Hawkley NJK01H101C-BX Front and Rear Fender Flares Instruction Manual
- June 17, 2024
- Hawkley
Table of Contents
FENDER FLARES
(FRONT + REAR)
User Manual
2007-2018 Jeep Wrangler JK
NJK01H101C-BX Front and Rear Fender Flares
Model: | NJK01H101C-BX |
---|---|
Material: | Q235A |
Product Dimensions: | Front 43.9921.576.43 inch |
Rear 46.4918.235.61 inch
Package Dimensions:| 48.8 x 27.5 x 11.8 inch
Product Weight:| 59.5 lbs
※Thank you for purchasing the FENDER FLARES (FRONT +REAR). Please read this
manual carefully and keep it properly if you need to refer to it afterward. If
you need any support or assistance, please contact us with your product model
number and order number, and our support team will help you solve problems.
WARNING
※ This product is designed primarily to enhance the appearance of the vehicle.
Do not rely in any way on the components of this product to protect against
injury or death in the event of an accident. To reduce the risk of serious
injury or property damage, please read all safety messages and understand all
instructions and procedure notices before attempting to install or use this
product.
CAUTION
※ Properly torque and recheck fasteners and security of step tread after 250
miles and inspect frequently. Do not use if damaged.
Parts Information
NO. | Parts Name | Size | Line Graph | Qty | Color |
---|---|---|---|---|---|
/ | Left&Right Front | ||||
Fender Flares | / | 1 | Black | ||
/ | Left&Right Rear | ||||
Fender Flares | / | 1 | Black | ||
/ | Wire sets | / | 2 | Black | |
/ | H-Rubber Strip | 61cm | 1 | Black | |
MO1 | Ribbon | / | 10 | Black | |
B15 | Half Head Allen Bolts | M8x20 | 23 | Dacro Black | |
W16 | Spring Washer | 8 | 23 | Dacro Black | |
N14 | Hex Flange Nuts | M8 | 23 | Dacro Black | |
W19 | Flat Washer | 08x24x2 | 23 | Dacro Black | |
RO1 | Rivet Nuts | M6 | 15 | Color zinc plating | |
B07 | Half Head Allen Bolts | M6x20 | 15 | Dacro Black | |
W11 | Flat Washer | (1)6x12x1.5 | 15 | Dacro Black | |
W09 | Spring Washer | 6 | 15 | Dacro Black |
※ Note :
Spare parts such as B15、W16、N14、W19、R01、B07、W11、W09 are provided with 1PCS
each (included in the number of parts details).
REQUIRED TOOLS
Rivet Nuts Tool | lineman Pliers | Wrench | Allen Wrench | Panel Remover | Knife |
---|
Installation Instructions
FRONT FENDER FLARES
Step 1: Open the carton and take out the parts. Check whether the number of
components is complete.
Step 2: Remove the original rear fender flares and original rear fender
liner and prepare the parts needed to install the rear fender liner. Step 3:
Install the H-Rubber Strip. Step 4: Install the front fender flares
and tighten the bolts. Step 5: Connect the front fender flares light
wiring. Step 6: Installation of a front fender flares is
complete. Please do periodic inspections of the fender flares to make sure
that all hardware is secure and tight.
Step 7: Install all the original vehicle parts.
REAR FENDER FLARES
Step 1: Open the carton and take out the parts. Check whether the number of
components is complete.
Step 2: Remove the original rear fender flares and original rear fender
liner and prepare the parts needed to install the rear fender liner. Step 3:
Install the H-Rubber Strip. Step 4: Install the rear fender flares and
tighten the bolts. Step 5: Installation of a rear fender flares is
complete. Please do periodic inspections of the fender flares to make sure
that all hardware is secure and tight.
Step 6: Install all the original vehicle parts.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>