TYGER TG-LD2J63598 Lander Running Board User Guide

TYGER LANDER™
TG-LD2J63598

Parts List

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT

TORQUE VALUES

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. FACTORY INSTALLED OR AFTERMARKET SIDE STEPS OR RUNNING BOARDS MUST BE REMOVED.

STEP 1
Start installation toward the front of the Passenger/Right side of the vehicle. Locate the factory threaded mounting hole in the bottom of the floor (Fig 1).

Passenger/Right Side Installation Pictured

STEP 2
Select the Passenger/Right Front Mounting Bracket (Fig 2).
IMPORTANT: Front and Rear Mounting Brackets look very similar but are unique. The Front Mounting Bracket has a longer mounting tab than the Rear Mounting Bracket.

Passenger/Right Side Installation Pictured

STEP 3
Attach Passenger/Right Front Mounting Bracket to the threaded hole in the bottom of the floor panel with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 2). DO NOT tighten hardware at this time.
STEP 4
Select the Passenger/Right Front Support Bracket. Attach the Support Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts (Figs 3 & 4). Attach the Support Bracket to the Mounting Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut (Figs 3 & 4). DO NOT tighten hardware at this time.

Passenger/Right Side Installation Pictured

STEP 5
Move to the #2 center location, (Figure 5). Repeat STEPS 3 & 4 to attach the Center Mounting Bracket and the Center Support Bracket (Figs 5-7).
NOTE: The Center Support Bracket has a hole in the top and the Rear Support Bracket has a notch (Fig 6).

Passenger/Right Side Installation Pictured

STEP 6
Move to the rear location (Fig 8). Repeat STEPS 3 & 4 to attach the Rear Mounting Bracket and the Rear Support Bracket to the rear location (Fig 9).

Passenger/Right Side Installation Pictured

STEP 7
Select the Passenger/Right Tyger Lander. Carefully place Sidebar on the Rear Mounting Bracket.
IMPORTANT: DO NOT slide or rotate Sidebar on cradle, or damage to the finish may result. Attach the Tyger Lander to the Front and Rear Mounting Brackets with (4) 8mm Combo Bolts (Figs 10-12). DO NOT tighten hardware at this time.

Passenger/Right Side Installation Pictured

STEP 8
Next, attach the Tyger Lander to the front face of the Center Mounting Bracket with (2) 10mm Hex Bolts, (4) 10mm Flat Washers and (2) 10mm Nylon Lock Nuts (Figs 13 & 14). DO NOT tighten hardware at this time.

Passenger/Right Side Installation Pictured

STEP 9
Adjust and level the Tyger Lander and fully tighten all hardware.
STEP 10
Repeat STEPS 2-9 to attach the Driver/Left Tyger Lander.
STEP 11
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
ATTENTIONS: To protect your investment, DO NOT use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Tyger Lander.

Customer Support:www.TygerAuto.com/Contact

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>