iOttie VLXWCG212 Velox Mini Qi2 Magnetic Air Vent Car Mount User Guide
- June 1, 2024
- iOttie
Table of Contents
iOttie VLXWCG212 Velox Mini Qi2 Magnetic Air Vent Car Mount
Product Information
- Slide the prongs of the Velox onto your vehicle’s air vent blades.
- Connect the USB-C cable to your vehicle’s USB-C port or auxiliary power outlet via a 10W adapter (not included).
- Tap your phone against the mount face. Charging will begin automatically.
Q12-CERTIFIED & MAGSAFE COMPATIBLE
- Only compatible with Qi2-enabled devices and MagSafe series iPhones and cases.
Declaration of Conformity (FCC)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class
B digital device, under Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 15cm between the radiator & your body.
IC warning statements
Warning Statement
RSS-GEN ISSUE 5, 8.4 User manual notice This device contains licence-exempt
transmitters)/receivers) that comply with Innovation, Science, and Economic
Development Canada’s license-exempt RSS(s). Operation is subject to the
following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This equipment should be installed and operated with a minimum distance of 0cm between the radiator & your body.
Follow @iottie for the latest news and updates! Please visit our website for more information. www.iottie.com
Thank you for your purchase.
Take 15% Off
- Your next order at iottie.com with code: THANK YOU 15
- If you’re happy with your purchase, please leave us a review on Amazon!
- If you are unsatisfied for any reason, please reach out to our support team at cs@iottie.com
Rethinking Packaging
- 100% recyclable and plastic-free
- Reduced packaging size
- Printed with soy ink
Learn more at iottie.com/about-us/sustainability
- If using a phone case, ensure it is Qi2 or MagSafe compatible, or your phone will not properly attach or charge.
Scan QR code for full manual & Product Registration
Specifications
- FCC Part 15 compliant
- General RF exposure evaluation
- Complies with FCC radiation exposure limits
- Minimum distance requirement: 15cm between the radiator & body
- IC RSS-GEN ISSUE 5, 8.4 compliant
- Canadian CAN ICES-3 (B)/NMB-3(B) compliant
FAQ
Q: Can I modify the device without manufacturer approval?
A: No, any changes not approved by the manufacturer could void your
authority to operate the equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>