MEEC TOOLS 015275 1300W Garden Pump Instruction Manual

MEEC TOOLS 015275 1300W Garden Pump

EU DECLARATION OF CONFORMITY
Item number 015275

Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the manufacturer.
GARDEN PUMP
230V, 1300W, 4800l/h
Conforms to the following directives, regulations and standards:

62233:2018
EMC 2014/30/EU| EN 55014-1:2017+A11, EN 55014-2:2015, EN IEC 61000-3-2:2019, EN 61000-3-3:2013+A1
RoHS 2011/65/EU + 2015/863| EN 50581:2012

This product was CE marked in year:

Skara 2021-03-31

Mattias Lif
BUSINESS AREA MANAGER (Signatory for Jula and authorised to compile the technical documentation.

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision.
• Familiarise yourself with the controls on the product and how to use them. Read all the instructions and safety instructions before use. Failure to follow all the instructions and safety instructions can result in a risk of electric shock, serious personal injury and/or material damage.
• Contact the retailer or qualified personnel if you have any problems or questions.
• Store these instructions so that they are readily available for everyone who uses the product. These instructions should be enclosed with the product if it is sold or passed on.
• Do not make any modifications to the product. Only use accessories recommended by the manufacturer.
• The product must only be used for its intended purpose and in accordance with these instructions. The product must only be used for its intended purpose and in accordance with these instructions, otherwise there is a risk of personal injury and/or material damage. The manufacturer cannot accept liability for personal injury and/or material damage resulting from improper use.
• A damaged power cord or plug must be replaced by an authorised service centre, or other qualified personnel, to ensure safe use.
• Do not use the product if it is damaged. Always check the power cord, plug and casing before use. If the product is damaged, or not working properly, it must be repaired or discarded.
• Pull out the plug immediately if the power cord or product gets damaged or stops working properly, otherwise there is a risk of electric shock.
• Repairs must be carried out by qualified personnel. Imperfect repairs can result in a risk of electric shock, serious personal injury and/or material damage.
• Do not pull the power cord to pull out the plug.
• Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces. Avoid kinking or bending the power cord.
• If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the product.
• If the product is used outdoors, only use an extension cord approved for outdoor use.
• The product is not intended to transport water for human consumption.
• Do not use the product to transport corrosive, flammable or explosive substances such as petrol or other petroleum products, nitrogenous liquids, grease, oil, salt water or waste water from toilets, or liquid that has a higher viscosity than water.
• The temperature of the pumped water must not exceed 35°C.
• Keep this product out of the reach of children.
• Do not use the product if there are any persons in the water.
• Make sure the product does not suck up aquatic animals, such as fish.
• Pay attention to the risk of contaminating the liquid as a result of leaking lubricant.
• Protect electrical connections from moisture.
• Do not expose the product to temperatures below 0°C. Make sure that the product is not run without water.
• Do not pump aggressive liquids or abrasive material.
• Do not pull the power cord or float switch cord to move the product, and do not use them to secure the product from moving.
• The product is only intended for household use and is not suitable for commercial purposes.
• The manufacturer cannot accept liability for personal injury or material damage resulting from improper use.

IMPORTANT:
The product must be connected to the mains with a residual current device of max 30 mA.

SYMBOLS

TECHNICAL DATA

• Rated voltage: 230 V ~ 50 Hz
• Nominal input power: 1300 W
• Pump pressure: 5 bar
• Flow, Qmax: 80 l/min
• Delivery height, Hmax: 50 m
• Suction height: max 8 m
• Water temperature: max 35°C
• Ambient temperature: 0 – 40°C
• Protection rating: IPX4
• Cord length: 1 m
• Connection; 1″ (R25)
• Size: L44 x W22 x H32 cm
• Weight: 11 Kg

DESCRIPTION

Fully automatic garden pump with LCD screen. With aluminium motor that supplies a flow of up to 80 l/min and maximum delivery height of 50 metres. You can set the water pressure and when to run the pump via the LCD screen. It is also possible to monitor the flow of water in and out. The pump’s transport-friendly design and handle make it easy to move around.

