AVARRO 0E-HDMIEXT4K Hdmi Extender Over Single Utp User Manual

AVARRO 0E-HDMIEXT4K Hdmi Extender Over Single Utp

Introduction

Overview

0E-HDMIEXT4K is a slim transmitter receiver pair which is designed to extend HDMI 1080P@60Hz signals up to 70 m and 4K@60Hz (4:2:0) signals up to 40m via a single Cat 6a/7 cable. The transmitter can supply the power for the receiver.

You can control the source from the display’s location or control the display from source’s location via IR pass-through function. The transmitter and receiver are easy to install. They are space saving and offer solutions for home, office, digital
entertainment centers, control centers, conference rooms, school, and corporate training environments.

Features

• Slim appearance and space saving
• Bi-directional PoE, only one power adapter is needed.
• Via Cat 6a/7 cables, 4Kx2K@60Hz (4:2:0) output up to 130 feet (40m), 1080P@60Hz up to 230feet (70m).
• Via Cat 5e/6 cable, 4Kx2K@60Hz (4:2:0) output up to 115 feet (35m), 1080P@60Hz up to 198feet (60m).
• HDMI 1.4 with 4K and HDCP 2.2 compliant.
• Transfers bi-directional infrared control signal together with the HDMI signal.
• Use the transmitter and receiver pair to extend HDMI signals without additional settings.
• All connectors in one side for easy cabling

Package Contents

Before you start the installation of the product, please check the package contents:

• 1 x 0E-HDMIEXT4K
• 1 x Power Adapter (DC 18V 1A)
• 2 x IR Emitter
• 2 x IR Receiver (30-50KHz)
• 4 x Mounting Brackets
• 1 x User Manual

Panel

**Transmitter

**

Front Panel

BLINKING/OFF: Connection exceptions exist between the transmitter and the receiver.

Rear Panel

Note: Only one power adapter is needed at transmitter or receiver side.

2| HDBT OUT| Connect to the HDBT IN port of the receiver.
3| IR IN| Connect to an IR receiver cable. Secure the IR receiver with adhesive.

Note: The IR receiver enabled angle and distance:

Enabled Angel| 0°| 30° (Horizontal)| 15° (Vertical)|
Distance| 8m(Max)| 4.5m(Max)| 3m(Max)|
4| IR OUT| Connect to an IR emitter cable. Secure the IR emitter on the IR receiving sensor of display device with adhesive.
5| HDMI IN| Connect to an HDMI source.

Receiver

Front Panel

LED

| STREADY RED: Receiver is powered on.
2| LINK LED| STREAD GREEN: Link to transmitter has been established.

BLINKING/OFF: Connection exceptions exist between the transmitter and the receiver.

Rear Panel

Note: Only one power adapter is needed at transmitter or receiver side.

2| HDBT IN| Connect to the HDBT OUT port of the transmitter.
3| IR IN| Connect to an IR receiver cable. Secure the IR receiver with adhesive.

Note: The IR receiver enabled angle and distance:

 | Enabled

Angel

| 0°| 30°

(Horizontal)

| 15°

(Vertical)

|
Distance| 8m(Max)| 4.5m(Max)| 3m(Max)|
4| IR OUT| Connect to an IR emitter cable. Secure the IR emitter on the IR receiving sensor of display device with adhesive.
5| HDMI OUT| Connect to an HDMI display.

Specification

Technical

Video Signal Type| HDMI 1.4 with HDCP 2.2
Audio Format| Stereo, PCM 2.1/5.1/7.1, DTS, Dolby, pass through
 | SMPTE:
 | 1280x720P1,2,3,4,5,6,7,8, 1920x1080I6,8,
 | 1920x1080P1,2,3,4,5,6,7,8, 3840×21602,3,5, 4096×21602,3,5
 | VESA:
Input/Output Resolution Support| 800×6008, 1024×7688, 1280×7688, 1280×8008, 1280×9608,

1280×10248, 1360×7688, 1366×7688, 1400×10508,

1440×9008, 1600×9008, 1600×12008, 1680×10508,

 | 1920×12008
 | 1 = at 23.98 Hz, 2 = at 24 Hz, 3 = at 25 Hz, 4 = at 29.97
 | Hz, 5 = at 30 Hz, 6 = at 50 Hz, 7 = at 59.94 Hz,
 | 8 = at 60 Hz
Maximum Data Rate| 10.2Gbps
Maximum Pixel Clock| 340MHz
General

Operating Temperature| 0°C to + 45°C (32 to + 113 °F)
Storage Temperature| -20 to +70°C (-4 to + 158 °F)
Humidity| 20% to 90%, non-condensing
ESD Protection| ±8kV (Air-gap discharge)/

±4kV (Contact discharge)

Surge Protection| Voltage: ±1 kV
Power Supply| DC 18V 1A
Power Consumption

(Maximum)

| 8.8W (Pair)
General

Device Dimensions (W x H x D)| Transmitter/Receiver:

11.5cm ×2.1cm × 6.45cm/4.53” × 0.83” × 2.54”

Product Weight| Transmitter/Receiver: 0.22kg/0.48lb

Transmission Distance

Note: We recommend the use of T568B straight-through category cables.

3840 x 2160@60Hz 4:2:0 8bit

Cat 6a/7

| 40m/131ft
70m/230ft| 1080P@60Hz 36bpp

Wiring

The product packaging includes two pairs of IR cables, please refer to the following two applied installations with different remote handsets.

Applied installation 1

Control the DVD at TV side by DVD remote:

1. Control the DVD at TV side by DVD remote:
2. Connect an HDMI source (such as a DVD) to the transmitter.
3. Connect transmitter and receiver with a Cat5e/6/6a/7 cable.
4. Note: make sure Cat X cable is less than 230ft for 1080p. 130ft for 4K resolution.
5. Connect an HDMI display (such as a TV) to the receiver.
6. Connect the IR receiver cable to IR IN port of the receiver.
7. Connect the IR emitter cable to the IR OUT port of the transmitter, the IR emitter head should be secured over the center of the DVD IR window.
8. Connect the power adapter to DC 18V port.
9. Power on all the devices. Now you can enjoy the audio and video experience.
   

Applied installation 2
Control the TV at DVD side by TV remote:

1. Connect an HDMI source (such as a DVD) to the transmitter.

2. Connect transmitter and receiver with a Cat5e/6/6a/7 cable.
   Note: make sure Cat X cable is less than 230ft for 1080p. 130ft for 4K resolution. As show number 2 in figure.

3. Connect an HDMI display (such as a TV) to the receiver.

4. Connect the IR receiver cable to IR IN port of the transmitter.

5. Connect the IR emitter cable to the IR OUT port of the receiver, the IR emitter head should be secured over the center of the TV IR window.

6. Connect the power adapter to DC 18V port.

7. Power on all the devices. Now you can enjoy the audio and video experience.
   

Troubleshooting

Most problems that occur are due to simple issues. If you have trouble, please check the list of simple fixes below.

Six Steps of Regular Troubleshooting Routine.

1. Power: Make sure all devices are powered on. (source, extender, display device)
2. Indicator: Make sure LED indicators of extender are normal according to user manual.
3. Devices: Please make sure picture can be shown normally when connecting source to display devices directly.
4. Cable: Plug in and out HDMI/Cat X cable or try another HDMI/Cat X cable.
   • Cat 5e/6/6a/7 cable is recommended, do not use Cat 5 cable.
   • Please make sure Cat X cable is less than 230ft for 1080p, 130ft for 4K resolution.
   • Please make sure the two connectors of one Cat X cable are same standard (EIA/TIA 568B).
5. Compatibility:
   • Please test the source and display devices to determine whether there is compatibility issues.
   • HDMI extender supports 3G speed (4K@60Hz 4:2:0 8bit) maximum, when both HDMI source and display devices support 6G speed (4K@60Hz 4:4:4 8bit), display device will not output signal. (Even though all the LEDs of extender are normal.) Please set HDMI source resolution to 4K@60Hz 4:2:0 8bit or ask help from Source Device Supplier.
   • For Vizio TV, when every device is well connected and all the LEDs are normal. but Vizio TV cannot display well, please ask help from Vizio TV and update the TV setting.

Typical questions

1. How to deal with video flash or cut off during the installation?
   • Power indicator should be solid on. If not, please check if the power adapter is well connected.
   • Link indicator should be solid on, if it is blinking or off, it is likely a problem with your Ethernet cable, please change to a qualified cable (Cat 5e/6/6a/7, EIA/TIA 568B) and make sure the cable length is within the maximum distance (230ft for 1080p, 130ft for 4K).
2. How to deal with a weak or not working IR signal?
   • Make sure the IR cables are correctly installed according to the diagram above.
   • Check if the IR emitter head is secured over the center of the device IR receiver window. The best position may vary depending on the device, please refer to the device user manual. If the signal is weak, please try adjusting the position.
   • Pay attention to the control angle and distance as below: The control signal will be better when your controller is pointed at the IR receiver head directly
     Enabled Angle| 0°| 30°(Horizontal)| 15°(Vertical)
     ---|---|---|---
     Distance| 8m(Max)| 4.5m(Max)| 3m(Max)
3. How can I make the IR work with third party control devices?
   Please make sure the third-party device follows our pin definition as below:
   

Limited Warranty

Limited Warranty

General

Subject to the terms and conditions of this Limited Warranty, from the date of sale through the period of time for product categories specified in Section 1(b), ADI warrants AVARRO branded products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted.
Except as required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party.

ADI shall have no obligation under this Limited Warranty or otherwise if:

1. The product is improperly installed, applied or maintained;
2. The product is installed outside of stated operating parameters, altered, or improperly services or repaired;
3. Damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like.
4. Defects resulting from unauthorized modification, misuse, vandalism, or other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder.

ADI only warrants those products branded AVARRO and sold by ADI. Any other products branded by third parties are warranted by the third-party manufacturer for a period as defined by the third-party manufacturer, and ADI assigns to Buyer those warranties and only those warranties extended by such third party manufacturers or vendors for non-ADI branded products. ADI does not itself warrant any non-ADI branded product and sells only on an as is basis in accordance with ADI’s terms and conditions of sale.

Specific Warranties for product categories are as follows:

EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY

THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL ADI BE LIABLE TO ANYONE FOR ANY (I) CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND.OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY ADI’S OWN NEGLIGENCE OR FAULT AND EVEN IF ADI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or made orally by ADI or ADI’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets, or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying ADI’s products and shall not be construed as an express warranty or condition. Any suggestions by ADI or ADI’s agents regarding use, applications or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by ADI. ADI does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands and will cause its customer to understand that a properly installed and maintained product is not insurance or guarantee that such will not cause or lead to personal injury or property loss. CONSEQUENTLY, ADI SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING. However, if ADI is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty and shall be the complete and exclusive remedy against ADI.

Limitation on Liability to Buyer’s Customers.

Buyer agrees to limit liability to its customers to the fullest extent permitted by law. Buyer acknowledges that ADI shall only be deemed to give consumers of its products such statutory warranties as may be required by law and at no time shall Buyer represent to its customers and/or users of ADI products that ADI provides any additional warranties. By accepting the products, to the fullest extent permitted by law, Buyer assumes all liability for, and agrees to indemnity and hold ADI harmless against and defend ADI from, any and all suits, claims, demands, causes of action and judgments relating to damages, whether for personal injury or to personal property, suffered by any person, firm, corporation or business association, including but not limited to, Buyer’s customers and/or users of the products because of any failure of the products to detect and/or warn of the danger for which the goods were designed or any other failure of the products whether or not such damages are caused or contributed to by the sold or joint concurring negligence or fault of ADI.

Returns

Subject to the terms and conditions listed below, during the applicable warranty period, ADI will replace Product or provide a credit at purchase at its sole option free of charge any defective products returned prepaid. Any obligations of ADI to replace Limited Lifetime warranty products pursuant to this warranty which result from defect are limited to the availability of replacement product. ADI reserves the right to replace any such products with the then currently available products, or provide a credit in its sole discretion. In the event Buyer has a problem with any ADI product, please call your local ADI branch for return instructions:

For US call 1-800-233-6261
For Canada call 877-234-7378
For Puerto Rico call 787-793-8830

Be sure to have the model number and the nature of the problem available. In the event of replacement, the return product will be credited to Buyer’s account and a new invoice issued for the replacement item. ADI reserves the right to issue a credit only in lieu of replacement.

If any AVARRO branded products are found to be in good working order or such product’s inability to function properly is a result of user damage or abuse, the product will be returned to Buyer in the same condition as received and Buyer shall be responsible for any return freight changes.

Governing Law

The laws of State of New York apply to this Limited Warranty.

Miscellaneous

Where any term of this Limited Warranty is prohibited by such laws, it shall be null and void, but the remainder of the Limited Warranty shall remain in full force an effect.

References

• AVARRO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>