HOOKE ROAD BXG.9803-S 4 Runner Rear Trunk Cargo Rack Plus Window Molle Panel Kit Installation Guide

HOOKE ROAD BXG.9803-S 4 Runner Rear Trunk Cargo Rack Plus Window Molle

Panel Kit

WHAT IN THE BOX

PARTS

Tools required

• Drive Socket Ratchet Wrench;
• 4mm, 5mm Hex Bit Socket;
• 10mm, 13mm Wrench;
• 10mm, 13mm Shallow Socket;

Installation time

About 1.5 hours, 1-2 people may be needed. Installation time may differ according to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!) To view the electronic version (BXG.9803-S), please scan the QR code.

Installation instruction

Step 1 : Firstly, it is recommended to fold down the rear seats. You may need to remove the relevant accessories from the original vehicle. Please refer to the diagram below for the locations to disassemble. Subsequent steps will be demonstrated using the driver’s side as an example.

Step 2: Tear open the provided EVA foam strips and adhere it to the contact surfaces of the following brackets: the bottom bracket, the middle assembly part, and the upper brackets.

Step 3: Next, you should assemble the molle panel and three brackets (bottom bracket & upper bracket & cargo rack connectors). Please refer to the diagram below for installation. You will need M616 screws and M820 screws for this assembly.

• Button Head Socket Cap Bolts Screws (M616) 4 & (M820) 3
• Split Lock Washer (D6) 4 & (D8) 3
• Flat Washer (M6)4 & (M8) 3
• Flange Hex Lock Nuts (M6) & (M8) *3
• Step 4: Next, lift the assembled molle panel onto the driver’s side of the vehicle, preparing to install it on the car.
• Step 5: Next, install the molle panel on the car. When installing the bottom bracket, place 40mm-long nylon spacers and secure them with M655 screws. Use the original car screws for the bottom holes. For the remaining hole, insert a 50mm-long nylon spacer and secure it with an M670 screw.
• Step 6: Following that, the installation of the molle panel on the driver’s side is complete. Please use the same method to install it on the passenger’s side.
• Step 7: Next, assemble the cargo rack (1) (no logo) and the middle assembly part using M8*20 screws and nuts.
• (3) Button Head Socket Cap Bolts Screws (M8*20
• (3) Flat Washer (M8)
• (3) Flange Hex Lock Nuts (M8)
• Step 8: Next, place the cargo racks (1) and (2) inside the vehicle, preparing to assemble them on the car. Make sure to place the one assembled in the previous step on the left side.
• Step 9: Next, assemble cargo racks (1) and (2) by connecting them with the middle assembly part. Secure the remaining three holes in place.
  • (3) Button Head Socket Cap Bolts Screws (M8*20)
  • (3) Flat Washer (M8)
  • (3) Flange Hex Lock Nuts (M8)
• Step 10: Next, place the reinforcement plate on the inside of the cargo rack’s connection point. Secure it with M8*20 screws and nuts, but do not tighten the screws for now.
  • (4) Button Head Socket Cap Bolts Screws (M8*20)
  • (4) Flat Washer (M8)
  • (4) Flange Hex Lock Nuts (M8)
• Step 11: Next, connect cargo racks (1) and (2) with the molle panel, and secure them in place using M8*20 screws and nuts.
  • (3) Button Head Socket Cap Bolts Screws (M8*20)
  • (3) Flat Washer (M8)
  • (3) Flange Hex Lock Nuts (M8)
• Step 12: Finally, it is recommended to have two people for this operation. Lift the cargo rack to a horizontal position first and then tighten the screws in the middle section.
• Step 13: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention

1. The product parts in this instruction may differ slightly from the actual product contents but generally do not affect the installation of the product.
2. Please feel free to contact your distributor if you have any kind of questions about your purchase.

Google Hooke Road to find your parts. Feel Free To Share Your Vehicle @HookeRoad4x4 With The Hashtag #hookeroad If You’d Like

Specifications

• Model: BXG.9803-S
• Contents:
  • 2 x M6*70 Button Head Socket Cap Bolts Screws
  • 2 x M6*55 Button Head Socket Cap Bolts Screws
  • 8 x M6*16 Button Head Socket Cap Bolts Screws
  • 22 x M8*20 Button Head Socket Cap Bolts Screws
  • 12 x Split Lock Washer D6
  • 12 x Split Lock Washer D8
  • 12 x Flat Washer M6
  • 22 x Flat Washer M8*16
  • 8 x Flange Hex Lock Nuts M6
  • 16 x Flange Hex Lock Nuts M8
  • 2 x Nylon Round Spacer 8.21440
  • 2 x Nylon Round Spacer 8.21450
  • 2 x EVA Foam Strips
  • 4 x EVA Foam Strips
  • 1 x Net
• Tools Required:
  • Drive Socket Ratchet Wrench
  • 4mm, 5mm Hex Bit Socket
  • 10mm, 13mm Wrench
  • 10mm, 13mm Shallow Socket
• Installation Time: About 1.5 hours, 1-2 people may be needed.

Frequently Asked Questions (FAQ)

Q: How do I ensure all parts are present before starting installation?
A: You can refer to the contents list provided in the manual and verify each part against the list.

Q: Can one person install the cargo rack?
A: While one person can install the cargo rack, having an extra person may ease the process due to the size and weight of the components.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>