SAVi Controls 00110021 125VAC Outlet Plug User Guide

: June 12, 2024
: SAVi Controls

Table of Contents

Read User Manual Online (PDF format)
Download This Manual (PDF format)

**SAVi Controls 00110021 125VAC Outlet Plug User Guide

**

Model number: 00110021

Max rating:

Resistive/Incandescent/Halogen 1800W
Motor ¾ HP

Power requirement

125VAC / 60Hz

Key Features:

Remote On/Off control
Manual On/Off control via front panel button
1 RGB LED indicator
Voice Control – Supports Amazon Alexa and Google Assistant

LED indicator:

There is an RGB LED indicator to show the status.
When the power is first turned on, it will display red, green and blue in sequence.
In general, red LED indicates that the output is off and green LED indicates output is on.
When the network is not set up and the device is in provisioning mode, press button 1 time, LED
flashes alternately red-blue (off) or green-blue (on) for about 15 seconds.

Resetting device to factory default:

Press and hold button >5 seconds to reset device to factory defaults. The status RGB LED will turn off and on (Red -> Blue ->Green), then LED flashes alternately red-blue (off) or green-blue (on) to indicate the device is in provisioning mode.

Manual Control:

Click the button to toggle the switch.

Installation:

Shut off power to the circuit.
Remove the wall plate and the existing switch (if mounted).
Identify and label the wiring on the existing switch, LINE (Hot), NEUTRAL, LOAD, TRAVELER (only used in 3-way circuits), GROUND before disconnecting the switch.
Disconnect wires from the existing switch and attach the corresponding wires to 00110020 screw terminals.
Secure the device to the wall box, reattach the trim, and restore power to the circuit to test. Wiring details:

Use copper wire only. 14 AWG or larger rated at 80°C or higher. Tightening torque should be 12 lbf in (14kgf-cm). Strip insulation 5/8″ (16mm)

FCC:
Supplier’s Declaration of Conformity 47 CFR 2.1077 Compliance Information Model: 00110020

Responsible Party – US Contact Information 2520 Marsh Lane, Carrollton, TX 75006-2401 214-785-6510

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE: The Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

IC:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

FCC ID:2BAZT10021001
IC: 30526-10021001