1. Draining
2. Inlet
3. Filter
4. Filling with water and bleeding
5. Outlet
6. LCD display

USE

INTENDED USE

This product is intended for permanent installation for pumping water from non-pressurised sources of water (for example wells) for domestic and garden purposes in private households. Fresh water or rainwater and chlorinated water (pools) can be pumped with the product. The product must only be used as it is intended to be used and in accordance with the technical data and other instructions in these instructions.

Incorrect/non-intended use

Continuous operation, pumping of drinking water, salt water, food, contaminated water or water containing sand or abrasive particles, corrosive liquids and chemicals, flammable or explosive liquids, volatile/gaseous liquids and liquids hotter than 35°C.

ELECTRICAL CONNECTION

The product must be connected to a correctly earthed power point protected with a residual current device that has a maximum tripping current of 30 mA.

IMPORTANT:
The inlet tube must be filled with water before starting the product.

Stopping

1. Press the OK button. Press the power switch OK again to switch off the product when “Pump off” is shown.
2. Pull out the plug.
3. Open the tap to relieve the pressure in the outlet tube.

INSTALLATION AND COMMISSIONING

1. Remove the product from the packaging and place it on a level, stable surface. The installation should be protected from rain and splashing water.
   FIG. 2

2. Connect the suction hose to the water inlet and the outlet hose to the water outlet. Seal the connection with Teflon tape, if necessary.
   FIG. 3
   IMPORTANT:

   • The suction tube should be provided with a non-return valve to prevent return flow, which can cause the water in the product and the suction tube to empty when the product is not running. Any leakage will allow air to penetrate the system, which reduces the pumping capacity.
   • The suction tube should be provided with a pre-filter if the pumped water is contaminated or turbid, to avoid damaging the non-return valve and product.
   • The suction tube should consist of a reinforced hose with a 3/4” threaded connection that is not squeezed by the intake pressure.
   • The suction tube should have an uninterrupted inclination from the pump to the source of the water. No part of the suction tube should be higher than the pump, this can result in pockets of air.
   • Make sure that the inlet on the suction tube is always covered with water. Suction and outlet tubes should be installed so that the product is not subjected to mechanical stress.

3. Open the refill opening cap and fill with water until it runs over. Replace the cap.
   FIG. 4
   IMPORTANT:

   • The outlet tube must withstand the maximum pressure of the product. Use a 1/2” outlet tube with a suitable screw coupling.

   • The product has an optimal pump capacity at a lifting height of up to
     1 metre. Leaks on the pressure side can result in interference and malfunction. A pressure tank or similar pressure equalisation buffer should therefore be installed on the pump outlet.

   • In order to reduce the number of times the pump starts. To simplify emptying the system a shut-off valve should be installed between the product and the outlet tube, to prevent the water in the pressure tube running out.

   • Even minor leakage can lead to malfunction.

4. Drain the water from the product by opening the drain on the pump.
   FIG. 5

5. Open the transparent cover, take out the filter and clean it.
   FIG. 6
   EXPLANATION OF DISPLAY

   • To fill the pump with water (vent) open the refill plug and pour water in until the inlet tube and pump housing are full of water. If despite filling the level of water does not reach the refill opening then the non-return valve is probably defective and must be replaced. Open all the taps, valves etc. when filling with water so that the air in the tubes can flow out.
     NOTE:
     Do not run the product without water other than temporarily – dry running reduces the life span. Damage resulting from running dry is not covered by the warranty.

6. Replace the cap over the refill opening when the pump housing is full of water and firmly tighten.

7. Plug the plug into an earthed power point.

8. Make sure that all the valves in the intake and pressure tube are open –the pump must not run with closed valves.

9. Start the product with the power switch. Switch off the product after use with the power switch.

MAINTENANCE

WARNING!

• Electrical safety! Pull out the plug before working on the product.
• Risk of personal injury. Make sure that the product and all connected devices are pressureless before working on the product.

CLEANING

• The pump must be flushed with fresh water if chlorinated water or water containing sedimented contaminants is pumped.
• To remove clogging or blockage, remove the suction tube from the pump inlet, connect the water hose to the pump inlet, and run the product until the blockage is removed. Reconnect the suction tube afterwards and test.
• Keep the ventilation openings on the motor clean and make sure they are not blocked.

