Tyger Auto TG-RS6D60078 6 Riser Running Boards Instruction Manual

Tyger Auto TG-RS6D60078 6 Riser Running Boards

Product Information

Product Specifications

• Model: TG-RS6D60078
• Torque Values:
  • Class 8.8: 6-7 ft-lbs (6mm), 15-16 ft-lbs (8mm), 31-32 ft-lbs (10mm), 54-55 ft-lbs (12mm), 87-88 ft-lbs (14mm)
  • Class 10.9: 6-7 ft-lbs (6mm), 22-23 ft-lbs (8mm), 44-45 ft-lbs (10mm), 78-79 ft-lbs (12mm)
• Parts List:
  • Passenger/Right Rear Bracket
  • Passenger/Right Front Mounting Bracket
  • Driver/Left Front Mounting Bracket
  • Driver/Left Rear Bracket
  • Passenger/Right Center Mounting Bracket
  • Driver/Left 6inch Tyger Sidebar
  • Driver/Left Center Mounting Bracket

Product Usage Instructions

Before Installation
Read instructions carefully before starting installation. Remove contents from the box and verify all parts are present. Failure to identify damage before installation could lead to a rejection of any claim. If missing parts or any damage is found, please take a picture for the claim purpose.

Procedure

1. Remove contents from the box and verify all parts are present.
2. Read instructions carefully before starting installation.
3. Drilling may be required.

• Step 1
  Starting at the driver’s side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel.

• Step 2
  Determine the correct procedure to attach the driver-side front bracket for your model/year:

Models without factory threaded inserts in body panel:

• Select (1) 8mm Bolt/nut Plate. Partially thread an 8mm Hex Bolt onto the thread of the Nut Plate. Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole. Feed the threaded bolt on the Bolt Plate through one of the hex-shaped factory holes.
• Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel.
• Remove the 8mm Hex Bolt from the nut on the Bolt Plate. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel. Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer. DO NOT tighten the hardware.

Frequently Asked Questions (FAQ)

• How do I file a claim for missing parts or damage?
  To file your claim, please visit www.tygerauto.com/contact.

• I have a different model/year vehicle, how do I adjust the installation process?
  Refer to the specific instructions provided for models without factory- threaded inserts in the body panel and follow the steps accordingly to ensure proper installation.

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT WWW.TYGERAUTO.COM/CONTACT.

TORQUE VALUES

Fastener Size

| Class 8.8 Torque (ft-lbs)|

Class 10.9 Torque (ft-lbs)

---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126

Overview

Parts List

• x1 Driver/Left 6inch Tyger Sidebar
• x1 Passenger/Right 6inch Tyger Sidebar
• x2 Driver Front/Passenger Rear Mounting Brackets
• x2 Passenger Front/Driver Rear Mounting Brackets
• x1 Driver/Left Center Mounting Bracket
• x1 Passenger/Right Center Mounting Brackets
• x6 8mm Bolt/Nut Plate
• x12 8mm x 30mm Hex Bolts
• x12 8mm x 25mm Combo Bolts
• x12 8mm x 24mm OD x 2mm Flat Washers
• x12 8mm Lock Washers
• x6 8mm Hex Nuts
• x 68mm Plastic Retainers
• x10 6mm x 25mm Button Head Bolts
• x10 6mm x 18mm OD x 1.6mm Flat Washers
• x20 6mm Flange Nuts
• x4 16mm x 60mm Large Spacer
• x2 16mm x 34mm Small Spacer
• x1 4mm Hex Wrench

Installation

PROCEDURE:
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. DRILLING MAY BE REQUIRED.

STEP 1
Starting at the driver’s side-front of the vehicle, remove the sealing tape covering the factory holes in the side of the inner panel (Fig 1).

Driver/Left Side Installation Pictured

STEP 2
Determine the correct procedure to attach the driver-side front Bracket for your model/year:

Models without factory threaded inserts in body panel:

• Select (1) 8mm Bolt/nut Plate (Fig 2). Partially thread an 8mm Hex Bolt onto the thread of the Nut Plate (Fig 3). Thread the Hex Bolt in until it is flush with the welded nut. Use the Hex Bolt as a handle and insert the Bolt and Nut Plate into the oval hole (Fig 4). Feed the threaded bolt on the Bolt Plate through one of the hex-shaped factory holes.

• Thread (1) 8mm Plastic Retainer onto the threaded end and down tight against the body panel (Fig 5).
  NOTE: The Plastic Retainer is designed to keep the Bolt/Nut Plate from falling into the body panel and to aid in Bracket installation.

• Select (1) Driver/Left Bracket (Fig 6). Attach the Bracket to the threaded end of the Bolt Plate with (1) 8mm Flat Washer, (1) 8mm Lock washer and (1) 8mm Hex Nut (Fig 6).
  IMPORTANT: The driver/Left Front Bracket is the same as the Driver/Left Center and Passenger/Right Rear Brackets. DO NOT tighten hardware at this time .

• Remove the 8mm Hex Bolt from the nut on the Bolt Plate from STEP 2a. Rotate the Bolt on the Bolt Plate until the threaded nut lines up with the remaining hole in the Mounting Bracket and body panel, (Fig 7). Attach the Bracket to the threaded Nut Plate with (1) 8mm x 30mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 7). DO NOT tighten the hardware.

Models with factory threaded inserts:

• Attach (1) Driver/Left Mounting Bracket to the threaded inserts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washer (Figs 8 & 9). DO NOT tighten the hardware.

STEP 3
Attach the Bracket to the back of the pinch weld with (2) 6mm Button Head Bolts, (4) 6mm Flat Washers, (1) Large Spacer and (2) 6mm Flange Nuts (Fig 10). DO NOT fully tighten the hardware.

IMPORTANT:
2009-12 models not equipped with factory holes will require drilling through the pinch weld to fully attach the Bracket. DO NOT drill through pinch weld at this time (see STEP 7).

STEP 4
Move along the side of the body panel to the centre mounting location (Fig 11). Repeat STEPs 1-3 to install (1) Driver/Left Center Mounting Bracket to the center mounting location. Note that you will be using a small spacer and one set of hardware instead for the pinch weld location.

STEP 5
Move to the rear location (Fig 12). Repeat STEPs 1-3 to attach (1) Passenger/Right Rear Mounting Bracket to the Driver/Left rear mounting location.

STEP 6
Select the Driver/Left 6-inch Tyger Sidebar. Place the Running Board onto the Mounting Brackets and attach it with (6) 8mm Combo Bolts (Fig 13). DO NOT tighten the hardware.

STEP 7
Properly level and adjust the Tyger Sidebar and fully tighten all hardware.

2009-12 models requiring drilling through pinch trim:

• Level the Tyger Sidebar to the vehicle. Make sure all (3) Brackets are tight against the bottom of the body panel and tighten all mounting hardware.

• Mark the location of the slots onto the pinch weld.

• Drill (2) 1/4” holes through the pinch weld for the front and rear bracket, and (1) 1/4” holes for the centre bracket.
  IMPORTANT: DO NOT drill too close to the bottom edge of the pinch weld. Drill the holes in the centre of the marked slots.

• Repeat STEP 3 to attach the Brackets to the drilled holes in the pinch weld. Check for level then fully tighten all hardware.

STEP 8
Repeat STEPs 1-7 to attach the Passenger/Right 6-inch TYGER Running Board.

STEP 9
Do periodic inspections of the installation to make sure that all hardware is secure and tight.

Customer Support:
www.TygerAuto.com/Contact.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>