HYPERX 4402228 Duo Cast USB Microphone User Guide

HYPERX 4402228 Duo Cast USB Microphone

Overview

• A Tap-to-mute sensor
• B LED ring
• C Gain control knob
• D Multifunction button
• E Headphone output
• F USB-C port
• G USB-C to USB-A cable
• H Mount adapter*
• I Supports both 3/8” and 5/8” thread sizes
  Supports both 3/8” and 5/8” thread sizes

Using with PC, Mac, PS5, or PS4

Connecting Headphones

Connect headphones to the headphone jack on the microphone for microphone monitoring and playback audio.

Selecting a Microphone Polar Pattern

Push the multifunction button to switch between the microphone’s two polar patterns, indicated by the LED ring.

LED RING

|

POLAR PATTERN

|

SOUND DIRECTION

---|---|---

Full to front

|

Cardioid

|

Front to full

|

Omnidirectional

|

Adjusting Microphone Gain

Muting the Microphone

Tap the tap-to-mute sensor to mute/unmute the microphone.
The LED ring will toggle to indicate the change in mute status.

Turning Microphone Monitoring On/Off

To turn microphone monitoring on/o¦, press and hold the multifunction button and tap the tap-to-mute sensor

Installing the Mount Adapter

1. Remove both the thumb screw and nut from the microphone stand.
2. Remove the microphone stand from the microphone.
3. Align the mount adapter with the microphone mount holes and secure the adapter with the thumb screw and nut.

Maintenance

Cleaning the microphone

1. Unplug all cables from the microphone before cleaning.
2. Put a very small amount of mild all-purpose cleaner on a soft cloth.
3. Wipe down the external surface of the microphone. Avoid getting any moisture in the microphone holes.
4. Let the surface of the microphone dry completely before use.
   • Do not use harsh cleaners such as products containing bleach.
   • Do not use compressed air and spray into the microphone.

Product Specification

Microphone

Power consumption: 5V 220mA (white light)
Sample/bit rate: 96kHz/24bit
Element: Electret condenser microphone
Condenser type: Two 14mm condensers
Polar pat t erns: Cardioid, Omnidirectional
Frequency response: 20Hz—20kHz
Sensitivity: -11dBV (1V/Pa at 1kHz)
Cable length: 2000±50mm
Weight: 502.9±5%
Lighting: RGB (16,777,216 colors)
Light effects: 2 zone
Connection type: USB-C to USB-A

Headphone Output

Impedance: 32 Ω
Frequency response: 20Hz – 20kHz
Maximum power output: ≥7mW
THD: ≤0.05% (at 1kHz/0dBFS)
SNR: ≥100dB (at 1kHz/0dBFS, A-wt)

FCC Compliance and Advisory Statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o¦ and on, the useris encouraged to try correct the interference by one or more of the following measures:

1. Reorient the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Any special accessories needed for compliance must be specified in the instruction manual.

HyperX and the HyperX logo are registered trademarks or trademarks of HP Inc. in the U.S. and/or other countries. All registered trademarks and trademarks are property of their respective owners. HP Inc. 1501 Page Mill Road, Palo Alto, CA 94304, USA. HP, HQ-TRE, 71025 Boeblingen, Germany. HP Inc UK Ltd, Regulatory Enquiries, Earley West, 300 Thames Valley Park Drive, Reading, RG6 1PT.

Customer Support

HyperX NGENUITY Software

To customize lighting, download the HyperX NGENUITY software at : hyperxgaming.com/ngenuity

Questions or Setup Issues?

Contact the HyperX support team or see the user manual at hyperxgaming.com/support/microphones

References

• HyperX | High Quality Gaming Gear – HyperX US
• HyperX | High Quality Gaming Gear – HyperX US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>