DISMANTLING AND STORAGE

1. Switch off the product and pull out the plug.
2. Open the tap on the outlet tube and wait until all the water has run out.
3. Empty the product by unscrewing the drain plug underneath the pump.
4. Disconnect the suction tube and pressure tube from the product.
5. Store the product frost-free (at least 5°C).
   IMPORTANT:
   Risk of material damage. All the seals should be replaced if the product is dismantled.
   

Frost

Take the following measures if there is a risk of frost. Undo the drain screw under the pump outlet and allow all the water to run out from the pump. If very low temperatures are expected the pump should be disconnected, emptied and then stored in a dry and frost-free place.
IMPORTANT:
Risk of material damage. The product and its accessories contain water, which means that they can burst if the water freezes.

SERVICE AND REPAIRS

The product must only be serviced by qualified personnel using identical spare parts. This will ensure that the product remains safe to use.

TROUBLESHOOTING

The troubleshooting guide on the next page is used to identify the causes of common problems and how they can be rectified. Contact the retailer if the problem cannot be rectified with the help of the troubleshooting guide. The warranty does not cover damage resulting from repairs or attempted repairs carried out by unauthorized persons.

WARNING!
Risk of personal injury. Repairs that are not carried out correctly can result in the risk of fatal or serious personal injury and/or material damage.

TROUBLESHOOTING CHART

The LCD display is blank.

| ****

No power supply.

| Check the power cord, plug, power point and fuse. Reconnect the power supply.
Electrical fault on the product.| Contact a qualified service technician.
Standby is shown on the LCD display.| The pressure in the outlet tube is higher than the product’s start pressure.| Open the tap to lower the pressure in the outlet tube until the product starts.
Standby is shown on the LCD display all the time.| The delivery height is too high for the set start pressure.| Adjust the start pressure from the control panel.

Power on is shown on the LCD display.

| ****

The product is in standby mode.

| Press the OK button and then press the OK button again when the prompt is shown. The product returns to run mode.

No water inlet is shown on the LCD display.

| ****

The product has been switched off automatically by the run dry protection after 30 seconds without water.

| Check if there is an air leak in the suction tube and if the outlet valve is open. ‘Fill the pump and inlet tube with water and press the OK button. Press the OK button again to start the product.

No water inlet is shown on the LCD display.

Leakage warning is shown on the LCD display.

| The product has switched off automatically after it has been started and stopped too many times as a result of leaking in the outlet tube.| ****

Check and seal the outlet tube and its connections.

The product has started and stopped many times as a result of a blockage or leakage caused by a defective non-return valve.| Check the non-return valve. Fit a non- return valve on the suction tube, if necessary. It is strongly recommended to fit a filter on the suction tube.

The product does not start when the power is switched on.

| ****

The mechanical seal has fastened.

| The mechanical seal can fasten if the product has not been used for some time. Switch off the product, pull out the plug, and wait until the product has cooled. Turn the axle with a screwdriver in the slot on the end to release the seal. The pump can then be started.

Insufficient flow or not enough water filled.

| Contaminated water has caused clogging, which reduces the pump capacity of the product.| Clean the filter and replace any damaged or worn parts (for example impeller).
---|---|---
Hose/pipe/filter is blocked.| Clean the hose/pipe/filter.
Hose/pipe damaged.| Replace the tube.
The suction tube has been squeezed together by the suction pressure.| Replace the hose or tube with a more suitable type.
Air in the product, which has not been correctly filled with water.| ****

Fill the product full of water.

The inlet opening should be at least 10 cm below the surface of the water.| Check that the depth of the water is sufficient, the inlet opening should be at least 10 cm below the surface of the water.
The suction tube or its connection is not tight.| Replace or seal the suction tube and its connection.

The product starts, but soon stops.

| The product or tube is blocked.| Clear the product and/or tube.
The overheating protection has switched off the product because the ambient temperature or temperature of the water is too hot.| ****

The maximum temperature of the water/air is 35°C. The product can be started again when it has cooled.

The impeller is damaged.| Contact a qualified service technician.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>