TYGER TG-NB7J22398 Trax Nerf Bars Installation Guide

June 1, 2024
TYGER

TYGER TG-NB7J22398 Trax Nerf Bars Installation Guide
TYGER TG-NB7J22398 Trax Nerf Bars

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT:WWW.TYGERAUTO.COM/CONTACT.

TORQUE VALUES

Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft- lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126

  • x1 Driver/Left TYGER TRAX
  • x1 Passenger/Right TYGER TRAX
  • x1 Driver/Left Front Mounting Bracket (A)
  • x1 Passenger/Right Front Mounting Bracket (D)
  • x1 Driver/Left Center Mounting Bracket (B)
  • x1 Passenger/Right Center Mounting Bracket (E)
  • x1 Driver/Left Rear Mounting Bracket (C)
  • x1 Passenger/Right Rear Mounting Bracket (F)
  • x3 Driver/Left Support Brackets (G)
  • x3 Passenger/Right Support Brackets (H)
  • x6 10mm x 35mm Hex Bolts
  • x6 10mm x 30mm Hex Bolts
  • x6 10mm x 34mm OD x 3mm Flat Washers
  • x12 10mm x 20mm OD x 2mm Flat Washers
  • x6 10mm Lock Washers
  • x6 10mm Nylon Lock Nuts
  • x6 10mm Nut Plates
  • x6 8mm x 35mm Hex Bolts
  • x12 8mm x 25mm Combo Bolts
  • x6 8mm Lock Washers
  • x6 8mm x 28mm OD x 3mm Flat Washers
  • x12 6mm x 25mm Hex Bolts
  • x24 6mm x 22mm OD x 2mm Flat Washers
  • x12 6mm Nylon Lock Nuts

Parts List

Reference the letters printed on the brackets to determine mounting locations

Passenger/Right TYGER TRAX
Parts List 

Bottom View

ATTENTION: Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.

Passenger Right Side
Passenger Right Side

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY. FACTORY INSTALLED OR AFTERMARKET PRODUCT **
MUST BE REMOVED.**

STEP 1

Start installation toward the front of the Passenger/Right side of the vehicle (Fig 1).

Passenger/Right Side Installation Pictured
Installation Pictured

STEP 2

Determine if vehicle is equipped with threaded mounting inserts

Vehicles without threaded inserts:

a. Insert (1) 10mm Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld (Figs 2A & 2B).

Passenger/Right Side Installation Pictured
Installation Pictured

b. Select the Passenger/Right Front Mounting Bracket (D).

c. Attach the Bracket to the Nut Plate with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm Flat x 34mm Washer (Fig 3). DO NOT tighten hardware.
Installation Pictured

Vehicles with factory threaded hole in floor panel:

a. Locate the front, center and rear mounting locations (Fig 1).

b. Select the Passenger/Right Front Mounting Bracket (D).

c. Attach the Bracket to the front mounting location with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Fig 4).
DO NOT tighten hardware.

Passenger/Right Side Installation Pictured

STEP 3

Select (1) Passenger/Right Support Bracket (H). Attach the Support Bracket (H) to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts (Fig 5). Attach the Support Bracket ( H ) to the Mounting Bracket (D) with (1) 10mm x 30mm Hex Bolt, (2) 10mm x 34mm Flat Washers and (1) 10mm Nylon Lock Nuts (Fig 6). DO NOT tighten hardware.

Passenger/Right Side Installation Pictured
Installation Pictured

STEP 4

Repeat STEPS 2 & 3 to attach the Passenger/Right Center and Rear Mounting Brackets (E and F) and Support Brackets (H) to the center and rear locations (Figs 7A, 7B & 8). DO NOT tighten hardware.

Passenger/Right Side Installation Pictured
Installation Pictured
Installation Pictured

STEP 5

Select the Passenger/Right Side Sidebar.Attach the Side Sidebar to the Mounting Brackets with (6) 8mm Combo Bolts (Fig 9).
IMPORTANT: DO NOT slide Side Armor on the Mounting Bracket cradles, or damage to the finish may result.

Passenger/Right Side Installation Pictured
Installation Pictured

STEP 6

Level and adjust the Side Sidebar and tighten all hardware.

STEP 7

Repeat STEPS 1-6 to attach the Driver/Left Side Sidebar.

STEP 8

Do periodic inspections to the installation to make sure that all hardware is secure and tight.

TYGER Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals