AViANCE Lighting HD54561 12 Inch 1-Light Polished Brass ADA Wall Sconce Instruction Manual
- June 1, 2024
- AViANCE lighting
Table of Contents
AViANCE Lighting HD54561 12 Inch 1-Light Polished Brass ADA Wall Sconce
Product Information
Specifications
- Model: HD54561
- Manufacturer: AVIANCE
- Power Source: Electric
- Material: Not specified
- Color: Not specified
Product Usage Instructions
Assembling & Installation Instructions
- The drawing shown may not exactly match the product enclosed.
- However, the installation instructions do apply to this product.
Assembling the Fixture
- Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
- Carefully unpack your new fixture and lay out all the parts on a clear surface.
- WARNING: THIS LAMP CANNOT BE UPSIDE DOWN!
Connecting the Wires
- Connect the electrical wires as follows:
- Connect the Black wire from the fixture to the black house (hot) Wire.
- Connect the white wire from the fixture to the white (neutral) house wire.
- Make sure all wire nuts are secured. You may wrap the connections with electrical tape.
- If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
FAQ
Q: What should I do if my fixture is not working after installation?
A: If your fixture is not working after installation, first double-check all wire connections following the provided instructions. If everything is connected properly, ensure that power is reaching the fixture by testing with a voltage tester. If you are still experiencing issues, please contact customer service for further assistance.
Q: Can I install this fixture outdoors?
A: The user manual does not specify if this fixture is suitable for outdoor use. It is recommended to check with customer service or refer to the product specifications for information on outdoor installation suitability.
Thank you for purchasing an AVIANCE product.
Need assistance with parts or assembly? Please email customer service at: info@aviancelighting.net.
ASSEMBLING & INSTALLATION INSTRUCTIONS
- The drawing shown may not exactly match the product enclosed.
- However, the installation instructions do apply to this product.
HD54561
- WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
- ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE
- Shut off the power at the circuit breaker box. Remove old fixture and all hardware from Junction Box.
- Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to lose any small parts necessary for installation.
- Attach the mounting plate to the junction box using two junction box screws as shown. The side of the mounting plate marked “GND” must face out. The junction box is not included.
- Guide fixture wires through the hole in the centre of the mounting plate.
- Follow wiring instructions carefully (see fig.2).
- Attach the lamp body (B) onto the mounting plate, aligning the back plate holes with the screw hole of the mounting plate on the side, then lock it securely with the mounting screw(C). Put the candle sleeve(D) and insert the lamp holder.
- Install the light bulb(not included) under the fixture’s specifications. NOTE: DO NOT EXCEED THE MAXIMUN WATTAGE RATING!
- Put the glass(A) and insert the cover of the lamp holder.
- WARNING: THIS LAMP CANNOT BE UPSIDE DOWN!
CONNECTING THE WIRES
- Connect the electrical wires as follows. Connect the Black wire from the fixture to the black house (hot) Wire. Connect the white wire from the fixture to the white (neutral) house wire. Make sure all wire nuts are secured. You may wrap the connections with electrical tape. If your outlet box has ground wires (green or bare copper) connect the fixture’s ground wire to it. Otherwise, attach the bare copper fixture wire to the green ground screw on the mounting plate.
- Tuck the wire connections neatly into the wall junction box.
Your installation is now complete. Return power to the junction box and test the fixture.
Thank you for purchasing an AVIANCE product. Need assistance with parts or assembly? Please email customer service at: info@aviancelighting.net.
©COPYRIGHT ALL RIGHTS RESERVED. AVIANCE LIGHTING, INC. DOC202403HD54561
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>