PHILIPS CRD22 WiFi Module User Guide

: June 13, 2024
: Philips

Table of Contents

Contents
Installation
- Install CRD22 into display
Safety Instructions
Technical Specifications
DETACHABLE ANTENNA USAGE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PHILIPS CRD22 WiFi Module

PHILIPS CRD22 WiFi Module

Installation

Install CRD22 into display

Step 1: Remove the two screws from cover and keep them for Step 3.
Step 2: Install CRD22 Wi-Fi module. Please plug-in it to the slot slowly and carefully.
Step 3: Use the screws in Step 1 to Fix the Wi-Fi module.

Safety Instructions

Safety precautions and maintenance

WARNING: Use of controls, adjustments or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards and/or mechanical hazards.

Read and follow these instructions when connecting and using your CRD22 Wi- Fi module:

Operation

Keep the CRD22 Wi-Fi module out of direct sunlight and away from stoves or any other heat sources.
Keep the CRD22 Wi-Fi module away from oil, otherwise the plastic cover may be damaged.
Remove any object that could fall into ventilation holes or prevent proper cooling of the CRD22 Wi-Fi module’s electronics.
Do not block the ventilation holes on the cabinet.
Do not subject the CRD22 Wi-Fi module to severe vibration or high impact conditions during operation.
Do not knock or drop the CRD22 Wi-Fi module during operation or transportation.
For doors or covers intended to be removed by operator for installation of accessory devices. Instructions shall be provided for the correct removal and reinstallation of the door.

Maintenance

Unplug the CRD22 Wi-Fi module if you are not going to use it for an extensive period of time.
Unplug the CRD22 Wi-Fi module if you need to clean it with a slightly damp cloth. The screen may be wiped with a dry cloth when the power is off. However, never use organic solvent, such as, alcohol, or ammonia-based liquids to clean your CRD22 Wi-Fi module.
To avoid the risk of shock or permanent damage to the set, do not expose the CRD22 Wi-Fi module to dust, rain, water or an excessively moist environment.
If your CRD22 Wi-Fi module becomes wet, wipe it with dry cloth as soon as possible.
If a foreign substance or water gets in your CRD22 Wi-Fi module, turn the power off immediately and disconnect the power cord. Then remove the foreign substance or water, and send the unit to the maintenance center.
Do not store or use the CRD22 Wi-Fi module in locations exposed to heat, direct sunlight or extreme cold.
In order to maintain the best performance of your CRD22 Wi-Fi module and ensure a longer lifetime, we strongly recommend using the CRD22 Wi-Fi module in a location that falls within the following temperature and humidity ranges.

– Temperature: 0-40°C 32-104°F
– Humidity: 20-80% RH

Service

The casing cover should be opened only by qualified service personnel.
If there is any need for repair or integration, please contact your local service center.
Do not leave your CRD22 Wi-Fi module under direct sunlight.

If your CRD22 Wi-Fi module does not operate normally, having followed the instructions set out in this document, please contact a technician or your local service center.

Warning :
This equipment is compliant with Class A of EN55032/CISPR 32. In a residential environment this equipment may cause radio interference.

NOTE : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

EU Declaration of Conformity / UK Declaration of Conformity

This device complies with the essential requirements of the Radio Equipment Directive (2014/53/EU) or Radio Equipment Regulations 2017(for UK).
The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the Radio Equipment Directive

Radiation Exposure Statement :

This equipment complies with CE radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & body.
The frequency, mode and the maximum transmitted power are listed below:
– 2400-2483.5MHz: < 20 dBm (EIRP) ( for 2.4G product only)
– 5150-5250MHz: < 23 dBm (EIRP)
– 5250-5350MHz: < 23 dBm (EIRP)
– 5470-5725MHz: < 30 dBm (EIRP)
– 5725-5875MHz: < 13.98 dBm (EIRP)

The device is restricted to indoor use only when operating in the 5150 to 5350MHz frequency range. ( for 5G product only)

| AT| BE| BG| HR| CY| CZ| DK
---|---|---|---|---|---|---|---
EE| FI| FR| DE| EL| HU| IE
IT| LV| LT| LU| MT| NL| PL
PT| RO| SK| SI| ES| SE| UK(NI)
UK| | | | | |

This device complies with Part 15 of the FCC / ISED’s license-exempt RSSs Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC/ISED/CE-RED Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Operations in the 5GHz products are restricted to indoor usage only.

