TYGER TG-LX3J82378 LanderX Running Board Installation Guide

May 15, 2024
TYGER

TYGER TG-LX3J82378 LanderX Running Board

TYGER TG-LX3J82378 LanderX Running Board

BEFORE INSTALLATION

READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT

TORQUE VALUES

Fastener Size| Class 8.8 Torque (ft-lbs)| Class 10.9 Torque (ft- lbs)
---|---|---
6mm| 6-7| 6-7
8mm| 15-16| 22-23
10mm| 31-32| 44-45
12mm| 54-55| 78-79
14mm| 87-88| 125-126

Parts List

  • x1 Driver/Left TYGER LanderX
  • x1 Passenger/Right TYGER LanderX
  • x1 Driver/Left Front Mounting Bracket A
  • x1 Driver/Left Center Mounting Bracket B
  • x1 Driver/Left Rear Mounting Bracket C
  • x1 Passenger/Right Front Mounting Bracket D
  • x1 Passenger/Right Center Mounting Bracket E
  • x1 Passenger/Right Rear Mounting Bracket F
  • x1 Driver/Left Front Support Bracket G
  • x1 Driver/Left Center Support Bracket H
  • x1 Driver/Left Rear Support Bracket I
  • x1 Passenger/Right Front Support Bracket J
  • x1 Passenger/Right Center Support Bracket K
  • x1 Passenger/Right Rear Support Bracket L
  • x6 10-1.5mm x 30mm Hex Bolts
  • x12 10mm x 24mm x 2.2mm Flat Washers
  • x6 10mm Nylon Lock Nuts
  • x12 8-1.25mm x 25mm Combo Hex Bolts
  • x6 8-1.25mm x 35mm Hex Bolts
  • x6 8mm x 28mm x 3mm Flat Washers
  • x6 8mm Lock Washers
  • x12 6-1.0mm x 25mm Hex Bolts
  • x24 6mm x 22mm x 2mm Flat Washers
  • x12 6mm Nylon Lock Nuts

Reference the letters printed on the brackets to determine mounting locations

TYGER TG-LX3J82378 LanderX Running Board 1

Bottom View
ATTENTION : Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.

TYGER TG-LX3J82378 LanderX Running Board 2

PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. SIDE STEPS OR RUNNING BOARDS MUST BE REMOVED BEFORE INSTALLATION.

TYGER TG-LX3J82378 LanderX Running Board 3

STEP 1
Start installation on the Passenger/Right front of the of the vehicle. Locate the (4) pairs of mounting holes along the pinch weld (Fig 1). NOTE: Installation will use the 1st, 2nd and 4th mounting locations. Move to the front mounting location close to the front wheel opening. Locate the threaded mounting hole in the floor directly behind the mounting holes in the pinch weld (Fig 2).

TYGER TG-LX3J82378 LanderX Running Board 4

STEP 2
Select the Passenger/Right Front Support Bracket (FJ ig 3). Attach the Support Bracket to the back of the pinch weld with the included (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts (Fig 4). NOTE: Insert bolts from the outside of the pinch weld and through the Support Bracket. DO NOT tighten hardware.

TYGER TG-LX3J82378 LanderX Running Board 5

TYGER TG-LX3J82378 LanderX Running Board 6

STEP 3 Next, select the Passenger/Right Front Mounting Bracket D (Fig 3). Attach the Mounting Bracket to the threaded hole in the floor with the included (1) 8mm x 35mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer (Figs 5 & 6). Attach the Mounting Bracket to the rear facing side of the tab on the Support Bracket with the incJ luded (1) 10mm x 30mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut. DO NOT tighten hardware.

TYGER TG-LX3J82378 LanderX Running Board 7

STEP 4
Move to the 2nd mounting location (Fig 7). Select the Passenger/Right Center Support Bracket (FK ig 8). Repeat STEP 2 to attach the Bracket to the back of the pinch weld (Fig 9). Select the Passenger/Right Center Mounting Bracket E (Fig 8). Repeat STEP 3 to attach the Mounting Bracket to the front facing side of the tab on the Support Bracket with the included (1) 10mm x 30mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut (Figs 10 & 11). DO NOT fully tighten hardware at this time.
TYGER TG-LX3J82378 LanderX Running Board 8

TYGER TG-LX3J82378 LanderX Running Board 9

STEP 5
Continue to the last mounting location close to the rear wheel opening (Fig 12). Select the Passenger/Right Rear Support Bracket L (Fig 13). Repeat STEP 2 to attach the Bracket to the back of the pinch weld (Fig 14). Select the Passenger/Right Rear Mounting Bracket (FF ig 13). Repeat STEP 3 to attach the Mounting Bracket to the front facing side of the tab on the Support Bracket with the included (1) 10mm x 30mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut (Fig 15). DO NOT fully tighten hardware at this time.

Passenger/Right side Installation Pictured

TYGER TG-LX3J82378 LanderX Running Board 10

TYGER TG-LX3J82378 LanderX Running Board 11

STEP 6
Carefully unwrap the TYGER LanderX. Select the Passenger/Right TYGER LanderX. Line up the TYGER LanderX with the (3) Mounting Brackets. Attach the Drop Step to the Brackets with the included (6) 8mm x 25mm Combo Hex Bolts (Figs 16-18).

TYGER TG-LX3J82378 LanderX Running Board 12

STEP 7 Level and adjust the TYGER LanderX and tighten all hardware.
STEP 8 Repeat STEPS 1-7 for driver/left side TYGER LanderX installation.
STEP 9 Do periodic inspections to the installation to make sure that all hardware is secure and tight.

TYGER TG-LX3J82378 LanderX Running Board 14

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals