:
https://www.bega.com/conf/de/84759
Product description
-
Bollard tube made of aluminium
-
BEGA Unidure® coating technology
-
Mounting plate made of cast aluminium for bolting onto a foundation or an anchorage unit
-
Mounting plate with two pitch circles:
-
ø 70 mm, 3 elongated holes 7 mm wide
-
ø 100 mm, 3 elongated holes 9 mm wide Passive infrared motion sensor (PIR)
-
Range up to 12 m
-
Opening angle 120°-150°
-
Decals for reducing the detection range are provided
-
Minimum temperature difference between moving object and environment 4 °C
-
Object speed ideally 1 m/s
-
Adjustable sensitivity of the motion sensor (inertia)
-
Shut-down delay adjustable between 5 s and 240 min
-
Light sensor: adjustable value range from darkness to approaching dusk (approx. 150 lx) Fixed pre-set time hysteresis for suppression of undesired switching operations in luminaires during rapid brightness fluctuations Transmission frequency range:
2400-2483.5 MHz -
Maximum transmission output: 10 mW Connection box 71 084 for through-wiring – for 2 cables up to 7 × 6@ Fuse terminal with micro fuse 6,3 A slow ø 5 × 20 mm
-
Luminaire switchable via relay output (on/off) integrated in the sensor module
-
Relay contact with a switching capacity of 2300 W · 10 A
-
Please note the starting current of the switching loads (max. 100 A)
-
Ambient temperature: -25°C to +55°C 220-240 V y 50-60 Hz
-
Safety class I
-
Protection class IP 65
-
dust-tight and protected against water jets only in combination with mounted bollard head or closing head Impact strength IK05
-
Protection against mechanical impacts < 0.7 joule c – Conformity mark
-
Weight: 4.0 kg
Installation
- The luminaire foot must not be below the upper edge of the floor covering. Approximately 500 mm of cable above the mounting surface will suffice for connecting the luminaire to the power supply.
- Undo the screw at the base.
- Rotate and remove the mounting plate.
- In case of installation on a foundation, please observe the following: Wet concrete can be highly alkaline and must not come into contact with the luminaire permanently.
- We recommend draining the installation area and painting it with insulating paint.
- Using the provided mounting materials or other suitable mounting materials, screw-fit the mounting plate to a foundation or anchorage unit 70 894.
- Open the connection box.
- Lead the mains supply cable into the connection box.
- Make connection of the phase with the L1 marked, the neutral wire at the N marked and earth conductor at the PE marked connecting terminal.
Insert bollard head into bollard tube and turn it clockwise as far as it will
go, adjust if necessary and fix with lateral hexagon socket head screw. Pass
the luminaire power supply cable through the top cable entry into the
connection box. Make the earth conductor connection and the electrical
connection. Make sure that the connection cable is correctly assigned.
Connection of the brown wire from the bollard head to the loose terminal (L’).
Close the connection box.
Place luminaire onto mounting plate, align and fix with screw.
Circuit variants
The luminaire can only be configured and controlled individually.
Forwarding of the switching signal to additional luminaires can be achieved
via the relay contact L’ (see circuit diagram 1).
Circuit diagram 1:
The first sensor of a luminaire controls a group of luminaires, while the
second luminaire sensor controls another group.
Circuit diagram 2:
Sensors of multiple luminaires control the same luminaire group.
All luminaires in the group will be switched on as soon as one of the sensors
detects movement.
It is important to note that all sensors within one group are fed via the same
phase.
Commissioning
- The power supply must be connected for the commissioning of the luminaire.
- The brightness sensor will need up to 10 minutes after activation of the power supply to correctly calibrate the brightness value.
- Once installed, the luminaire can be operated immediately in its factory settings; configuration via smartphone will not be required.
- The factory settings as are follows:
- Mode: PIR and light
- PIR sensitivity: 100 % (high sensitivity)
- Shut-down delay: 5 minutes
- Brightness threshold: 32 (approx. 50 lx)
- Alternatively, the integrated PIR motion and light sensor can be configured via smartphone or tablet using the free BEGA Tool app.
- The default values can be reinstated at any time via the BEGA Tool app.
Download the app for Android or iOS and add the luminaire as your starting
point.
The individual QR code required for set-up can be found in the enclosed set
with decals for reducing the detection area.
Store the QR code with your documentation (e.g. at the top of Page 1 in the
instructions for use).
Select the “Share Access” function in the BEGA Tool app if you want to use a
different or additional smartphone for the configuration of the integrated
sensor module or controlling the luminaire head. Alternatively, the luminaire
will have to be reset to factory settings.
Follow the in-app instructions.
Please note:
The integrated light sensor operates with a time delay to prevent responses to
short-term brightness fluctuations in the environment
of the luminaire. Time delay approx. 1 to 3 minutes.
A manual darkening of the sensor will therefore not result in an immediate
response.
Once commissioned successfully, you can choose between three operating modes
and one manual control mode.
Operating modes:
- PIR motion and light sensor
- PIR motion sensor only
- Light sensor only
Manual switching:
Sensor deactivation and manual control of the luminaire (on/off)
Range / Detection area
The specifications for the range and detection area of the PIR motion sensor
are reference values. Detection range is 120° to 150° at a depth of 5 m up to
max. 12 m, depending on motion direction (see illustration).
Too minor temperature difference between the moving object and the ambient
temperature can influence the detection range.
Local conditions and external heat sources may affect both the range and the
detection area.
Reducing the detection range
Use the decals provided to reduce the vertical detection area of the sensor.
The smaller decals reduce the detection area by around one third, the larger
ones by around one half (see sketch). Clean the sensor with a soft cloth
soaked in alcohol before applying the decals. Ensure exact positioning when
attaching the decals.
Reset to factory settings
The luminaire must be switched off five times within 30 seconds for at least 2
seconds each time to manually reset it to factory settings (see sketch).
The luminaire can furthermore be reset to the factory settings via the BEGA
Tool app.
The reset is confirmed with five flashes of the luminaire.
The smartphone will be disconnected.
Status display
Status LED lights up green:
The status LED lights up green if the motion sensor registers movement in test
mode. When the power supply returns, the status LED flashes green 3 times.
Status LED lights up blue:
The status LED lights up blue if a direct Bluetooth connection to the sensor
module was established. The LED will no longer light up if the Bluetooth
connection is interrupted or test mode is activated.
Test mode
Test mode allows the user to test the motion sensor and simplifies sensor
configuration in daylight. The test mode can be activated via the App BEGA
Tool.
In test mode, the status LED will light up green, once movement is detected in
the detection range.
The LED will no longer light up when no further movement is detected.
Test mode is ended automatically when the relevant in-app configuration screen
is exited or the Bluetooth connection is interrupted. Please note:
Motion detection in test mode depends on the set motion sensitivity.
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Accessories
70 894 Anchorage unit
Anchorage unit with mounting flange made of galvanised steel. Total length 400
mm. 3 stainless steel fixing screws M 6.
Pitch circle ø 70 mm.
See the separate instructions for use.
Spares
- Mounting plate 22 002 932 L
- PIR Light sensor graphite 75 003 952
- PIR Light sensor silver 75 003 953
BEGA Gantenbrink-Leuchten KG · Postfach 31 60 · 58689 Menden · info@bega.com · www.bega.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>