TYGER TG-LX3C82388 LanderX Running Board Installation Guide

June 1, 2024
TYGER

TYGER TG-LX3C82388 LanderX Running Board

TYGER-TG-LX3C82388-LanderX-Running-Board-Product

Product Information

Specifications:

  • Model: TG-LX3C82388
  • Driver/Left Side: TYGER LanderX
  • Passenger/Right Side: TYGER LanderX
  • Material: Steel
  • Finish: Black Powder Coat

Product Usage Instructions

Before Installation:
Read the instructions carefully before starting the installation. Remove contents from the box and verify all parts are present. Failure to identify damage before installation could lead to a rejection of any claim. If missing parts or any damage is found, please take a picture for the claim purpose.

Step 1: Passenger/Right Side Installation

  1. Start the installation under the passenger/right side of the vehicle. Locate the (4) factory running board mounting locations along the bottom and inner side of the body panel.
  2. The installation will use the 1st, 2nd, and 4th mounting locations. Brackets must be installed flat against inner sheet metal, remove sealant or undercoating as necessary.

Step 2:

  1. Remove rubber plugs from the front location.
  2. Select (2) 8mm Clip Nuts and slide each Clip Nut into the large hole and over the smaller hole next to it.
  3. Line up the threaded nut on the Clip Nut with the smaller hole in the body panel.

Step 3:
Select (1) Passenger/Right Mounting Bracket B and attach the bracket to the (2) Clip Nuts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers, and (2) 8mm Flat Washers. Do not fully tighten the hardware.

Step 6:
Locate the rear mounting location at the back of the cab. Repeat Steps 1-3 to install the (2) Clip Nuts and remaining Mounting Bracket B in the last mounting location.

Frequently Asked Questions (FAQ):

  • Q: What should I do if I find missing parts during installation?
    A: If missing parts are found, please take a picture for claim purposes and visit www.tygerauto.com/contact to file your claim.

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM THE BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT WWW.TYGERAUTO.COM/CONTACT.

TORQUE VALUES

Fastener Size Class 8.8 Torque (ft-lbs) Class 10.9 Torque (ft-lbs)
6mm 6-7 6-7
8mm 15-16 22-23
10mm 31-32 44-45
12mm 54-55 78-79
14mm 87-88 125-126

Parts List

  • x1 Driver/Left TYGER LanderX
  • x1 Passenger/Right TYGER LanderX
  • x3 Driver/Left Mounting Brackets
  • x3 Passenger/Right Mounting Brackets B.
  • x12 8-1.25mm Clip-On Nuts
  • x12 8-1.25mm x 25mm Combo Bolts
  • x12 8-1.25mm x 30mm Hex Bolts
  • x12 8mm x 24mm x 2mm Flat Washers
  • x12 8mm Lock Washers

Reference the letters printed on the brackets to determine mounting locations

TYGER-TG-LX3C82388-LanderX-Running-Board-Fig- \(1\)

Bottom View

ATTENTION:
Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.

TYGER-TG-LX3C82388-LanderX-Running-Board-Fig- \(2\)

PROCEDURE:
REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.

INSTALLATION

STEP 1
Start the installation under the passenger/right side of the vehicle. Locate the (4) factory running board mounting locations along the bottom and inner side of the body panel (Figs 1 & 2). NOTE: Installation will use the 1st, 2nd and 4th mounting locations.

NOTE: Brackets must be installed flat against inner sheet metal, remove sealant or undercoating as necessary.

Passenger/Right Side Installation PicturedTYGER-TG-LX3C82388-LanderX-
Running-Board-Fig- \(3\)

STEP 2
Remove rubber plugs from the front location (Fig 2). Select (2) 8mm Clip Nuts. Slide each Clip Nut into the large hole and over the smaller hole next to it. Line up the threaded nut on the Clip Nut with a smaller hole in the body panel (Fig 3).

Passenger/Right Side Installation Pictured

STEP 3
Select (1) Passenger/Right Mounting Bracket B (Fig 4). Attach the Bracket to the (2) Clip Nuts with (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers (Fig 5). DO NOT fully tighten the hardware.

Passenger/Right Side Installation Pictured

TYGER-TG-LX3C82388-LanderX-Running-Board-Fig- \(5\)

STEP 4
Move to the next mounting location along the body. Repeat STEPS 1 & 2 to install the Clip Nuts in the 2nd mounting location (Fig 2).

STEP 5
Select (1) Passenger/Right Mounting Bracket (FB in 4). Repeat STEP 3 to attach the Bracket to the 2nd (centre) mounting location (Fig 6).

Passenger/Right Side Installation Pictured

STEP 6
Next, locate the rear mounting location at the back of the cab. Repeat STEPS 1-3 to install the (2) Clip Nuts and remaining Mounting Bracket B in the last mounting location (Fig 7).

Passenger/Right Side Installation Pictured

STEP 7
Carefully unwrap the TYGER LanderX. Select the Passenger/Right TYGER LanderX. Note “P” on the back of the tube. Carefully position the Side Step up to the (3) Brackets. IMPORTANT: DO NOT slide, (front to back or rotate), the TYGER LanderX against the Brackets or damage to the finish may result. Attach the TYGER LanderX to the Brackets with (6) 8mm x 25mm Combo Hex Bolt assemblies (Figs 8-12). DO NOT fully tighten the hardware.

Passenger/Right Side Installation Pictured

TYGER-TG-LX3C82388-LanderX-Running-Board-Fig- \(8\)

STEP 8
Level and adjust the TYGER LanderX and tighten all hardware.

STEP 9
Repeat STEPS 1-8 for driver/left TYGER LanderX installation.

STEP 10
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals