Toberich LED Barn Light 2 Pack 150W 18000LM Dusk to Dawn Outdoor Lighting User Manual
- June 14, 2024
- Toberich
Table of Contents
Toberich LED Barn Light 2 Pack 150W 18000LM Dusk to Dawn Outdoor Lighting
Product Information
Specifications
- Glue plug : 4PCS
- Shim : 4PCS
- Screw: Hand screw, screw, Hexagonal small wrench (4PCS)
- Wiring cap : 3PCS
- Black cable : 1PCS
- Red fixture wire : 3PCS
- Blue fixture wire : 1PCS
- Fixture ground wire : 3PCS
- Neutral supply wire : Blue
- Line supply wire : Red
- LUX Range: 80-150 LUX
Product Usage Instructions
Installation
To install the LED wall-mounted luminaire, follow these steps
- Align the holes of the handle and the lamp body respectively.
- Tighten the screws using the hand screw or Hexagonal small wrench.
- Straighten the cable and adjust its length as needed.
For standard mounting, use the following steps
- Apply glue plugs to secure the luminaire.
- Insert shims as needed for stability.
- Connect the red fixture wire to the fixed red wire.
- Connect the blue fixture wire to the fixed blue wire.
- Connect the fixture ground wire to the ground.
Connecting Power Cord
Follow these steps to connect the power cord
- Connect the neutral supply wire (blue) to the corresponding neutral supply wire.
- Connect the line supply wire (red) to the corresponding line supply wire.
FAQ
- Q: How many glue plugs and shims are included?
- A: The product includes 4 glue plugs and 4 shims.
- Q: How many screws are included?
- A: The product includes 4 screws, a hand screw, and a Hexagonal small wrench.
- Q: How many wiring caps are included?
- A: The product includes 3 wiring caps.
- Q: What is the purpose of the black cable?
- A: The black cable should be threaded through the hole on the handle to be installed on the lamppost.
- Q: What are the colors of the fixture wires?
- A: The colors of the fixture wires are red and blue.
- Q: What are the specifications for LUX range?
- A: The LUX range is between 80 and 150 LUX.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| Light will not come on. |
- Light switch is turned off.
- Fuse is blown or circuit breakers turned off.
- Incorrect circuit wiring.
|
- Turn light switch on.
- Replace fuse or turn circuit breaker on.
- Verify that fixture is wired properly
Lights come on during the day.| A. Photocell covered.| A. Clean photocell with damp cloth
FCC WARNING
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTES: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CONGRATULATIONS ON YOUR PURCHASE OF THIS LED WALL-MOUNTED FIXTURE
This light includes an integrated photocell which activates the light during
low illumination (at dusk) and de-activates the light when illuminated (at
dawn).
SAFETY INFORMATION
WARNING: Read all safety precautions and installation instructions carefully before installing or servicing this fixture. Failure to comply with these instructions could result in a potentially fatal electric shock and/or property damage.
- To reduce the risk of electrical shock or other personal injury, ensure the power is turned OFF at the fuse or breaker box before making any electrical connections.
- For outdoor use only.
- Must be connected to 110-120 volt, 60 Hz power source.
- Fixture should be mounted to a grounded junction box marked for use in wet locations.
- Suitable for wall mount.
- NOT suitable for ground locations. Minimum of 4 feet or higher.
- Utility Light should be installed by a qualified electrician or person experienced with household wiring. The electrical system, and method of electrical connection of the fixture, must be in accordance with the National Electrical Code and local building codes.
SUITABLE FOR WET LOCATIONS
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH CIRCUIT CONDUCTOR.
MINIMUM 90°C SUPPLY CONDUCTORS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE
WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED
Installation kit
PLANNING INSTALLATION
Carefully remove the fixture from the carton and check that all parts are
included. Be careful not to misplace any of the screws or parts needed for
installing the fixture.
NOTE: Please thread the black cable through the hole on the handle to be installed on the lamppost
PRODUCT ASSEMBLY STEPS
- Align the holes of handle and lamp body respectively.
- Tighten the screws.
- Straighten the wire and adjust the length of the wire.
INSTALLATION
Standard mounting
- Stick the handle of the lamp on the wall and draw the position of the installation hole. Then make 3 holes in the wall, diameter 0.31″ hole depth 1.6″
- Install the mounting rubber plug in the hole;
- connect the lamp power line, wiring polarity diagram, After connecting the wire, plug the wire into the handle;
- Install the lamp on the wall with screws;
CAUTION: Turn OFF the circuit breaker and light switch before beginning installation.
Arm mounting
- Install fixed pipe;
- connect the lamp power line, wiring polarity diagram, After connecting the wire, plug the wire into the handle;
- the lamp into the extension tube, lock the screw;
INSTALLATION
ATTACH POWER SUPPLY WIRE
- Connect the fixture ground wire (GREEN) to the ground supply wire using a wire nut.
- Connect the BLACK fixture wire to the BLACK (Line) supply wire using the wire nuts .
- Connect the WHITE fixture wire to the WHITE (Neutral) supply wire using the wire nuts .
NOTE: For proper connection, place the wire nuts over the wires and twist clockwise until tight.
RECOMMENDED: Wrap each wire nut with electrical tape (not included).
Thank you for purchasing this product.
- E-mail : support@toberich.com.cn