Radiation Exposure Statement :
This equipment complies with FCC/ISED/CE-RED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Waste Electrical and Electronic Equipment-WEEE

Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2012/19/EU governing used electrical and electronic appliances, this product may not be disposed of with normal household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.

FOR MOBILE DEVICE USAGE ( >20cm/low power)

Radiation Exposure Statement :
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module:

KDB 996369 D03 OEM Manual v01 rule sections :

List of applicable FCC rules
This module has been tested for compliance to FCC Part 15
Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any other usage conditions such as co-location with other transmitter(s) or being used in a portable condition will need a separate reassessment through a class II permissive change application or new certification.
Limited module procedures
Not applicable.
Trace antenna designs
Not applicable.
RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. If the module is installed in a portable host, a separate SAR evaluation is required to confirm compliance with relevant FCC portable RF exposure rules.
Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.
Label and compliance information
The Final end product must be labeled in a visible area with the following: “Contains FCC ID: ARS-CRD22”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any co-located or simultaneous transmission with other transmitter(s) or portable use will require a separate class II permissive change re-evaluation or new certification.
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable to the Final host. The Final host will still need to be reassessed for compliance to this portion of rule requirements if applicable.

As long as all conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
IMPORTANT NOTE : In the event that these conditions can not be met (for example certain laptop configurations or co location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID/IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC/ Canada authorization.

Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.

OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the Host and Module. The Final product must be reassessed against all the essential requirements of the FCC rule such as FCC Part 15 Subpart B before it can be placed on the US market. This includes reassessing the transmitter module for compliance with the Radio and EMF essential requirements of the FCC rules. This module must not be incorporated into any other device or system without retesting for compliance as multi-radio and combined equipment.

Professional installation instruction

Installation personal
This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.
Installation location
The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby person in normal operation condition to meet regulatory RF exposure requirement.
External antenna
Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/ISED limit and is prohibited.
Installation procedure
Please refer to user’s manual for the detail.
Warning
Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules.
The violation of the rule could lead to serious federal penalty.

Technical Specifications

Item	Specification
Main Chip	MT7921AU
Front end I/O	Input Signal
Output Signal	USB 3.0
Power supply	Type
Input voltage	5V
Rating	5V 0.9A
Power consumption	4.5W
Input connector	USB 3.0
Operational Environment	Temperature
Humidity	20 – 80% (without condensation)
Storage Environment	Temperature
Humidity	10 – 90% (without condensation)

Note :

The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 1201Mbps.
It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE802.11n.
The Bluetooth part supports latest Bluetooth 5.2.

Gain(dBi)	Antenna Type	Connector Type
Frequency(GHz)	H- PLANIV- PLANE
2.4	1.53	2.54
2.45	2.08	2.78
2.5	2.55	2.53
5.15	1.68	2.57
5.35	2.69	2.·69
5.85	2.51	2.55

BT
Frequency (MHz)| Gain(dEi)| Antenna Type| Connector Type
2400| 2.88| PIFA| IPEX
2410| 2J 5
2430| 2.6
2440| 2.9
2450| 2.61
2460| 2.73
2470| 2.63
2480| 3
2490| 2.62
2500| 3.39

This device is intended only for OEM integrators under the following conditions: (For module device use)

The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

End Product Labeling FOR MOBILE DEVICE USAGE ( >20cm/low power)
This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 9190A-CRD22”.

Caution :

the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the Manufacturer Model Antenna Type Max Gain (dBi) Impedance (Ω) [JEM] [1510-0226-0085] [Dipole] [2.78] [50] equipment still complies with the e.i.r.p. limits as appropriate;
Where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

DETACHABLE ANTENNA USAGE

This radio transmitter [IC: 9190A-CRD22] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Manufacturer
[JEM]
Model
[1510-0226-0085]
Antenna Type
[Dipole]
Max Gain (dBi)
[2.78]
Impedance (Ω)
[50]

Version: V1.01 2022-12-23
TPV USA Corp
6525 Carnegie Blvd #200
Charlotte, NC 28211
USA

This product has been manufactured by and is sold under the responsibility of Top Victory Investments Ltd., and Top Victory Investments Ltd. is the warrantor in relation to this product. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.

Specifications are subject to change without notice