BEGA 24910 Wall Luminaire Applique Instruction Manual
- June 1, 2024
- BEGA
Table of Contents
BEGA 24910 Wall Light Fixture
Specifications:
- Material: Aluminum alloy and thick-walled crystal glass
- Control Options: Switched phase (on/off), continuous phase via BEGA Smart app or wi butler pro with Wibutler app
- Color Temperature: 3000K and 4000K
- Brightness Adjustment: Yes
- Default Settings: 3000K, maximum brightness
- Connected Module Wattage : 5.7 W
- Connected luminaire Wattage: 6.8 W
- Color Rendering Index (CRI): >80
- Service Life: 50,000 hours
Instructions for use
Application
Wall luminaire made of aluminium alloy and thick-walled crystal glass. The
luminaire can be controlled via a switched phase classically on/off or with a
continuous phase either via the BEGA Smart app or in combination with the
wibutler pro (2. Gen.) with the wi butler app. The colour temperature can be
set optionally to 3000 K and 4000 K, and the luminaire brightness can be
adjusted. The default factory settings are 3000 K and maximum brightness.
Product Description
- Luminaire made of aluminium alloy, aluminium and stainless steel
- BEGA Unidure® coating technology
- Crystal glass, white inside
- Silicone gasket
- 2 mounting holes ø 6 mm
- Distance apart 210 mm
- 2 cable entries for through-wiring of mains supply cable ø 7-10.5 mm
- Connection terminal 2.5@
- Earth conductor connection
- Data matrix code for convenient configuration via smartphone or tablet
- Radio frequency 2.4 GHz
- Maximum output +6 dBm Zigbee 3.0 and Bluetooth 5.0
- Complies with flicker requirements in accordance with IEEE 1789,
- DIN IEC/TR 63158, DIN IEC/TR 61547-1
- LED power supply unit
- 220-240 V x 0/50-60 Hz
- DC 176-280 V
- Safety class I
- Protection class IP 65
- Dust-tight and protection against water jets
c – Conformity mark
This product contains light sources of energy efficiency class(es) C
Product Usage Instructions:
Installation:
Installation and commissioning must be done by a qualified electrician
following national safety regulations.
Control:
The luminaire can be controlled via a switched phase for on/off
functionality. For advanced control options, use the BEGA Smart app or
wibutler pro with the wibutler app to adjust color temperature and brightness.
Color Temperature and Brightness Adjustment:
You can set the color temperature to either 3000 K or 4000 K according to
your preference. The brightness of the luminaire is adjustable to suit
different lighting needs.
EU Declaration of Conformity
BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 24 910
complies with Directive 2014/53/EU (RED). The complete text of the EU
Declaration of
Conformity is available at the following Internet address:
https://www.bega.com/conf/de/24910
Safety
The installation and operation of this luminaire are subject to national
safety regulations. Installation and commissioning may only be carried out by
a qualified electrician. The manufacturer accepts no liability for damage
caused by improper use or installation. If subsequent modifications are made
to the luminaire, the person responsible for these modifications shall be
considered the manufacturer.
Maintenance:
Ensure the electronic components are protected against overvoltage.
Consider using bounce-free switching contacts like an electronic relay for
optimal protection.
Overvoltage protection
The electronic components installed in the luminaire are protected against
overvoltage in accordance with DIN EN 61547. To achieve an additional
protection against e. g. transients, etc. we recommend separate overvoltage
protection components. You can find them on our website at www.bega.com.
The ideal protection of all electronic components
installed in the luminaires is achieved by using bounce-free switching
contacts such as an electronic relay (solid-state relay), e.g. BEGA 71 320.
Range
The Zigbee radio range between individual devices is usually 30 m, with
ambient conditions playing a decisive role. Bluetooth generally has a range of
12 m, whereby environmental conditions and the end device used (e.g.
smartphone) play a decisive role.
IMPORTANT:
The enclosed data matrix-code labels are required for the initial setup of the
luminaires. Please save these labels with the assigned specifications for the
installation site (room description, location, etc.) with your documentation
(e.g. instructions for use top of Page 1).
