iOttie VLXWCG212 Velox Mini Qi2 Magnetic Wireless Air Vent and Flush Mount User Guide
- June 1, 2024
- iOttie
Table of Contents
iOttie VLXWCG212 Velox Mini Qi2 Magnetic Wireless Air Vent and Flush
Mount
Product Installation
Flush
- Ensure car temperature is above 65 °F before installing for best results.
- Choose a mounting location and wipe the surface clean.
- Connect the cradle to the flush mount and tighten the cradle knob.
- Peel off film and press evenly for 30 seconds.
- To change the viewing angle, loosen the cradle knob and adjust the mount to your desired position. Tighten to secure it in place.
- Wait more than 20 minutes before mounting your phone for a secure hold.
Scan QR code for full manual & product registration
http://www.iottie.com/qr-
code?sku=ITMNCG000
Air Vent
- Connect the cradle to the vent mount and tighten the cradle knob.
- Only compatible with Qi2-enabled devices and MagSafe series iPhones and cases.
- Rotate the dial counterclockwise to extend the hook. If installing on a vertical air vent, rotate the hook so it is facing sideways.
- Insert the hook onto the air vent and secure the mount in place by rotating the dial clockwise until the mount sits flush against the vent.
- To change the viewing angle, loosen the cradle knob and adjust the mount to your desired position. Tighten to secure it in place.
- Connect the USB-C cable to your vehicle’s USB-C port or auxiliary power outlet via a 10W adapter (not included).
- Tap your phone against the mount face. Charging will begin automatically.
Declaration of Conformity (FCC)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. You can refer to the following completed FCC warnings. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Note
This equipment has been tested and found to comply with the limits for a
Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used under the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirements. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 15cm between the radiator & your body.
Specifications
- Compliance: FCC Part 15, IC RSS-GEN ISSUE 5
- RF Exposure Requirement : General
- Radiation Exposure Limits : FCC Compliant
- Distance Requirement : Minimum 15cm from the body
- Canadian Standards : CAN ICES-3 (B)/NMB-3(B)
FAQ
Q: What should I do if I encounter interference while using the device?
A: If you experience interference, try adjusting the positioning of the
device or relocating it to minimize potential disturbances. Ensure no other
electronic devices are causing interference.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>