HAWKLEY NTA01A103-1A Tacoma Front Bumper User Manual
- June 1, 2024
- Hawkley
Table of Contents
HAWKLEY NTA01A103-1A Tacoma Front Bumper
Specifications :
- Model: NTA01A103-1A
- Material: Q235A
- Product Dimensions: 46.4 x 12.68 x 8.6 inches
- Package Dimensions: 50 x 13.77 x 11.8 inches
- Product Weight: 66.1 lbs
Product Usage Instructions
Required Tools:
- Ratchet
- Wrench
- Safety Glasses
- Flathead Screwdriver
- Ruler
- Angle Grinder
- Side Cutter
- Needle-Nose Pliers
- Panel Remover
- Power Cutting Tool
- Painter’s Tape
- Marker
- Tape Measure
Parts Information:
| NO. | Parts Name | Size | Qty | Color |
|---|
Installation Instructions:
-
Step 1: Unboxing and Parts Check
Open the carton, check the components, and ensure all parts are present. -
Step 2: Preparation
Remove the original bumper and gather necessary tools for installation.
Frequently Asked Questions (FAQ):
-
Q: Do I need any specialized tools to install the front bumper?
A: Yes, you will need a ratchet, wrench, safety glasses, flathead screwdriver, and other tools listed in the required tools section of the manual. -
Q: Can I skip the step involving removing the air dam if my car does not have one?
A: Yes, if your car does not have an air dam, you can skip that step during the installation process.
FRONT BUMPER
User Manual
2016-2023 Toyota Tacoma
| Model: | NTA01A103-1A |
|---|---|
| Material: | Q235A |
| Product Dimensions: | 46.4 x 12.68 x 8.6 inch |
| Package Dimensions: | 50 x 13.77 x 11.8 inch |
| Product Weight: | 66.1 lbs |
Thank you for purchasing the FRONT BUMPER. Please read this manual carefully and keep it properly if you need to refer to it afterward. If you need any support or assistance, please contact us with your product model number and order number, and our support team will help you solve problems.
WARNING
This product is designed primarily to enhance the appearance of the vehicle.
Do not rely in any way on the components of this product to protect against
injury or death in the event of an accident. To reduce the risk of serious
injury or property damage, please read all safety messages and understand all
instructions and procedure notices before attempting to install or use this
product.
CAUTION
Properly torque and recheck fasteners and security of step tread after 250
miles and inspect frequently. Do not use if damaged.
Parts Information
Note: spare parts such as N19、W27、W25、B27、B20、W16 and W43 are
provided with 1PCS each (included in the number of parts details).
Installation Instructions
-
Step 1: Open the carton and take out the parts. Check whether the number of components is complete.
-
Step 2: Remove the original bumper and prepare the parts needed to install the bumper.
-
Step 3: Take off the air dam.
Note：If the car does not have air dam, this step can be ignored .
-
Tighten out the screws inside each wheel.
NOTE: Turned the tire out to give yourself some space.
-
Tighten out the screws under neither the front of this plastic chin.
-
Step 4: Remove the original bumper.
Grab this front plastic trim part underneath and it since not reusing it anyways.
-
Step 5: Cut out the trim piece.
-
Make a mark and cut out the trim piece.
-
Remove this plastic piece on our crash bar.
Tips: It’s just held in by a couple of clips so you just have to depress, and discarded it.
-
sanding it and clean up some of these edges.
-
Step 6: Install the ⑦U-rubber strip.
-
Step 7: Remove the aluminum crash.
-
Tighten out the 6pcs bolts.
-
Tighten out 1pcs bolt on each underside.
-
Move out the aluminum crash.
-
Step 8: Remove the aluminum crash bar mounting brackets.
-
Step 9: Remove the two frame end caps and one tow hook.
-
Step 10: Remove the skip plate.
-
Step 11: Cut the little plastic pieces off.
-
Step 12: Remove 2pcs 12mm bolts on this power steering cooler, 1pcs bolt around the corner on the top of the frame.
-
Step 13: Remove 2pcs 14mm bolts on each side, let the sway bar move down. .
-
Step 14: Install our 2pcs relocation plates that move the cooler toward the inside.
-
Step 15: Remove the upper grille.
-
Open the hood. Tighten out the 2pcs bolts as shown.
-
Take off the 2pcs clips on wither side of the grille.
-
There is a wiring harness connected to the body from the grille here. Disconnect the plug of the wiring harness. Remove these 2pcs clips so you can pull it away from the grille and disconnect it up the plug.
Note：If the car does not have wiring harness(Model for TRD), this step can be ignored.
Tips: There’s a little bit easier to pinch
the clip with pair of needle nose and push down.
-
Step 16: Mounting the New Bumper.
-
Mounting the light bar ②bracket L/R.
FRONT BUMPER SIDE WINGS
User Manual
2016-2023 Toyota Tacoma
| Model: | NTA01A103-2A |
|---|---|
| Material: | Q235A |
| Product Dimensions: | 15.4 x 18.5 x 8.3 inch |
| Package Dimensions: | 27.2 x 11.4 x 9.5 inch |
| Product Weight: | 12.3 lbs |
Thank you for purchasing the FRONT BUMPER Side Wings. Please read this manual carefully and keep it properly if you need to refer to it afterward. If you need any support or assistance, please contact us with your product model number and order number, and our support team will help you solve problems.
WARNING
This product is designed primarily to enhance the appearance of the vehicle.
Do not rely in any way on the components of this product to protect against
injury or death in the event of an accident. To reduce the risk of serious
injury or property damage, please read all safety messages and understand all
instructions and procedure notices before attempting to install or use this
product.
CAUTION
Properly torque and recheck fasteners and security of step tread after 250
miles and inspect frequently. Do not use if damaged.
Parts Information
Note:
Spare parts such as B20、N22、W16 and W43 are provided with 1PCS each (included
in the number of parts details).
Installation Instructions
Note: This installation manual takes one of the models as an example.
- Step 1: Open the carton and take out the parts. Check whether the number of components is complete.
- Step 2: Removing stock bumper and cutting the bumper.
- Step 3: Install the side wings to the main body with the supplied bolts, adjust left and right to align the installation, continue trimming if the cutting point needs to be adjusted, and finally fasten the side wings.
- Step 4: Trimming fender liner and install the Support.
FRONT BUMPER Bull Bar
User Manual
2016-2023 Toyota Tacoma
| Model: | NTA01A103-3A |
|---|---|
| Material: | Q235A |
| Product Dimensions: | 32.2 x 3.7 x 5.7 inch |
| Package Dimensions: | 35.4 x 4.3 x 9.4 inch |
| Product Weight: | 3.1 lbs |
Thank you for purchasing the FRONT BUMPER Bull Bar. Please read this manual carefully and keep it properly if you need to refer to it afterward. If you need any support or assistance, please contact us with your product model number and order number, and our support team will help you solve problems.
WARNING
This product is designed primarily to enhance the appearance of the vehicle.
Do not rely in any way on the components of this product to protect against
injury or death in the event of an accident. To reduce the risk of serious
injury or property damage, please read all safety messages and understand all
instructions and procedure notices before attempting to install or use this
product.
CAUTION
Properly torque and recheck fasteners and security of step tread after 250
miles and inspect frequently. Do not use if damaged.
Parts Information
Note:
Spare parts such as B20、W16、W19 and N22 are provided with 1PCS each (included
in the number of parts details).
Installation Instructions
- Step 1: Open the carton and take out the parts. Check whether the number of components is complete.
- Step 2: Install the Bull Bar.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>