TYGER TG-RS6C60248 6 Riser Running Boards Instruction Manual
- May 15, 2024
- TYGER
Table of Contents
RISER®
TG-RS6C60248
Parts List
x1 | Driver/Left 6inch Tyger Sidebar |
---|---|
x1 | Passenger/Right 6inch Tyger Sidebar |
x8 | Mounting Brackets |
x16 | 8mm x 30mm Hex Bolts |
x16 | 8mm x 25mm Combo Boltss |
x16 | 8mm Lock Washers |
x16 | 8mm x 24mm OD x 2mm Flat Washers |
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft-
lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
ASSISTANCE IS RECOMMENDED.
STEP 1
Start the installation under the Passenger/Right side of the vehicle.
a. For “Early” 2019 models, locate the 6 plugs along the bottom edge of the
body. Mounting Brackets will bolt to the 1st, 3rd, 4th and 6th threaded
mounting holes (Fig 1).
b. For “Late” 2019 models, all 4 mounting locations will be used.
Passenger/Right Side Installation Pictured
(Fig 1) Passenger/Right “Early” rocker panel mounting locations (arrows) NOTE: Hold Bracket up to body panel to help determine the correct mounting locations.
STEP 2
Remove the plastic plugs from the Passenger/Right front mounting location.
Select (1) Mounting Bracket. Attach the Mounting Bracket to the factory
threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat
Washers (Figs 2 & 3). DO NOT tighten hardware.
STEP 3
Repeat STEPs 1 & 2 to attach (3) Mounting Brackets to the (3) remaining
locations along the rocker panel (Figs 4-7). DO NOT tighten hardware.
STEP 4
Select the Passenger/Right 6inch Tyger Sidebar. Attach the Sidebar to the rear
faces of the Mounting Brackets with (8) 8mm Combo Bolts (Fig 8). DO NOT
tighten hardware.
STEP 5
Level and adjust the Tyger Sidebar and fully tighten all hardware.
STEP 6
Repeat STEPs 1-5 to attach the Driver/Left 6inch Tyger Sidebar.
STEP 7
Do periodic inspections to the installation to make sure that all hardware is
secure and tight.
Customer Support:
www.TygerAuto.com/Contact
V210922
Documents / Resources
|
TYGER TG-RS6C60248 6 Riser Running
Boards
[pdf] Instruction Manual
TG-RS6C60248 6 Riser Running Boards, TG-RS6C60248, 6 Riser Running Boards,
Running Boards, Boards
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>