TG-SS2T35848 Tyger Rider Running Boards Installation Guide

TG-SS2T35848 Tyger Rider Running Boards

Product Information

• Specifications:
  • Product Name: Tyger Rider Running Boards
  • Material: High-quality steel
  • Finish: Black powder coating
  • Package Contents:
  • 1 Driver/Left Tyger Rider
  • 1 Passenger/Right Tyger Rider
  • 1 Driver/Left Front Mounting Bracket
  • 1 Passenger/Right Front Mounting Bracket
  • 3 Driver/Left Center and Rear Mounting Brackets
  • 3 Passenger/Right Center and Rear Mounting Brackets
  • 16 8mm x 30mm Hex Bolts
  • 16 8mm Lock Washers
  • 16 8mm x 24mm OD x 2mm Flat Washers
  • 16 8mm x 25mm Combo Bolts

Product Usage Instructions

1. Step 1: Driver/Left Side Installation
   • Remove plastic plugs or hex bolts covering the threaded holes in the floor panel.
   • Attach the Driver/Left Front Mounting Bracket to the mounting location.
2. Step 2: Driver/Left Front Mounting Bracket
   • Attach the Bracket using the provided hardware.
   • Avoid sliding the Tyger Rider on the Brackets to prevent damage.
   • Do not tighten the hardware at this stage.
3. Step 3: Driver/Left Center and Rear Mounting Bracket
   • Attach the Bracket to the 2nd mounting location as shown.
4. Step 4: Continue to the 3rd and rear mounting locations.
   • Attach the Driver/Left Center and Rear Mounting Bracket to each location.
5. Step 6: Level and adjust the Tyger Rider, then tighten all hardware.
6. Step 7: Repeat Steps 1-6 to attach the Passenger/Right Side Tyger Rider.

FAQs

• Q: What should I do if I find missing parts or damage before installation?
  • A: If missing parts or damage are found, please take a picture for claim purposes and visit www.tygerauto.com/contact to file your claim.
• Q: What are the torque values for different fastener sizes?
  • A: Refer to the following torque values for different fastener sizes:
  • 6mm: 6-7 ft-lbs
  • 8mm: 15-16 ft-lbs
  • 10mm: 31-32 ft-lbs
  • 12mm: 54-55 ft-lbs
  • 14mm: 87-88 ft-lbs

BEFORE INSTALLATION

• READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT.
• FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM.
• IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT WWW.TYGERAUTO.COM/CONTACT.

TORQUE VALUES

PARTS LIST

• x1  Driver/Left Tyger Rider
• x1  Passenger/Right Tyger Rider
• x1  Driver/Left Front Mounting Bracket
• x1  Passenger/Right Front Mounting Bracket
• x3 Driver/Left Center and Rear Mounting Brackets
• x3 Passenger/Right Center and Rear Mounting Brackets
• x16  8mm x 30mm Hex Bolts
• x16  8mm Lock Washers
• x16  8mm x 24mm OD x 2mm Flat Washers
• x16  8mm x 25mm Combo Bolts

Bottom View

Driver Left Side

PROCEDURE: REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. USE ILLUSTRATION TO IDENTIFY BRACKETS AND RUNNING BOARDS.

INSTALLATION STEPS

• STEP 1 Starting on the Driver/Left front of the vehicle, remove the plastic plugs or hex bolts covering the (2) threaded holes in the floor panel (Fig 1).
• STEP 2 Select (1) Driver/Left Front Mounting Bracket. Attach the Bracket to the mounting location with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers (Fig 2). IMPORTANT: DO NOT slide the Tyger Rider, (forward or backward or rotate), on the Brackets or damage to the finish on the Tyger Rider may result. DO NOT tighten the hardware.
• STEP 3 Select (1) Driver/Left Center and Rear Mounting Bracket. Repeat STEP 2 to attach the Bracket to the 2nd mounting location shown below (Fig 3-4).
• STEP 4 Continue to the 3rd and rear mounting locations (Fig 5 & 6). Repeat STEP 3 to attach (1) Driver/Left Center and Rear Mounting Bracket each to the 3rd and 4th/rear mounting locations (Fig 5 & 6).
• STEP 5 Select the Driver/Left Tyger Rider. Attach the Tyger Rider to the Mounting Brackets with (8) 8mm Combo Bolts (Fig 7). DO NOT tighten the hardware
• STEP 6 Level and adjust the Tyger Rider and tighten all hardware.
• STEP 7 Repeat STEPS 1-6 to attach the Passenger/Right Side Tyger Rider.
• STEP 8 Do periodic inspections of the installation to make sure that all hardware is secure and tight.

Customer Support:

• www.tygerauto.com/contact.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>