BEGA 12136PK27 Ceiling and Wall Luminaire Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 12136PK27 Ceiling and Wall Luminaire
Instructions for use
Product description
Safety
Overvoltage protection
Installation
Daylight threshold
Replacement of the LED unit
Accessory · Trim rings
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 12136PK27 Ceiling and Wall Luminaire

Specifications

Lamp Module connected wattage: 8.2 W
Luminaire connected wattage: 10.5 W
Rated temperature: 25°C to 40°C
Ambient temperature: max. 25°C to 40°C
Colour temperature options: 2700 K, 3000 K, 4000 K
Colour rendering index (CRI): > 90
Module luminous flux: Varies with colour temperature
Luminaire luminous flux: Varies with colour temperature
Luminaire luminous efficiency: Varies with colour
temperature

Safety Precautions

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning. The manufacturer does not accept liability for damage resulting from improper use or installation. Any modifications made to the] luminaire should be performed by authorized personnel.

Overvoltage Protection
The luminaire’s electronic components are safeguarded against overvoltage as per DIN EN 61547. For additional protection against transients, it is recommended to use separate overvoltage protection components available on the manufacturer’s website.

Luminaire Setup
Before mounting the luminaire onto a surface, ensure that the luminaire housing is inserted into the trim ring provided as an accessory.

Synthetic Diffuser Removal:
To detach the synthetic diffuser from the luminaire housing, turn it counterclockwise.

FAQ
Q: Can I install the luminaire myself?
A: No, installation and commissioning should only be carried out by a qualified electrician to ensure safety and proper functioning.

Ceiling and wall luminaire for indoor use

$BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $2$$

Instructions for use

Application
Ceiling and wall luminaire · indoor luminaire made of impact resistant synthetic diffuser and metal housing, for all lighting tasks.
They are ideal for places where a soft and uniform lighting distribution is required. Luminaire with motion sensor.

Product description

Metal housing, finish colour white
Impact resistant synthetic diffuser, white,
with bayonet closure
Integrated HF-motion sensor,
maximum range 10 m
2 mounting holes ø 5.5 mm
Distance apart 180 mm
2 cable entries for through-wiring for mains cable up to ø 10.5 mm max. 3 × 1.5@ Connection terminal 2.5@
Earth conductor connection
Complies with flicker requirements in accordance with IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit
220-240 V y 50/60 Hz
BEGA Thermal Switch®
Temporary thermal shutdown to protect temperature-sensitive components
Safety class I
Impact strength IK08
Protection against mechanical
impacts < 5 joule
– Conformity mark
Weight: 1.0 kg
This product contains light sources of energy efficiency class(es) D, E

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage in accordance with DIN EN 61547.
To achieve an additional protection against e. g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com

Lamp

Module connected wattage 8.2 W
Luminaire connected wattage 10.5 W
Rated temperature ta = 25 °C
Ambient temperature ta max = 40 °C

12 136 P K27

Colour temperature 2700 K
Colour rendering index CRI > 90
Module luminous flux 1165 lm
Luminaire luminous flux 851 lm
Luminaire luminous efficiency 81 lm / W

12 136 P K3

Colour temperature 3000 K
Colour rendering index CRI > 90
Module luminous flux 1205 lm
Luminaire luminous flux 880 lm
Luminaire luminous efficiency 83,8 lm / W

12 136 P K4

Colour temperature 4000 K
Colour rendering index CRI > 90
Module luminous flux 1255 lm
Luminaire luminous flux 917 lm
Luminaire luminous efficiency 87,3 lm /

Luminaire with trim ring:

Before installing onto the mounting surface the luminaire housing must be inserted into the trim ring (accessory).

Installation

LED are high-quality electronic components!Please avoid touching the light output opening of the LED directly during installation or relamping.
Pass the mains supply cable through the grommet into luminaire housing.
Fix luminaire housing with enclosed or any other suitable fixing material on to the mounting surface.
It is imperative to use the enclosed gaskets. Dismantle the mains supply cable approx. 60 mm.
Make earth and electrical connection to the terminals.
Place the synthetic diffuser to the luminaire housing and observe that the cam pins fit into the notches of the synthetic diffuser.
Screw in synthetic diffuser by turning it clockwise.
Thus, you reach a safe and vibration-resistant holding of the synthetic diffuser.
To release the synthetic diffuser from the luminaire housing, turn it counterclockwise.

$BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $4$$ The built-in motion sensor operates at a frequency of 5.8 GHz.
Detection range: 30° to 150°.
Operating temperature: -35° C to +70° C. With a wall mounting height of 1.8 m or ceiling mounting height of 2.6 m, the maximum range is 9 / 10 meters (see sketch).

$BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $5$$

The max. wall mounting height is 4.0 m and the max. ceiling mounting height is 6.0 m, in which the range reduces significantly.
Note: The installation distance between 2 luminaires with HF motion sensors should be more than 2 metres to prevent the sensors from being triggered incorrectly.
Local conditions can affect both the range and the detection area.

$BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $6$$

Detection Range
The sensor sensitivity (10% to 100%) can be precisely set for each specific application by selecting the combination on DIP switches 1-3.
Please note that a reduction in sensitivity also leads to a reduction in the range. $BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $7$$

Dwell time
By moving within the detection range the motion sensor switches on the LED module inside the luminaire with a defined dwell time. Select the DIP switch position 1-4 for the light switch-on time (5 s to 30 min.) after presence detection.
This function is deactivated if natural daylight is sufficient (exception: the threshold is deactivated). $BEGA-12136PK27-Ceiling-and-Wall-Luminaire- $1$$

Daylight threshold

Use DIP switches 1-4 to set the sensor level according to the lighting and the surroundings. The light does not switch on if the ambient brightness exceeds the set daylight threshold. Please note that the ambient brightness refers to the internal light that reaches the sensor.
If you deactivate the daylight sensor, the sensor switches to “Presence detection only” mode.
To set the luminaire to switch on and off automatically when it is dark or light outside, follow these steps:

A. Quick switch on and off:
You can switch the luminaire on and off quickly by simply pressing the switch (light switch) twice. The green LED indicator on the HF sensor flashes slowly for 5 seconds and the luminaire flashes twice.
B. Measurement of daylight:
The sensor measures the brightness of the surroundings for 1 second and stores this information.
C. Confirmation:
The luminaire is then in operation and the green LED indicator lights up for 10 seconds to indicate that the setting was successful. Thanks to this function, the luminaire can work well even if the daylight outside varies greatly. It is important to note that the last measured ambient light value always replaces the previous value. In addition, both the setting on the switch and the measured brightness value can replace each other.
The last action that was carried out remains valid.

Note: You can display the DIP switch settings via smartphone or tablet by scanning the QR code on the housing of the HF sensor.

Replacement of the LED unit

The designation of the LED unit is noted on a label in the luminaire.
The light colour and light output of BEGA replacement units correspond to those of the LED units originally fitted. The LED unit can be replaced by qualified persons using standard tools.
Disconnect from main supply.
Unscrew synthetic diffuser from luminaire housing by turning it counter-clockwise. Disassemble LED unit.
Assemble LED replacement unit.
Note installation instructions of the LED unit. Screw in a synthetic diffuser by turning it clockwise.
A damaged synthetic diffuser must be replaced.