Lamp
Module connected wattage 5.7 W
Luminaire connected wattage 6.8 W
Module designation LED-1634/83040
Colour rendering index CRI > 80
Rated temperature: ta = 25 °C
Service life criteria: 50 000 h / L70
Operation at colour temperature 3000 K
Module luminous flux 1045 lm
Luminaire luminous flux 507 lm
Luminaire luminous efficiency 74,6 lm / W
Operation at colour temperature 4000 K
Module luminous flux 1100 lm
Luminaire luminous flux 533 lm
Luminaire luminous efficiency 78,4 lm / W
Installation
LEDs are high-quality electronic components! Please avoid touching the light
output opening of the LED directly during installation or relamping. Undo the
screws and lift off the luminaire top.Lead the mains supply cable through the
cable entry of the luminaire base. Fix the luminaire base with enclosed or any
other suitable fixing material onto the mounting surface. Be sure to use the
gasket rings supplied. Make an earth conductor connection. Push silicone
sleeves over the lines and make electrical connection. In order to guarantee
the maximum service life of the electrical components, the enclosed desiccant
pouch must be placed in the luminaire. Remove the desiccant pouch from the
foil packaging and place it in the position marked by the red information
label immediately before finally closing the luminaire. Make an earth
conductor connection between the luminaire top and the luminaire base. Make
sure that the gasket is positioned correctly. Install the luminaire top, press
on and tighten screws evenly.
Initial setup
For successful configuration, the luminaires should start in their factory
settings. If the installation is not carried out correctly, or access via the
BEGA Smart or wibutler apps is no longer possible, the luminaire should be
reset to factory settings.
Reset to factory settings
The luminaire must be switched off five times (for at least 3 seconds each
time) to manually reset it to factory settings (see sketch). The luminaire can
also be reset to the factory settings via the BEGA Smart or wibutler
apps.
Download app
Control using a switched phase
When the luminaire is to be activated and deactivated with classic on/off
controls via a switched phase, the colour temperature and brightness can be
set permanently in the BEGA Smart app under “Configure start-up behaviour”
once the luminaire is switched on. The app can find the luminaire for 30
minutes after switch-on, provided it is within the immediate vicinity of the
smartphone.
Integration into a BEGA Smart system
When integrating the luminaire into a BEGA Smart system (required for variable
adjustment of colour temperature and brightness, integration into groups,
scenarios, automation etc.), it must be connected to a continuous phase
(Pstandby = 0.25 W). In the BEGA Smart app, either select “Create new system”
or add a new device to your existing system. Then select “Smart luminaires”
and follow the instructions.
Integration into a wibutler system
When integrating the luminaire into a wibutler system), it must be connected
to a continuous phase (Pstandby = 0.25 W). A wibutler system enables
combinations with products from other manufacturers and systems, integration
into voice assistants as well as remote access. One configured wibutler per
parent system is required along with the wibutler app.
Then select “Add devices” in the app under “Manufacturer: BEGA” and follow the instructions.
For more information go to : www.wibutler.com
Cleaning · Maintenance
Clean luminaire regularly with solvent-free cleansers from dirt and deposits.
Do not use high pressure cleaners.
Replacing the LED module
The designation of the LED module is noted on a separate label in the
luminaire or on the underside of the specific LED module. The light colour and
light output of BEGA replacement modules correspond to those of the modules
originally fitted. The module can be replaced by qualified persons using
standard tools. Disconnect the system and open the luminaire. Please follow
the installation instructions for the LED module. Inspect and, if necessary,
replace the luminaire gaskets. Defective glass must be replaced. Close the
luminaire.
Accessory
71 895 wibutler pro (2. Gen.) Using wibutler pro, BEGA Smart components can
easily be integrated into a Professional Smart Home alongside third party
products using wibutler pro.
Spares
- Spare glass: 11 003 165 11
- LED power supply unit: DEV-0487/24V
- Smart Dim SW – Platine: 61 002 199
- LED module: LED-1634/83040
- Gasket: 83 001 574
FAQ:
Q: What is the recommended range for Zigbee and Bluetooth
connectivity?
A: The Zigbee radio range is typically 30 meters, while Bluetooth has a range
of about 12 meters. Environmental conditions and the type of end device used
can affect these ranges.
Q: How do I initially set up the luminaires?
A: Use the enclosed data matrix-code labels for the initial setup. Keep
these labels with the installation site specifications for future reference.
BEGA Gantenbrink-Leuchten KG
Postfach 31 60
58689 Menden
info@bega.com
www.bega.com
References
- BEGA Smart - Apps on Google Play
- BEGA Smart on the App Store
- BEGA · Das gute Licht.
- DBT Digital Building Technology | wibutler IoT-Plattform
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>